Search
372 articles for “Pulses”
-
Harmonic Analysis of 6-Pulse Diode Bridge Rectifier Circuits
Abstract: This paper analyzes the steady-state harmonic performance of the six-diode, 3-phase rectifier bridge circuits. A procedure for determining the frequency spectra of the different voltages and currents within the bridge circuit, resulting from a 60-Hz 3-phase supply, is presented. The effect of the smoothing shunt-capacitor is also demonstrated. Based on a Mathematica code, the paper presents the results of a comprehensive list of case studies. The procedure can handle unsymmetrical …
Published in Journal of Power Electronics and Power Systems · Vol. 10, Issue 2, 2020 · pp. 1–10 Read article
-
Steady State and Transient Analysis of 6-Pulse Rectifier Bridges Including Faulty Diodes
Abstract: This paper addresses the steady-state and transient responses of un-controlled faulty 6-pulse diode rectifier bridge circuits. The faulty bridges can include several simultaneous diode valves’ open- or short-circuits. An efficient representation of the diodes is adopted in order to describe their performance in both the forward and reverse directions. A set of simultaneous differential and algebraic equations simulating the faulty rectifier bridge is presented. Its numerical solution is obtained through …
Published in Journal of Power Electronics and Power Systems · Vol. 10, Issue 3, 2020 · pp. 19–31 Read article
-
Studies on Nanostructured Nickel Thin Film Coatings Deposited using Pulsed DC Magnetron Sputtering Process
Abstract: The purpose of this research work is to investigate the mechanical properties of nickel thin film. The nickel thin films were coated on glass substrate using pulse PDC power supply magnetron sputtering process in argon atmosphere. The effect of substrate temperature, effect of duty cycle and mechanical properties of nickel thinfilms has been presented in this paper. Coating deposited with substrate temperature at 250°C, had lower surface roughness (Ra<3 nm) …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 2, Issue 1, 2015 · pp. 8–14 Read article
-
Analysis of Six-Pulse Bridge Circuits Including Zener and Semiconductor Diodes – Part Two
Abstract: The present study offers a generic method for simulating and modelling six-pulse rectifier bridge circuits in the time domain. These circuits can include Zener and/or semi-conductor type diodes or even a mixture of them. The governing system of simultaneous algebraic and differential equations are listed and solved numerically using a computer code written in Mathematica. The flexibly written program can handle voltage sources of any time waveform, frequency or internal …
Published in Journal of VLSI Design Tools and Technology · Vol. 12, Issue 2, 2022 · pp. 13–21 Read article
-
Transients of Short-Circuits and Fault Clearance in 6-Pulse Diode Rectifiers
Abstract: The paper addresses the short-circuit transients in 6-pulse diode rectifier bridges. It includes also an investigation into the transients resulting from the subsequent fault clearance. Unit-step functions are efficiently used for representing the diode characteristics and emulating the fault switching actions. The short-circuit fault and its subsequent clearance are simulated by means of a time-dependent shunt resistance at the rectifier terminals. The governing set of simultaneous algebraic and differential equations …
Published in Trends in Electrical Engineering · Vol. 10, Issue 3, 2020 · pp. 6–14 Read article
-
Control Technique for Back-to-Back Converter Using Single Pulse Width Modulation
Abstract: This paper presents design and implementation of an analog controller for boost rectification and inversion required in the back-to-back converter used in doubly fed induction generator (DFIG) based wind energy conversion systems (WECSs). Detailed design of components of back-to-back converter is explained. The hardware module of this back-to-back converter is fabricated in the departmental laboratory. Testing is carried out on single phase as well as three phase rectifier section and …
Published in Journal of Instrumentation Technology & Innovations · Vol. 4, Issue 3, 2014 · pp. 1–13 Read article
-
Investigation of the Pulse Shape and Amplitude of 4He Gas Scintillations Produced by a 5.5 MeV Alpha Particle Source
Abstract: AbstractScintillation light is normally produced when ionizing particles such as alpha particles deposit their energy as they travel through a scintillating material, which can be solid, liquid or gaseous (e.g. 4He). In this project we compared scintillations produced in 4He gas by alpha particles (from the decay of 241Am) to those produced in plastic scintillator by cosmic-ray muons. The properties of photomultiplier and Si photomultipliers as sensors of scintillation light …
