Search
272 articles for “Experimental measurements.”
-
Analysis of Surface Roughness and Material Removal Rate in Engine Valve Turning Operation of Material SUH3
Abstract: The purpose of this paper is to present an experimental work attempting to optimize the influencingprocess parameters involved in dry machining of the exhaust engine valve of material martensiticstainless steel grade SUH3. Looking at available literature it is observed that a lot of work can be donein the field dry machining related to surface integrity but no work can be reported on investigationimplementation of dry machining in engine valve manufacturing …
Published in Journal of Automobile Engineering and Applications · Vol. 8, Issue 1, 2021 · pp. 17–22 Read article
-
Triboelectric Charge Density Enhancement in Zinc Oxide Decorated Polymer Nanogenerators for Energy Harvesting Systems
Abstract: The growing need for wearable electronics, wireless sensor networks, and IoT devices has pushed research on triboelectric nanogenerator for long-term energy harvesting. However, traditional polymer-based TENGs' low triboelectric charge density restricts their energy conversion efficiency and practical performance. This research presents a zinc oxide (ZnO)-decorated polymer triboelectric nanogenerator designed to enhance surface charge density and improve electrical output. ZnO nanoparticles were synthesized using a hydrothermal method and uniformly deposited onto …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Enhancing The Mechanical Performance of Al6061/Graphite Composites Reinforced with Sic and Aluminium Oxide Processed by Stir Casting
Abstract: The study investigates the mechanical properties of aluminum alloy Al6061 reinforced with varying proportions of silicon carbide (SiC) (0 wt%, 4 wt%, 5 wt%, and 6 wt%) and aluminum oxide (Al₂O₃) (0 wt%, 4 wt%, 3 wt%, and 2 wt%), with a constant addition of 1 wt% graphite. The composites were fabricated using the stir casting process, an efficient and economical method for uniformly distributing ceramic reinforcements within the metal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 66–74 Read article
-
Investigation on the Variation of RMS Charge Radii of Potassium Isotopes Using SKHF Theory
Abstract: Information about the strong nuclear force and Electromagnetic force can be obtained from the nuclear charge radii measurements on a group of nuclei. Recent experimental findings of sudden enhancement of RMS charge radii of Potassium isotopes raised a question about the validity of shell theory of nucleus. This question has been addressed in this article by the inclusion of optimised tensor interaction term in the well tested Skyrme Hartree Fock …
Published in Journal of Nuclear Engineering & Technology · Vol. 12, Issue 3, 2022 · pp. 1–7 Read article
-
Exploring the Influence of Machining Parameters on Geometric Form and Orientation Controls (23 Design)
Abstract: This work explores the influence of machining parameters using on geometric form controls flatness and straightness as well as orientation control parallelism using an aluminum 6061 workpiece. Due to its good strength, machinability and cost- effectiveness, aluminum 6061 is widely used. In this experimental work, full factorial design is used and each factor has two levels. The response parameters chosen include flatness, straightness, and parallelism, which govern the form and …
Published in Journal of Experimental & Applied Mechanics · Vol. 16, Issue 1, 2025 · pp. 10–16 Read article
-
A Study to Evaluate the Effectiveness of a Structured Teaching Programme on Knowledge and Attitude Regarding Selected Comfort Measures Among Post-Caesarean Mothers
Abstract: Introduction: The study was conducted to assess the levels of knowledge and attitudes related to selected comfort measures among mothers who had undergone caesarean delivery, both before and after an intervention. It also aimed to identify any associations between these outcomes and certain demographic variables. Methods: A pre-experimental design using a single group with pretest and posttest measures was employed. The sample consisted of 100 post-caesarean mothers, chosen through a …
Published in International Journal of Midwifery Nursing And Practices · Vol. 4, Issue 1, 2026 · pp. 16–25 Read article
-
Enhancing Dimensional Accuracy of Affordable 3D-Printed Objects Via Solid Model Tuning For Industrial Manufacturing
