Search
116 articles for “carbides”
-
Investigation on Dry Sliding Wear Behaviour of AlSi7Mg0.3/B4C/ZrO2 Hybrid Composites using Taguchi Method
Abstract: Hybrid Aluminium/Boron carbide/Zirconium oxide (AlSi7Mg0.3/B4C/ZrO2) composites were fabricated utilizing stir casting technique by varying boron carbide content (4wt.%, 8wt.% and 12wt.%) and utilizing a fixed amount (4wt.%) of zirconium oxide particles. Optical microscopy revealed that B4C and ZrO2 particulates were dispersed uniformly in AlSi7Mg0.3 matrix. Dry sliding wear experiments were carried out utilizing the pin-on-disc tribometer with various levels of applied loads, sliding speeds and weight percentage of boron carbide …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 166–177 Read article
-
Dielectric Responses of Hybrid Polymer Matrix Composites at 2–3 GHz Microwave Frequencies
Abstract: AbstractMeasurement of dielectric properties of polymeric materials in the 2–3 GHz frequency region is very important for strategic applications such as communication electronics, rapid prototyping, and radiation assisted heating. As per international standards for industrial, scientific and medical applications (ISM) 0.9, 2.45 and 5.8 GHz microwaves can be used both for heating and communication purposes, of this 2.45 GHz is most widely used frequency, hence it is important to characterize …
Published in Journal of Polymer & Composites · Vol. 3, Issue 1, 2015 · pp. 1–11 Read article
-
Enhancements in Titanium Matrix Composites: A Multifaceted Exploration of Various Structural Ceramics Reinforcement
Abstract: This research study delves into the comprehensive exploration of Titanium Matrix Composites (TMCs) reinforced with Silicon Carbide (SiC), Alumina (Al2O3), and Boron Nitride (BN). The investigation is structured into three key phases, each addressing essential aspects of TMCs: Phase 1 involves materials and manufacturing, where TMC coupons were fabricated through the stir casting technique with varying compositions of aluminum and silicon carbide. Phase 2 focuses on characterization and defect detection, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 83–94 Read article
-
Fabrication and Experimental Investigation on Mechanical Properties of Quartz Particulate Reinforced Aluminium Composite
Abstract: Composites are processed by adding a reinforcement phase in a base metal. The base material is known as a matrix and the constituent that is added is called reinforcement. The matrix acts as a support while the reinforcements attach themselves in their respective positions which results in the synthesis of a material which has different mechanical and thermal properties compared to their raw materials. Since aluminium is used as a …
Published in Journal of Production Research & Management · Vol. 14, Issue 3, 2024 Read article
-
Fabrication and Mechanical Characterization of Hybrid Metal Matrix Composite Castings
Abstract: This work investigates and addresses the casting of a novel hybrid composite material with tungsten carbide and aluminum-silicate particles mixed at varying weight fraction rates. Production of hybrid composite has some advantages if it is processed by near net shape techniques. The simplest method for dealing with this hybrid composite is the turbulence produced by the vortex agitating technique. The vortex mixing method is used in this study to create …
Published in Journal of Experimental & Applied Mechanics · Vol. 15, Issue 3, 2024 · pp. 32–38 Read article
-
An Analysis of Machining Parameters for Metal Matrix Composite
Abstract: The electro-discharge machining analysis of hybrid Composite is presented in this work. Variables are chosen for the input process parameters. The material removal rate is acknowledged as an output parameter, together with the current, graphite and silicon carbide percentage and pulse on time. We used the Taguchi Method to conduct our experiments. To create the theoretical model and look into how process parameters affect the rate at which material is …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 76–85 Read article
-
E-glass Fiber Epoxy Composites: Role of Al2O3/SiC Fillers in Physical, Flammability and Mechanical Characteristics
Abstract: This study investigates the effects of varying weight percentages of Silicon Carbide and Alumina particles in epoxy-based composites, fabricated through compression molding, on their physical and mechanical properties. Comparing different studies on carbon fiber-reinforced polymer (CFRP) composites, as well as glass fiber-reinforced polymer (GFRP) composites, especially with the reinforcement of nanoparticles such as silicon carbide (SiC), alumina (Al2O3) and graphene. The investigations cover fabrication methods, like vacuum infusion and compression …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 238–250 Read article
