Search
942 articles for “Mechanical performance”
-
Performance Evaluation of Concrete with Binary and Ternary Blends of Fly Ash, Silica Fume, and Fiber Reinforcement
Abstract: This study evaluates the effect of ground granulated blast furnace slag (GGBS) as a partial replacement for cement on the mechanical properties of concrete, focusing on compressive and split tensile strength. Concrete mixes were prepared with GGBS replacement levels of 0%, 25%, and 50% and subjected to different curing methods, including water curing, steam curing, and conceal curing. These curing methods were selected to investigate their impact on hydration, strength …
Published in Journal of Construction Engineering, Technology & Management · Vol. 15, Issue 3, 2025 · pp. 40–45 Read article
-
Feedback Based Three Finger Robotic Gripper
Abstract: This research presents the development and validation of a novel three-finger robotic gripper system enhanced with force feedback capabilities. Leveraging Force-Sensing Resistor (FSR) sensors and servo actuators, the gripper is engineered to dynamically adjust its grasp based on real-time force feedback. Through a series of iterative design iterations and experimental validation, the gripper demonstrates robustness and adaptability in various gripping scenarios. The integration of force feedback allows the gripper to …
Published in Journal of Mechatronics and Automation · Vol. 11, Issue 1, 2024 · pp. 11–17 Read article
-
Design and Synthesis of Functionalized Copolymers for Enhanced Interfacial Compatibility in Polymer Matrix Composites
Abstract: Interfacial adhesion between the polymer matrix reinforcing phase affects significantly the mechanical and thermal behavior of polymer composites. The study reports on the design and synthesis of functionalized copolymers in the efforts to establish interfacial compatibility based on chemical design. The reinforcements were functionalized doping polar functional groups such as glycidyl methacrylate and maleic anhydride during free-radical copolymerization to form copolymerizing reactive sites that interacted with the reinforcement surfaces. Confirmation …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1404–1418 Read article
-
Mathematical Modeling and CFD Analysis for Protype Model Development of a Low-cost Hybrid Power Operated Mini Kitchen Chimney for Rural Households
Abstract: Home chimneys remove pollution by products of fossil fuels from the atmosphere. Today's environmental problems are worsening rapidly due to technology and population growth. Thus, researchers developed a hybrid micro kitchen chimney to help rural residents at a low cost. This small hybrid chimney simplifies rural cooking. A kitchen chimney is the best way to remove smoke, grease, stink, stains, oil droplets, and more from the kitchen. It helps ventilate …
Published in International Journal of Energy and Thermal Applications · Vol. 1, Issue 1, 2023 · pp. 14–28 Read article
-
Advancements in Windmill Technology: Comprehensive Research on Conventional and Piezoelectric Windmills
Abstract: This research delves into the structural components and mechanisms of conventional wind turbines, emphasizing blade material considerations for optimal performance. It introduces a paradigm shift by exploring the use of epoxy resin and piezoelectric materials, specifically zinc oxide, in wind turbine blades. The study presents mathematical models and conducts a comparative analysis between conventional and piezoelectric turbines, evaluating efficiency, cost-effectiveness, environmental impact, and energy output differences. While awaiting experimental data, …
Published in Journal of Aerospace Engineering & Technology · Vol. 14, Issue 3, 2024 · pp. 31–42 Read article
-
Acalypha Indica Root Fibre in Polymer Composite: Mechanical Characterization
Abstract: The mechanical characteristics of Acalypha Indica root fibre reinforced epoxy resin composites, including tensile strength, tensile modulus, percentage of elongation, flexural strength, and impact strength, were studied. Composites were fabricated using epoxy glue and randomly oriented fibres of 3 mm length in varying weight ratios of 10%, 20%, 30%, and 40%. The hand layup method was followed by compression moulding to construct the composites. The study aimed to determine the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 512–522 Read article
-
Design and Development of Fiber Sandwiched Composite Materials for the Improvement of Mechanical Properties
Abstract: This research paper presents the development and mechanical characterization of fiber sandwiched composite materials (FSCM) to address the increasing demand for high-strength, lightweight, and corrosion-resistant materials in advanced engineering sectors such as automotive, aerospace, and transportation industries. Traditional homogeneous materials such as metals, ceramics, and polymers often fail to provide a balanced combination of properties like high tensile strength, low density, toughness, abrasion resistance, and impact resistance needed for modern …