Published in Research & Reviews : Journal of Physics · Vol. 5, Issue 1, 2016 · pp. 18–29 Read article
-
A Review on Parametric Optimization of WEDM Technique for OHNS Steel
Abstract: In this study, the Wire Electrical Discharge Machining (WEDM) process for OHNS (Oil Hardened Non-Shrinking) steel, a high-performance material frequently used in the production of dies, punches, and precision tooling components, is optimized parametrically and validated experimentally. A continuously moving wire electrode and a sequence of electrical discharges are used in WEDM, a non-traditional machining method, to erode material and produce intricate and precise profiles, particularly in materials that are …
Published in Trends in Mechanical Engineering & Technology · Vol. 15, Issue 2, 2025 · pp. 29–35 Read article
-
Influence of EDM Process Parameters on MRR and TWR on Mild Steel and Cast Iron using Taguchi’s Method
Abstract: An alternative to conventional machining methods, Electrical Discharge Machining (EDM) uses electrical current for generating controlled sparks that erode surface of the material through thermal energy. Unlike traditional cutting processes, hard and electrically conductive materials with high precision can be machines very easily, which make it suitable for applications in tool and die manufacturing, aerospace, and automotive industries. Tool Wear Rate (TWR) and Material Removal Rate (MRR) for mild steel …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 614–627 Read article
-
Weldability of Aluminium Alloy Using Tungsten Inert Gas Welding Process for Mechanical Properties: A Review
Abstract: Metal components are joined using heat or pressure in TIG welding, sometimes referred toas Gas Tungsten Arc Welding. Pulsed current welding utilises inert gas for enclose the weld pools and electrodes. The intricate welding procedure known as TIG welding uses tungsten inert gas. It switches and forth between high and low level amps. Here, the weld quality and power output improve when the current is increased. Pulsed current TIG welding …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 1, 2023 · pp. 15–26 Read article
-
On The Energization and Steady-State Performance of 6-Pulse Diode Bridge Rectifiers Supplying Constant Voltage Loads
Abstract: The paper addresses the analysis of 3-phase 6-pule diode bridge rectifier circuits supplying a special load category representable by constant voltage sources. The applied Mathematica-based solution technique can handle symmetrical and unsymmetrical 3-phase voltages. The presented results include the phase currents on the AC side as well as the magnitude and wave shape of the output current on the DC side. Several case studies demonstrating the impact of the source’s …
Published in Trends in Electrical Engineering · Vol. 11, Issue 1, 2021 · pp. 14–23 Read article
-
Experimental Investigation of Weld Strength in Pulsed Current TIG Welding of AA 5052 Alloys – A Technical Review
Abstract: TIG welding, also known as Gas Tungsten Arc Welding, is a method in which metal parts are welded together using heat or pressure. Inert gas is used to cover the electrodes and weld pools. Superior alloys such as stainless steel, aluminium, and magnesium alloys must be used to make high-quality weld connections. In 1825, the aluminium metal was conceived and produced. This project is based on the 5052 aluminum alloy …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 1, 2022 · pp. 10–20 Read article
-
Solar Energy Materials Synthesis and Characterization
Abstract: The studies on the structural, microstructure and composition of the MoSe2 films are discussed in this research work. It deals with the optical properties of pulse plated films of MoSe2. Very little information has been given in the literature concerning the deposition current efficiency using pulse plating. In agreement with pulse plating theory, according to reference, the limiting overall plating rate of materials generally does not exceed the values for …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 6, Issue 3, 2019 · pp. 24–37 Read article
-
Firing a Laser into the Sky Diverts Lightning Offering Greater Protection to Installations
Abstract: Lightning bolts cause thousands of deaths every year worldwide. Since Benjamin Franklin’s invention of lightning rods made almost 300 years ago, the technology has not been changed even today. The same Franklin lightning rods are used on top of the buildings to steer lightning down to the ground so that they don’t pass through the buildings, and damage the structure or electrocute people. Researchers have recently developed a new type …
Published in International Journal of Photochemistry and Photochemical Research · Vol. 1, Issue 2, 2023 · pp. 46–56 Read article
-
Effect of Yogic Training on Selected Physiological and Psychological Variables of Sports persons.