-
A review on Methodology used for Dry Turning of AISI 52100 Steel
Abstract: Bearing steel like AISI 52100 is one of the most widely used high cutting steel in industry for manufacturing of bearing. A large amount of coolant is used for machining at high speed due to which increase there has been a significant increase in environmental hazards. So Green or Dry manufacturing with optimize cutting parameters and its effect on tool material & work piece quality need to be studied to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 467–475 Read article
-
Wear and Tribological Characteristics of Novel Metal Matrix Composites
Abstract: The development of advanced metal matrix composites (MMCs) with enhanced tribological performance has become increasingly important due to the premature failure of critical engineering components operating under severe wear conditions in automotive, aerospace, marine, defense, and power generation systems. Conventional composites such as Copper–Alumina and Aluminium–Silicon Carbide have demonstrated improved mechanical and wear characteristics; however, their widespread application is often limited by issues including particle agglomeration, non-uniform reinforcement distribution, porosity …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1326–1346 Read article
-
Mechanical Properties and Temperature distributionofHard Facingof SS-304 steelby using SAW
Abstract: Surface engineering is a multidiscipline activity aimed at tailoring the properties or surfaces of engineering materials to improve their function or service life. Mostly; as applied to metals, surface engineering includes processes; such as plating, diffusion treatment, physical and chemical vapor deposition, ion implantation, thermal spray coatings, selective hardening, hard facing, and a variety of less-used and proprietary processes. However; these processes will be described briefly and it will be …
Published in Journal of Automobile Engineering and Applications · Vol. 5, Issue 1, 2018 · pp. 18–29 Read article
-
Evaluation of Physico-mechanical Properties of Aluminium-based Matrix Reinforced with SiC and Porcelain for Automotive Components
Abstract: The present study examines an effort to synthesize the composition of the hybrid metal matrix, by using aluminium-based matrix reinforced with silicon carbide and ceramic porcelain material. Weight reduction and reliability of components are the main priorities when developing automotive parts, it is essential to select and use materials with a high strength to weight ratio. It was feasible to identify an appropriate material for automotive applications by using this …
Published in Journal of Automobile Engineering and Applications · Vol. 6, Issue 3, 2019 · pp. 37–43 Read article
-
Wear Analysis of Al-SiC Composite Valve Guide by Using ANSYS: A Review
Abstract: This application of using that can promise for the future growth. To finding a wear rate of the material and comparing to the cast iron basically using in continuous life. First of all aluminum silicon carbide using in aerospace engineering, Then some few year this composite material also can be used in automobile engineering. Aluminum silicon carbide mostly used there excellent properties like high wear resistance, low density, good strength …
Published in Journal of Automobile Engineering and Applications · Vol. 2, Issue 3, 2015 · pp. 23–29 Read article
-
Analysis of Surface Roughness and Material Removal Rate in Engine Valve Turning Operation of Material SUH3
Abstract: The purpose of this paper is to present an experimental work attempting to optimize the influencingprocess parameters involved in dry machining of the exhaust engine valve of material martensiticstainless steel grade SUH3. Looking at available literature it is observed that a lot of work can be donein the field dry machining related to surface integrity but no work can be reported on investigationimplementation of dry machining in engine valve manufacturing …
Published in Journal of Automobile Engineering and Applications · Vol. 8, Issue 1, 2021 · pp. 17–22 Read article
-
Metal Matrix Composites: Materials with the best property combination