Published in Journal of Experimental & Applied Mechanics · Vol. 17, Issue 1, 2026 · pp. 22–37 Read article
-
Nano- Catalysts for Enhanced Performance in Hydrogenation Reactions
Abstract: The development of nano-catalysts has revolutionized the field of hydrogenation reactions, offering unparalleled efficiency and selectivity. This study explores the synthesis, characterization, and application of novel nano-catalysts designed to enhance hydrogenation processes. By leveraging advanced materials science techniques, we have engineered catalysts with precisely controlled particle sizes, shapes, and surface properties. These nano-catalysts exhibit remarkable activity and stability, attributed to their high surface area-to-volume ratios and unique electronic structures. Our …
Published in Journal of Catalyst & Catalysis · Vol. 11, Issue 1, 2024 · pp. 22–27 Read article
-
Hybrid Composite Behavior of Concrete-Filled Steel Tube (CFST) Columns: Review of Collapse Mechanisms and Polymer-Based Enhancements
Abstract: Concrete-Filled Steel Tube (CFST) columns are an advanced hybrid composite system where the steel tube's confinement and the concrete core's load capacity work together to improve structural performance. While commonly used in civil engineering, CFSTs can also be understood within the framework of composite materials, similar to polymer- and fiber-reinforced composites, in which interactions between phases determine strength, ductility, and failure modes. This review compiles experimental and numerical research on …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 78–97 Read article
-
Design and Development of Pedalled Powered Electricity Generation
Abstract: Pedal power energy harvesting transforms the mechanical energy produced by pedalling into electrical energy, which can be used to operate devices or saved for future use. The strategy utilizes the physical exertion of pedalling to generate a reliable and eco-friendly energy source. This project aims to develop, construct, and demonstrate a functional mechanism. The generator utilizes the motion of pedalling a regular bicycle to generate electricity. The main goal of …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 16, Issue 1, 2025 · pp. 30–36 Read article
-
Bonding Strength Characteristics of FRP Cylindrical Composites Under Hygrothermal Loading
Abstract: This study investigates the bonding strength characteristics and stress distribution patterns in fiber-reinforced polymer (FRP) cylindrical composites subjected to hygrothermal loading conditions. A four-phase cylindrical model incorporating AS-Graphite and S-Glass fibers with low modulus epoxy coating was analyzed under four distinct pressure loading conditions (25.984, 38.976, 77.953, and 155.906 MPa). Comprehensive stress analysis revealed significant variations in von-Mises stress, maximum principal stress, and minimum principal stress across fiber, coating, matrix, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 950–967 Read article
-
Replacement of Fine Aggregate in Concrete Using Bakelite Powder: A Review
Abstract: This review explores the feasibility of incorporating Bakelite, a thermosetting synthetic polymer known for its durability, heat resistance, and insulating properties, as a partial replacement for fine aggregate in concrete. The increasing focus on sustainable construction practices has driven interest in utilizing industrial waste materials like Bakelite to reduce environmental pollution while enhancing concrete performance. Bakelite, often discarded as industrial waste, presents an opportunity to improve the mechanical and durability …
Published in Recent Trends in Civil Engineering & Technology · Vol. 15, Issue 1, 2025 · pp. 6–10 Read article
-
Functionally Graded Natural Fibre and SiC-reinforced Polymer Composite: Mechanical Properties
Abstract: Multifunctional materials, also called functionally graded materials (FGMs), are based on natural fibres or fillers and vary in composition and/or microstructure to control functional, structural, or thermal, properties. Functionally graded materials (FGMs) have been created for use in spacecraft, aircraft, and other engineering applications because they can withstand extremely high temperatures. Particle-reinforced FGMs, which make up the majority of FGMs, are made differently depending on their position. The mechanical and …
Published in Journal of Polymer & Composites · Vol. 11, Issue 4, 2023 · pp. 1–14 Read article
-
Application of Game Theory Principles for Opportunistic Routing in MANETS
