Search
781 articles for “voltage (V)”
-
Implementation of Closed Loop Control of Flow in Air Blower System Using PLC and SCADA
Abstract: The intention of this paper is to design and implement the closed loop control of air flow rate in the air blower system. Desired value of flow rate is provide from the SCADA (Supervisory Control and Data Acquisition) and actual value of flow rate is measured through the flow sensor. Based on the difference between actual and desired value of flow rate, PLC (Programmable Logic Controller) increases or decreases the …
Published in Journal of Control & Instrumentation · Vol. 7, Issue 3, 2016 · pp. 39–43 Read article
-
Power Factor Improvement in BL-Pseudo Boost Converter-based BLDC Motor Drive
Abstract: Power factor correction (PFC) system increases the efficiency of power supply, delivering cost savings on electricity. Exchanging power supplies without PFC attract current short, high greatness beats. The beats can be smoothed out utilizing dynamic or inactive PFC procedures. This improves the power factor. A Bridgeless (BL) Pseudo boost converter is used for power factor correction in Brushless DC Motor (BLDC) drive. This converter working in spasmodic conduction mode (DCM) …
Published in Journal of Control & Instrumentation · Vol. 10, Issue 2, 2019 · pp. 40–49 Read article
-
Design and Implementation of SRF-PLL for Grid Synchronization
Abstract: The existing power system stands in a peculiar spot where a lot of innovative ideas keeps on forcing it to change itself to work more efficiently and consumer friendly. The micro-grid is one such area where the involvement of consumers in the power system is much more engaging than it was before. With the emergence of dependable and reliable renewable sources of energy such as solar and wind, the need …
Published in Journal of Control & Instrumentation · Vol. 10, Issue 2, 2019 · pp. 21–27 Read article
-
Continuous-Time Modelling of the Two-Input Fourth Order DC_DC Converter
Abstract: Two-input fourth-order integrated (TIFOI) converter is designed to process the power from two different sources Vg1 and Vg2. This converter facilitates regulation of dc-bus voltage and LVS current. In the power conversion process it performs bucking operation for first dc source Vg1, buck-boost operation for the second source Vg2. Power stage dynamics of the TIFOI converters is modeled using the state-space analysis. The system modelling plays an important role in …
Published in Journal of Control & Instrumentation · Vol. 12, Issue 3, 2021 · pp. 1–11 Read article
-
Operational Planning and Allocation of Distributed Generation in Distribution System: A Review
Abstract: Distributed generation refers to the generation of electricity from a variety of small, decentralized energy sources that are located close to the point of use, rather than relying solely on large, centralized power plants. These small-scale power sources can include renewable energy technologies like solar panels, wind turbines, and micro-hydro systems, as well as conventional fossil fuel generators or combined heat and power (CHP) systems. Distributed generation systems can be …
Published in Journal of Control & Instrumentation · Vol. 14, Issue 2, 2023 · pp. 24–29 Read article
-
Genetic Algorithm Application for Efficient Load Frequency Control
Abstract: Load frequency control (LFC) is known to be significant control strategy for operation in electric power grid that entails balancing the electrical power provided by power plants with the electrical power consumed by the load. The primary purpose of LFC is to ensure that the power system functions within a specific frequency range and that the power provided by power plants matches the power used by the load. Power system …
Published in Journal of Control & Instrumentation · Vol. 14, Issue 3, 2023 · pp. 1–14 Read article
-
Investigation of Physical Characteristics and Machining Parameters of Improved Al-SiC MMC Using Dry EDM Process for Aerospace Industries
Abstract: Aluminium-based composite is widely used in aerospace and automobile industries because it is lighter in weight; but the trouble is that it is easily worn-out and life of the components is decreased. To overcome these problems, aluminium silicon carbide composite material has been developed with good wear-resistance, hardness and lighter weight. Silicon carbide has good mechanical properties like wear resistance, hardness, toughness and high melting point. Silicon carbide weight fractions …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 1, 2018 · pp. 15–32 Read article
-
Optimization of Process Parameter in Electrical Discharge Machining
Abstract: This is the non-traditional machining process. The high surface finish of the material is required. More complex shape of material is required. Wire EDM is one of the nontraditional machining processes. Surface roughness and kerf width are of crucial in the field of machining processes. This paper uses the Grey relational theory and Taguchi optimization technique, in order to optimize the cutting parameters in Wire EDM for D3 steel material …
Published in Journal of Experimental & Applied Mechanics · Vol. 11, Issue 2, 2020 · pp. 4–10 Read article
-
Comparative Analysis of Perturb & Observe and Incremental & Conductance MPPT Algorithms
Abstract: AbstractMaximum power point tracking (MPPT) technique implemented on a Photo-Voltaic (PV) system is meant for increasing its efficiency. In literature may research work claims MPPT technique as one of the most efficient way in enhancing output power generated. The output electrical parameters (V-I curve) of PV (photovoltaic) system depends on the irradiance, temperature, configuration, environmental conditions and analogy of a PV system. MPPT regulates the system at the reference voltage …
Published in Journal of Electronic Design Technology · Vol. 9, Issue 2, 2018 · pp. 7–13 Read article
-
Optimization of a Digital Adder Design Using MOSFET and FinFET Technology
Abstract: AbstractIn this study, a very low power high speed Adder is presented by using short gate mode technique and voltage scaling system for FinFET. MOSFET and FinFET technique is used on 32 nm by adders which compare delay and average power. Parametric study of fins vs. power is also performed in the study. Synopsys HSPICE software is used for obtaining the simulation results. Simulation results show that low power is …
