Search
158 articles for “Co-deposition”
-
Investigating the Combined Effect of FDM 3D Printing Parameters on Tensile Behavior of ABS Plastic Using Taguchi Method.
Abstract: Fused Deposition Modelling (FDM) is a commonly utilized method in additive manufacturing. FDM is greatly affected by its printing parameters, which is why selecting the proper parameters is crucial for obtaining the desired properties of 3D printed parts. In this paper we have experimentally and statistically studied the influence of FDM 3D printing parameters (infill pattern, infill density and layer thickness) on tensile strength using Acrylonitrile Butadiene Styrene (ABS) filament. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 161–169 Read article
-
Choking & Corrosion in Biomass Fired Boilers
Abstract: Biomass or Agricultural Waste is being widely projected and Promoted as an alternate to Fossil Fuels. Not only the reserves of Fossil Fuels - Coal and Oil are getting depleted, they are responsible for adding to the menace of pollution. Hence Biomass aptly qualifies as a non-polluting and renewable source of energy. One of the direct and common use of Biomass Fuel is for producing heat by combustion in a …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 389–397 Read article
-
Design and Fabrication of a 3D-Printed Femur Model: Insights into Mechanical Properties and Implant Research
Abstract: This study is an attempt to analyse the 3D printing of the female femur model of the central India region and provides ample suggestions for bone implant research. This article discusses the design development and experimental validation of finite element analysis (FEA) results with the 3D-printed bone model. Using CT scan data, the FE analysis is executed on a real femur bone of a 25-year-old female of 52 kg weight …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 329–338 Read article
-
Development and Performance Evaluation of GO–ZnO/PU Hybrid Nanocomposite Coatings for Improved Optical Transmission, Cooling, and Self-Cleaning in PV Systems
Abstract: The performance of solar photovoltaic (PV) modules with time is affected by thermal heating, dust buildup, and exposure to ultraviolet (UV) light; as a result, the power loss increases rapidly during the use condition. In this study, a polyurethane (PU) nanocomposite, fabricated with graphene oxide and zinc oxide (GO–ZnO), is invented and examined. Improvements in heat management, light transmission, and dirt resistance are planned for PV glass surfaces. The nanocomposite …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 243–249 Read article
-
Debris Flow Kinetics in Planetary Environments: A Systems Perspective
Abstract: Debris flow kinetics in planetary environments represent a critical intersection of geomorphology, fluid mechanics, and planetary science. These gravity-driven flow mixtures of solids, liquids, and gases play a key role in shaping planetary surfaces and recording environmental histories. This study adopts a systems perspective to analyze debris flow behavior across different planetary contexts, emphasizing the interconnected roles of material properties, energy transformations, and environmental forcing. By integrating rheological models with …
Published in International Journal of Universe · Vol. 1, Issue 2, 2025 · pp. 08–17 Read article
-
Parametric Investigations of Melt Flow Index for Nylon6-Mica Composite Based Hybrid FDM Filament
Abstract: The development of new hybrid filaments with improved mechanical and thermal properties has been driven by the increasing need for high-performance materials in additive manufacturing. This study explores the parametric investigations of the Melt Flow Index (MFI) for Nylon6-Mica composite-based hybrid Fused Deposition Modeling (FDM) filament. The investigation uses the Taguchi technique to examine how different extrusion temperatures, loads and the percentage of Mica filler affect the MFI, a critical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 165–173 Read article
-
Iron Ore Beneficiation through Reverse Flotation: Advances in Nanobubble-Assisted Flotation Technology for Lean Grade Ore Upgradation and Silica Removal: A Review
Abstract: The global demand for high-grade iron ore concentrates continues to surge as readily available rich ores become depleted. Iron ore beneficiation through froth flotation has emerged as a critical technology for upgrading lean-grade iron ores (typically 25–35% Fe) to produce high-quality concentrates (64–70% Fe) suitable for direct reduction and blast furnace operations. This comprehensive review examines the fundamental principles of flotation in iron ore beneficiation, with particular emphasis on the …
Published in International Journal of Minerals · Vol. 3, Issue 1, 2026 · pp. 1–30 Read article
-
Enhancing Surface Roughness of Polylactic Acid (PLA) 3D-Printed Parts Using CO₂ Laser Scanning: An Experimental Study on Parameter Optimization
Abstract: Fused deposition modeling (FDM) of polylactic acid (PLA) often suffers from poor surface finish due to the inherent layer-by-layer deposition process, limiting its use in high-precision applications. This study investigates CO₂ laser scanning as an efficient post-processing technique to reduce the surface roughness (Ra) of PLA parts while maintaining structural integrity. Specimens (100 × 80 × 5 mm) were fabricated with varying infill densities (35%, 70%, and 100%) to assess …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 503–511 Read article
-
Comparative Analysis of 3D Printed Nylon and PETG Specimens for Mechanical Properties.