Abstract: The primary objective of this research endeavor was to investigate the impact of Yogic training on specific physiological and psychological parameters among sportspersons. A sample comprising 50 sportspersons (25 male and 25 female), aged between 18 to 25 years, was randomly selected from Ahmedabad for the study. The intervention involved four weeks of Yogic training, during which data were collected at two time points: before the commencement of training (pre-test) …
Published in Research and Reviews : A Journal of Ayurvedic Science, Yoga and Naturopathy · Vol. 11, Issue 2, 2024 · pp. 35–39 Read article
-
Solar Sentry: Solar Power Module with Border Alert System for Fishing Vessel
Abstract: Fishermen are being caught and killed by the naval forces of the neighboring country, due to the lack of awareness about the ocean frontiers and advanced alert instruments in the boats. For this reason, maritime security has become a major concern of all coastal areas to protect the fishermen and provide assistance about sea frontiers via alerting, tracking, and monitoring of boat vessels. Thereby, a path-breaking technology of maritime border …
Published in International Journal of Robotics and Automation in Mechanics · Vol. 2, Issue 2, 2024 · pp. 1–6 Read article
-
An Investigation on Effect of Welding Current Mode on Weld Quality Characteristics of Microplasma Arc Welding of Inconel 625 Sheets
Abstract: Nickel alloys have gathered wide acceptance in the fabrication of components, which require high temperature resistance and corrosion resistance, such as metal bellows used in expansion joints in aircraft, aerospace and petroleum industry. In case of single-pass welding of thinner sections of this alloy, pulsed current microplasma arc welding was found beneficial due to its advantages over the conventional continuous current process. The paper focuses on studying the effect of …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 2, 2013 · pp. 8–13 Read article
-
Wireless and Wearable Real-time Health Monitoring Systems: A Review of Recent Developments
Abstract: This paper explores the interdependent relationship between mental and physical health, highlighting the impact of stress and anxiety on the body by introducing an innovative Real- Time Health Monitoring System. This system monitors both mental well-being and physical health using advanced physical health sensors and Facial Emotion Recognition (FER) technology. Leveraging high-precision sensors such as Temperature and pulse oximeters, it continuously monitors vital physiological parameters such as Body Temperature and …
Published in International Journal of Radio Frequency Innovations · Vol. 2, Issue 1, 2024 · pp. 1–7 Read article
-
Optimization of EDM Machining Characteristics of Reinforced Aluminium Metal Matrix Composites by Taguchi
Abstract: Aluminium alloys metal matrix composites (AMMC) play a vital role in various industries, such as aerospace and automobiles. This study investigates the machining characteristics of AL8079 - based composites reinforced with 15 wt. % TiB₂ and 5 wt. % MoS₂ using Electrical Discharge Machining (EDM). The machining process was optimized using the L9 orthogonal array (OA) Taguchi - based design of experiments, and input parameters were considered at three levels, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 939–951 Read article
-
Optimization of Machining Parameters of EN-27 Material Using Wire Electric Discharge Machining (WEDM)
Abstract: The optimization of Wire Electrical Discharge Machining (WEDM) parameters for EN-27 alloy steel, a high-strength material widely utilized in mechanical and structural applications, is the subject of this study's methodical analysis. Due to its hardness and poor machinability by conventional methods, WEDM is preferred for achieving precise dimensional accuracy and surface integrity. The primary objective of this work is to enhance machining performance by identifying optimal process parameters influencing Material …
Published in Journal of Production Research & Management · Vol. 16, Issue 1, 2026 · pp. 32–36 Read article