Abstract: AbstractMetal matrix composites have been emerging out to be the most sought after materials in the field of Metallurgy and Materials Engineering. The basic driving force behind their wide applications is the fusion of ductile nature of metallic constituent and strong ceramic phases. This combination would always yield a structure with good toughness and longer service life. Aluminum-Silicon Carbide (SiC/Al) is a metal matrix composite that combine the properties of …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 3, 2018 · pp. 13–18 Read article
-
Effect of Fillers on Electrical Conductivity of Epoxy Composites
Abstract: AbstractThis paper reports, electrical conductivity studies carried out on RT cure epoxy resin (LY556+HY951) containing three different particulate fillers graphite (Gr) a soft material, silicon carbide (SiC) a hard material and a hybrid graphite and silicon carbide (Gr-SiC). The weight fractions of three different fillers were varied from 10% to 40 wt% in steps of 10%. Increased filler fraction increases the electrical conductivity of epoxy composites for all the three …
Published in Journal of Polymer & Composites · Vol. 6, Issue 3, 2018 · pp. 25–30 Read article
-
Functionally Graded Natural Fibre and SiC-reinforced Polymer Composite: Mechanical Properties
Abstract: Multifunctional materials, also called functionally graded materials (FGMs), are based on natural fibres or fillers and vary in composition and/or microstructure to control functional, structural, or thermal, properties. Functionally graded materials (FGMs) have been created for use in spacecraft, aircraft, and other engineering applications because they can withstand extremely high temperatures. Particle-reinforced FGMs, which make up the majority of FGMs, are made differently depending on their position. The mechanical and …
Published in Journal of Polymer & Composites · Vol. 11, Issue 4, 2023 · pp. 1–14 Read article
-
Minimum Energy Criteria for Machining to Determine Energy-Productivity Relationship
Abstract: In this research segment, cutting rates were changed while depth of cut and feed rate remained fixed. The results of cutting using a standard uncoated carbide insert were compared. Cutting speeds were maintained at a constant. After determining the optimal cutting condition for the equipment and material. To determine optimal tool life and cutting speed, turning operations were performed. In industrial cutting operations, flank wear reduces tool life. For single-point, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 4, 2023 · pp. 81–94 Read article
-
Exploration of Mechanical Characteristics and Microstructural Analysis of Copper Matrix Composites with Hybrid Reinforcements via Muffle Furnace Sintering
Abstract: Metal Matrix Composites (MMCs) have drawn a lot of interest in the area of innovative materials because of how widely they may be used. Due to their extraordinary qualities, such as high thermal conductivity, higher temperature endurance, improved corrosion resistance, and great weldability, copper matrix composites stand out among them. These qualities make them desirable and promising materials for uses including heat exchangers, automotive parts, and electrical components. In this …
Published in Journal of Polymer & Composites · Vol. 11, Issue 12, 2023 · pp. 119–126 Read article
-
Experimental Investigations on Aluminium Composites Materials Using Stir Casting Process
Abstract: In physical operations, accoutrements in motorcars and aeronautical machine factors, aluminium and its alloys are extensively used. In this study an effort is made to ameliorate the properties of aluminium essence matrix compound (A356) for manufacturing of machine rudiments taking High Tensile strength, Hardness, Wear resistance and low coefficient of friction, aluminium alloy (A356) reinforced with aluminium oxide, graphite and silicon carbide. In the current work, A356 as base metal …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 302–323 Read article
-
Utilizing Chemical Machining Methods in the Metalworking Sector
Abstract: Chemical machining is a kind of material removal technique used to produce desired shapes and dimensions by selectively or completely removing material through carefully regulated chemical attack using etchant solutions, which are solutions of acids or alkalis. One type of chemical machining is chemical milling, also known as contour machining, etching, or chemiluminescence. The aerospace industry uses chemical milling to remove thin layers of material from extruded parts for aircraft …
Published in International Journal of Manufacturing and Production Engineering · Vol. 2, Issue 1, 2024 · pp. 17–23 Read article