Abstract: Fused deposition modeling (FDM) is one of the most used additive manufacturing techniques for polymer components. The polymer materials generally used in FDM process are polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), polyethylene terephthalate glycol (PETG), Nylon, etc. The mechanical properties of parts fabricated by FDM depend on material and process parameters. Several researchers have tried to investigate the influence of process parameters on mechanical properties for some of the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 7–14 Read article
-
Experimental Investigation on Mechanical Characterization of Electrodeposited Shot Peened Copper Coated and Un-Coated Mild Steel
Abstract: The fatigue strength of fabricated copper coating on mild steel specimens under repeated loading and the overall number of cycles to failure has been investigated. The specimens of copper coating on mild steel substrate are fabricated by using an electro deposition shot peening method. The hardness behaviour of fabricated specimens studied and the experimental work has been carried out by using Vickers Micro Hardness under the load of 20N force. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 279–288 Read article
-
Dosing Control of Urea in Selective Catalytic Reduction (SCR) to enhance the reduction of Nitrogen oxides
Abstract: Selective Catalytic Reduction (SCR) is an effective aftertreatment technique designed to comply with rigorous emission criteria established by global regulatory authorities for the elimination of nitrogen oxides from exhaust streams. Since NOx and ammonia reagents are poisonous and an excess of either is therefore very undesired, it poses an intriguing control problem, particularly at high conversion. SCR systems must reduce NOx emissions as much as possible and reduce the possibility …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 110–120 Read article
-
Optimization of Direct Ink Writing Process Parameters for Liquid Silicone Rubber/TiO2 Composite Ink
Abstract: The purpose of this research is to develop and optimize the Liquid Silicone Rubber (LSR)/Titanium Dioxide (TiO₂) composite inks in Direct Ink Writing (DIW)-based 3D printing systems. The primary research objective was to use enhancement of mechanical, rheological, and dielectric characteristics of LSR using TiO₂ reinforcement but still retain extrusion stability and dimensional consistency. TiO₂ content (0, 5, 10, and 15 wt%) and catalyst and glycerol ratios were regulated and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 240–259 Read article
-
Comparative Analysis of Pond Ash as a Partial Replacement of Sand as Subbase Material for Concrete Paver Block Hardstand sustaining storage of Bulk Cargo
Abstract: This work presents an industrial waste-derived subbase material that can take the place of conventional granular material for subbase in hardstand foundation construction. This industrial waste hugely deposited in the ash lagoons namely Pond Ash (PA) which is globally generated at an amount of 780 Metric Tons from thermal power plants annually ,as foundation material for hardstand construction, will not only help the cause of residual waste disposal problems but …
Published in Journal of Geotechnical Engineering · Vol. 12, Issue 3, 2025 · pp. 32–45 Read article
-
Sustainable Manufacturing: The Role of Additive Technologies in Waste Reduction
Abstract: Additive manufacturing (AM) is transforming modern manufacturing by significantly reducing material waste while enabling highly efficient production processes. Unlike conventional subtractive manufacturing methods—such as cutting, drilling, and milling—which remove excess material and generate large volumes of scrap, AM constructs objects layer by layer, depositing material only where required. This precise material placement minimizes waste generation and supports resource-efficient production, making AM a critical technology for sustainable industrial development. Beyond waste …
Published in Journal of Materials & Metallurgical Engineering · Vol. 16, Issue 1, 2026 · pp. 62–70 Read article
-
Enhancing Mutual Fund Investment Decision-making Using Machine Learning: A Survey