Abstract: In the industrial applications of 3D printing (3DP) technologies, achieving precise dimensional accuracy and precision as well as improving surface quality are essential goals. With a focus on cost-effective engineering applications, this experimental research examines how solid model geometry tuning improves the internal and exterior dimensional accuracy of inexpensive 3DP technologies. Dimensional errors in the X, Y, and Z directions were meticulously measured on 3D parts made using Material Extrusion/Fused …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 201–210 Read article
-
An Overview of Examination of Some Basic Raw Materials for Adsorbent on Approach of Pollutant Mitigation and Treatment
Abstract: This research showcases the basic parameters that are required to produce bio-adsorbent suitable for adsorption process and their important role on treatment of contaminated water environment. The overview of the physicochemical parameters of the raw materials used for the production of the adsorbents, the particle size and the mix ratio were identified as a contributing factor to the rate of contaminants mitigation in the system. The effect of water pollution …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 01–16 Read article
-
Study on the Method of Prediction of Complete Inflation Time of Parachute
Abstract: In general, the parachute test is a long test period, expensive, and difficult to measure with accuracy, which makes it a very laborious and laborious task due to the strong nonlinearity of the fabric of the parachute. Therefore, attempts have been made to overcome this by using a parachute testbed or by simulation, but in our country, there is no numerical simulation of the parachute, and no research has been …
Published in Trends in Mechanical Engineering & Technology · Vol. 15, Issue 1, 2025 · pp. 25–31 Read article
-
Thermal Interaction Analysis Between Flexible Magnetic Abrasive Brush and Aluminium Alloy During Single-Pole MAF
Abstract: Magnetic Abrasive Finishing (MAF) is a precision surface‐finishing approach that employs magnetic abrasive particles (MAPs) within a managed magnetic field to eliminate micro-level material and enhance surface condition. In the finishing process, the friction created between the workpiece and the flexible magnetic abrasive brush (FMAB) leads to heat accumulation, which may badly affect the surface integrity. This study focuses on investigating the temperature distribution at the FMAB–workpiece interface to decrease …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1906–1918 Read article
-
Investigation of Miniature Venturi Flume
Abstract: A venturi flume is a device used to measure discharge in open channel. It consists of a convergent section followed by throat and a diverging section. The venturi flume normally occupies full width of channel on actual field. The present study proposes a new design of miniature venturi flume with reduction in width. The width reduction ratios of miniature flume to channel width (b/B) considered in the project are 0.33, …
Published in Journal of Water Resource Engineering and Management · Vol. 3, Issue 2, 2016 · pp. 26–31 Read article
-
Aluminum Oxide Nanofluids Thermal Conductivity Enhancement Analysis: A Review
Abstract: Aluminum oxide nanofluids are enhanced heat transfer fluids that utilize the thermal conductivity of aluminum oxide (Al2O3) nanoparticles suspended within a base fluid. As technology advances, more efficient high heat flux solutions are required to manage the higher concentration of power in smaller designs. In this review paper, data from multiple experiments pertaining to the thermal conductivity of Al2O3 nanofluids will be presented. Information is compiled from peer reviewed and …
Published in Journal of Thermal Engineering and Applications · Vol. 9, Issue 2, 2022 · pp. 48–58 Read article
-
An Experimental Study to Assess the Effectiveness of Valsalva Maneuver Prior to Intravenous Cannulation on Pain Perception among Patients Undergoing Venous Cannulation at HAHC Hospital in Delhi
Abstract: An experimental study was done to assess the effectiveness of valsalva maneuver prior to IV cannulation on pain perception among patients undergoing venous cannulation at HAHC hospital in Delhi. The objectives of the study were to assess the level of pain during IV cannulation among the experimental group, to assess the level of pain during IV cannulation among the control group, to compare the level of pain during IV cannulation …
Published in Research and Reviews : Journal of Surgery · Vol. 5, Issue 2, 2016 · pp. 1–6 Read article
-
Experimental Investigation of Influence of Key-shape Variation on Discharge Capacity of Piano Key Weir