Published in Journal of Electronic Design Technology · Vol. 9, Issue 2, 2018 · pp. 30–33 Read article
-
A Review of Single-Phase Grid Connected Transformerless Solar PV Inverter Topology
Abstract: Abstract: Owing to low cost and system compactness, transformerless inverters became popular in single-phase grid connected photovoltaic (PV) systems. Improvement of conversion efficiency, reduction in distortion of the grid current and minimizing common mode leakage current are the major concerns in these inverters. The purpose of this paper is to review on various transformerless solar PV inverters. In this paper, the single-phase inverters are classified into two major categories: 1) …
Published in Journal of Electronic Design Technology · Vol. 10, Issue 1, 2019 · pp. 1–7 Read article
-
Design and Development of a Multifunction FPGA-based Data Acquisition System using Nonlinear Duty-cycle Modulation Technique
Abstract: AbstractA new generation of DAQ based on duty-cycle modulation technique is presented. It describes the design and prototyping of a FPGA-based data acquisition and signal generation board using the duty-cycle modulation technique and with computer-based software interface. The system is built around the DE0-Nano development board that embeds an Altera cyclone IV FPGA in which a NIOS II processor running at 100 MHz has been instantiated. The conversion technique from …
Published in Journal of Electronic Design Technology · Vol. 10, Issue 3, 2019 · pp. 8–26 Read article
-
Hybrid Solar PV–Wind Energy System: A Performance Study
Abstract: The solar PV and, wind energy hybrid technology is based on the concept of a modular, scalable, distributed renewable energy system designed and optimized for on and off grid installations. This kind of system is fully integrated hybrid system that combines wind energy units with PV technology in a compact footprint, creating the greatest energy generation density. The hybrid concept is unique and disruptive, seamlessly utilizing wind and solar energy …
Published in Journal of Electronic Design Technology · Vol. 8, Issue 1, 2017 · pp. 7–10 Read article
-
Maximum Power Point Tracking for Solar PV System
Abstract: There is an ever increasing demand for energy in today's world. The photovoltaic (PV) systems are the suitable options for satisfying an ever increasing need for energy and thus are being used widely around the globe. Some special methods are required for extracting the maximum available power out of PV systems because they are nonlinear in nature. The nonlinear characteristic of the IV curve of PV module has a unique …
Published in Journal of Electronic Design Technology · Vol. 7, Issue 1, 2016 · pp. 14–21 Read article
-
An Energy Stored Quasi Z-Source Cascaded Multilevel Inverter
Abstract: In the world today, there is a huge demand of power, although we have sufficient energy generation technique, renewable energy power generation plays a major role, like solar. This paper is about the control technique, which includes ES-QZSI combined with CMI and energy storage in order to get constant output power without fluctuation from the solar panel. Combines cascaded multilevel inverter and quasi Z-source inverter. Battery is used to balance …
Published in Journal of Electronic Design Technology · Vol. 7, Issue 2, 2016 · pp. 24–34 Read article
-
A DC-DC Boost Converter for Energy Harvesting
Abstract: Energy harvesting is an emerging technology used for wireless remote and local devices. For powering these devices such as wireless nodes battery is required which demands replacement after discharging. Energy harvesting technique helps in developing battery-free operation for these devices. To do so we need power management system which itself is power efficient. These power management systems may use many technologies but one of them is DC-DC boost converter using …
Published in Journal of Electronic Design Technology · Vol. 7, Issue 3, 2016 · pp. 7–12 Read article
-
Fuel Cell Power Conditioning for Low Power Applications
Abstract: Fuel Cells are the important building blocks of hydrogen-based applications. Proton Exchange Membrane Fuel Cell (PEMFCs) are useful for ambient temperature operating conditions. Fuel Cells cannot be interfaced to loads directly owing to many sources of power losses. Power Conditioning and Interface are equally important for driving loads using Fuel Cell generated power. Paper discusses the requirements of power conditioning, types of DC–DC converters, Experimental work performed on DC–DC converter …
Published in Journal of Electronic Design Technology · Vol. 7, Issue 3, 2016 · pp. 13–23 Read article
-
Solar Electric Powered Hybrid Vehicle
Abstract: The renewable energy is vital for today’s world as the nonrenewable sources that we are using are going to get exhausted in near future. The solar vehicle is a step in saving these nonrenewable sources of energy. The basic principle of Solar/Electric Powered Hybrid Vehicle (SEPHV) is to use energy that is stored in a battery during and after charging it from a solar panel. The charged batteries are used …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 3, 2015 · pp. 9–16 Read article
-
HVDC Low Loss Switching Boost Converter Using Auxilary Circuit
Abstract: AC supply is available in different frequencies so many problems occur in different etiquettes; like battery charging needs the nonstop DC supply. Because of switching losses(AC to DC converters) are befalls in the converters. A new soft switching boost converter with an auxiliary or secondary switch and resonant circuit is projected in this work. The resonant circuit is consisted of a resonant inductor Lr, two resonant capacitors Cr1 Cr2, two …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 3, 2015 · pp. 33–39 Read article
-
Analysis of LSDCCFF at 0.09 µm Technology
Abstract: The traditional low swing differential conditional capture flip-flop (LSDCCFF) for LC resonant clock distribution network has wide range of applications but has poor power consumption. These characteristics can be improved by using the modified LSDCCFF. This paper presents the design of modified LSDCCFF with less delay and low operating power. The implementation of the circuit is done using LSDCCFF. By using voltage scaling technique, the average power consumption can be …
Published in Journal of Electronic Design Technology · Vol. 5, Issue 2, 2014 · pp. 32–39 Read article