Abstract: In India, a significant portion of individuals save a part of their income for a secure future. Government and various public sector financial companies also provide some saving schemes through banks, post offices, and Life Insurance Corporation (LICs) such as Recurring Deposit (RD), Public Provident Fund (PPF), Sukanya Samridhhi Account (SSA) fixed deposits, etc. Over the past decade, many individuals have shifted their saving schemes to vigorously searching for investment …
Published in International Journal of Algorithms Design and Analysis Review · Vol. 2, Issue 1, 2024 · pp. 43–51 Read article
-
Comparative Assessment of Polymers and Composites for Solar Panels: Fundamentals, Performance Metrics, Manufacturing, and Sustainability
Abstract: This paper presents a comprehensive review of the main types of Photo Voltaic polymers and composites such as crystalline silicon (both mono- and poly-Si), thin-film tech (CdTe, CIGS, a-Si), perovskites, and organic/dye-sensitized cells and analyses the parameters such as efficiency, fill factor, open-circuit voltage, temperature response, and degradation. The analysis focusses on polymers and composites and manufacturing techniques like vapor deposition, roll-to-roll printing, and both solution and vapor techniques for …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 120–130 Read article
-
Atmospheric Determinants of Feed, Fodder, and Forage Contamination in a Changing Climate: Emerging Challenges for Sustainable Livestock Production
Abstract: Feed, fodder, and forage contamination represents a growing constraint to sustainable livestock production under a changing climate. Atmospheric determinants such as rising temperature, altered precipitation patterns, increased humidity, elevated carbon dioxide concentration, and enhanced aerosol and pollutant loads are increasingly recognized as critical drivers of contamination risks across feed supply chains. These atmospheric factors directly and indirectly influence crop growth, fungal proliferation, mycotoxin biosynthesis, microbial survival, and the deposition of …
Published in International Journal of Atmosphere · Vol. 3, Issue 1, 2026 · pp. 1–14 Read article
-
Design and Development of an Automated Robotic Algorithm for Blasting, Painting, and Barnacle Cleaning of Offshore Structures
Abstract: Marine surface maintenance tasks such as barnacle removal, abrasive blasting, and protective painting are traditionally carried out using manual methods that are labor-intensive, hazardous, and prone to variability in quality. These challenges are particularly significant for offshore structures, where harsh environmental conditions and restricted accessibility increase operational risks and maintenance costs. This paper presents the design and evaluation of an autonomous robotic system for automated surface preparation and coating of …
Published in Journal of Offshore Structure and Technology · Vol. 13, Issue 1, 2026 · pp. 1–12 Read article
-
Structure–Property Correlation of Infill Topology and Density on Tensile and Flexural Performance of FDM-Printed PLA and ABS
Abstract: Additive Manufacturing (AM), particularly Fused Deposition Modeling (FDM), has become a widely adopted manufacturing technology due to its design flexibility, low cost, and capability for rapid prototyping. However, the mechanical performance of FDM-printed components is strongly influenced by internal structural parameters such as infill pattern and infill density, in addition to the intrinsic material behaviour. This study investigates the structure–property relationship between infill topology, density, and mechanical performance of PLA …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 4, Issue 1, 2026 · pp. 26–37 Read article
-
Problems and Difficulties in the Additive Manufacturing of Composites with Carbon Fiber Reinforcement for Medical Application
Abstract: Amputation is more prevalent than one may think due to an accident, war, or disease. Prosthetics and associated orthotics have a combined global market value of $2.8 billion. Carbon fibre has found a market due to increased demand for foot prostheses. Fused deposition modeling (FDM) is a rapidly advancing three-dimensional (3D) printing technique. PEEK (polyether-ether-ketone) is a biocompatible, high-performance polymer that could potentially be utilised as an orthopedic surgery implant …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 1, Issue 1, 2023 · pp. 8–12 Read article