Abstract: The piano key weir is a nonlinear free flow type weir with small foundation width. There are many geometrical parameters which influence the discharge capacity of the piano key weir. As in Labyrinth weir, the piano key weir is zigzagged in a plan to increase the crest length. Overhanging on both sides reduces the foundation width of such weir. To investigate the effects of key-shape variation of piano key weirs …
Published in Journal of Water Resource Engineering and Management · Vol. 3, Issue 3, 2016 · pp. 44–49 Read article
-
Axial Compression Behavior of Aluminum (Al), Glass/Epoxy (GFRP) and Hybrid Al-GFRP Crash-box: An Experimental and Digital Image Correlation Approach
Abstract: The study aims to understand the axial compression characteristics and fracture of cylindrical Aluminum (Al), Glass/epoxy (GFRP) composite and Hybrid Al-GFRP crash-boxes. The hollow Al tubes are fabricated by rolling and bonding a thin aluminum sheet followed by rivet joints. The GFRP samples are manufactured using the wet-hand layup technique followed by the vacuum bagging method. Hybrid samples are manufactured by covering GFRP tubes with aluminum sheets on the outer …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 304–313 Read article
-
Springback of High Strength Steel Sheet and Preventive Measures
Abstract: The purpose of this paper is to improve the accuracy output of cold stamping product by accommodating springback. This is an experimental study to improve the accuracy of springback analysis and die compensation process during CAE of part. The springback shape and the target part are used to optimize the die surfaces compensating springback. This paper describes the springback behavior of HSS steel based on phenomenon and preventive measures based …
Published in Trends in Mechanical Engineering & Technology · Vol. 11, Issue 3, 2021 · pp. 24–31 Read article
-
Engine Performance Analysis of Cottonseed Based Biodiesel Using Design Expert Statistical Based Tool
Abstract: Biodiesel is a biofuel acquired by substance forms from vegetable oils or creature fats and liquor that can be utilized in diesel engines alone or mixed with diesel oil. It is characterized as the mono-alkyl esters of unsaturated fats got from vegetable oils or creature fats. In basic words biodiesel is the item that gotten when vegetable oil or creature fat is artificially responded with a liquor to deliver unsaturated …
Published in International Journal of Industrial and Product Design Engineering · Vol. 1, Issue 1, 2023 · pp. 1–5 Read article
-
Effect of Cryogenic Treatment on Wear Characteristics of T42 High Speed Steel
Abstract: In this study cryogenic treatment is performed on AISI T42 HSS material and its wear characteristics are studied. Test of treated and untreated samples is taken on pin on disc wear testing machine at different loads and RPMs. The wear of the sample is measured. The wear resistance of the samples is also measured by weight loss method. The results are tabulated. An experimental effort to evaluate tool wear improvement …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 2, 2016 · pp. 70–79 Read article
-
Effect study of Cu2O in Perovskite (CH3NH3PbX3, X: I, Br, Cl) Solar Cell as Hole Transport Layer
Abstract: AbstractThe detailed modeling and mathematical simulation on perovskite solar cells have been performed with three various perovskite materials, such as “methyl ammonium lead trial halide (MAPbX3, MA= CH3NH3, X: I, Br, Cl)” with aid of solar cell capacitance simulator software (SCAPS) tools. The electrical possessions of MAPbX3 material performed as “active layer” and measured different parameters such as “open-circuit voltage (Voc), fill factor (FF), power conversion efficiency (PCE), and short-circuit …
Published in Journal of Microelectronics and Solid State Devices · Vol. 7, Issue 1, 2020 · pp. 5–10 Read article
-
Multipoint Deflection Analysis using Non-Contact Image-Based System
Abstract: Abstract: In this paper, the experimental study proposes a non‐contact image‐based system for multipoint deflection measurement through image processing based on a low‐cost consumer‐grade camera. Deflection monitoring is one alternative method that can become the indicators of bridge feasibility since this method is easy, effective, and can be used for multi-temporal application. The objective of this study is to determine the deflection of simply supported beam of span 1.2 m …
Published in Recent Trends in Sensor Research & Technology · Vol. 6, Issue 1, 2019 · pp. 13–17 Read article