Abstract: This article explores the application of game theory principles to enhance opportunistic routing in mobile ad hoc networks (MANETs). MANETs are characterized by their dynamic topology, limited resources, and lack of infrastructure, making traditional routing protocols less efficient. Opportunistic routing leverages the mobility of nodes and the broadcast nature of wireless communication to achieve reliable message delivery. However, existing opportunistic routing algorithms may suffer from challenges such as high message …
Published in International Journal of Mobile Computing Technology · Vol. 2, Issue 1, 2024 · pp. 1–8 Read article
-
Toxicological Optimization and Assessment of Buccal Films Containing Felodipine Co-crystals to Enhance Bioavailability
Abstract: The preformulation study of felodipine was carried out and it was found that the drug is poorly water soluble. The co-crystals were prepared using three different co-formers sorbitol, ascorbic acid and oxalic acid. The solublity enhancement was observed in combination with sorbitol compared to other co-formers used. The characterization of co crystals was performed like PXRD, FTIR, SEM Analysis. XRD results indicates the amorphous form of the drug. The co-crystals …
Published in Research and Reviews: A Journal of Toxicology · Vol. 14, Issue 2, 2024 · pp. 10–29 Read article
-
Structure-Property-Process Relationships in BNNS-Modified PEEK Nanocomposites for High-Performance Applications
Abstract: This study reports the design and performance evaluation of boron nitride nanosheet (BNNS)-reinforced polyetheretherketone (PEEK) nanocomposites fabricated using melt compounding and high-temperature Fused Filament Fabrication (FFF). PEEK, a high-performance thermoplastic, was reinforced with BNNS at 0.5–5wt.% to enhance mechanical, thermal, and tribological functionalities for advanced engineering use. Composite filaments were extruded and printed using a modified Bambu Lab FFF printer. Mechanical testing revealed a peak tensile strength of 108 MPa …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 867–888 Read article
-
Performance Evaluation of Kevlar-Sisal-S-Glass Hybrid Composites with Ceramic Fillers for Structural Applications
Abstract: This study examines the mechanical properties of hybrid composite laminates reinforced with Kevlar, sisal, and S-glass fibers, and incorporating ceramic fillers—silicon carbide (SiC) and aluminum oxide (Al2O3)—within an epoxy matrix. The hand lay-up method was utilized to produce the laminates, ensuring a uniform fiber stacking sequence and including 10% filler material. Two composite variations were synthesized: one incorporating SiC and the other Al₂O₃, and both underwent tensile, flexural, hardness, and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 Read article
-
Design and Performance Evaluation of PLA-based Umbrella Wheels for Stair-Climbing Robotic Applications
Abstract: Staircase climbing robots require a complex design capable of navigating various stair configurations. A crucial component of such robots is the wheel mechanism. This paper focuses on the umbrella wheel mechanism and its application in staircase climbing robots. In this study, a PLA–based umbrella wheel structure is developed and fabricated using fused deposition modeling (FDM) for application in stair-climbing robots. The umbrella wheel geometry enables transformation from a circular rolling …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 808–824 Read article
-
Research Paper A Review of Symmetry in Mechanical Systems: Theoretical Systems Foundations and Engineering Applications
Abstract: In mechanical system analysis and design, symmetry is of mechanical systems. This article examines the idea of symmetry in mechanical systems, exploring its mathematical foundations (such as Lie algebras and group theory) and how these ideas help explain the behavior, stability, and control of the system. We explore the applications of symmetry in a range of mechanical systems, from basic mechanical connections to intricate multi-body dynamics, emphasizing the benefits of …
Published in Emerging Trends in Symmetry · Vol. 1, Issue 1, 2025 · pp. 15–19 Read article
-
Investigating the Effect of Rubber as Partial Coarse Aggregate Replacement on Concrete Performance
Abstract: The growing challenge of managing scrap tire waste presents an opportunity for recycling these durable materials into concrete production. This research investigates the mechanical properties of concrete with waste tire rubber chips incorporated as a partial replacement for coarse aggregates at 0%, 5%, 10%, and 15% by volume. The study evaluates workability, compressive strength, and tensile strength, alongside durability assessments in a 5% sulphuric acid solution. Initial findings indicate that …
Published in Journal of Industrial Safety Engineering · Vol. 11, Issue 3, 2024 · pp. 11–17 Read article