Search
74 articles for “optimum performance”
-
Influence of ZycoTherm Dosage on Polymer Modified Bitumen and Marshall Performance of Hydrated Lime Incorporated Warm Mix Bituminous Concrete
Abstract: This study examines the effect of ZycoTherm on PMB 76-10 binder characteristics and the performance of PMB-based Bituminous Concrete (BC) Grade-II prepared at reduced mixing temperatures, with and without hydrated lime. PMB 76-10 was modified with ZycoTherm at dosages of 0.05%, 0.10%, 0.15%, and 0.20% by weight of binder and evaluated using conventional and residue-based tests. Increasing ZycoTherm dosage decreased penetration, while softening point, flash point, and elastic recovery increased, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 256–267 Read article
-
Evaluating the Optimal Alccofine-1203 Replacement Ratio in M20 Grade Concrete
Abstract: The primary objective of this research is to investigate the potential of partially replacing cement with Alccofine 1203 in M20 grade control concrete and to evaluate the resulting effects on the mechanical properties of the concrete. Alccofine 1203, a high-performance mineral admixture known for its ultrafine particle size and high reactivity, was used as a partial cement substitute at varying replacement levels of 5%, 10%, and 15% by weight of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 294–299 Read article
-
Ultrasonic Dispersion of Halloysite Nanotubes for Enhanced Mechanical, Thermal, and Morphological Performance of Epoxy Composites
Abstract: Halloysite nanotube (HNT)-reinforced epoxy nanocomposites were prepared by mixing HNT with bisphenol-A epoxy (LY 556) using ultrasonication, followed by compression molding. HNT contents of 0–5 wt.% were used. The composites were evaluated for tensile strength, flexural strength, Shore D hardness, Izod impact strength, and thermal stability using thermogravimetric analysis (TGA). The fractured tensile surfaces were also examined to understand the failure mechanism and interaction between HNT and the epoxy matrix. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Injection Pressure Optimization for Non-edible Biodiesel Blends in CRDI Engines: A Comparative Study
Abstract: The growing demand for clean and sustainable energy has increased interest in biodiesel produced from non-edible oil sources. These fuels are renewable, biodegradable, and do not compete with food resources. However, the effective use of biodiesel blends in modern diesel engines requires proper control of fuel injection parameters, particularly injection pressure. In common rail direct injection (CRDI) engines, injection pressure strongly influences spray formation, air–fuel mixing, combustion behaviour, and exhaust …
Published in International Journal of Manufacturing and Production Engineering · Vol. 3, Issue 2, 2025 · pp. 24–34 Read article
-
Enhancing Mechanical and Thermal Performance of M30 Concrete with Carbon Fibre Reinforcement
Abstract: This study examines the influence of carbon fibre incorporation on the mechanical properties of M30-grade concrete. A series of experimental investigations were conducted to assess the effects of varying carbon fibre content on compressive, split tensile, and flexural strengths. The results indicate a significant enhancement in mechanical performance with the inclusion of carbon fibres, with the optimum fibre dosage identified as 0.75%. At this content, the concrete achieved a peak …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 252–260 Read article
-
Advanced Collaboration and Project Management Platform
Abstract: The growing dependence of employees on remote and hybrid working modes worldwide has driven a demand for modern collaborative platforms to optimize project management. All organizations are keen on solutions that enhance workflow efficiency, facilitate seamless communications, and boost overall productivity. The study presents an advancement in project management collaboration and aims at finding solutions to meet those demands, using API integration. The study explores the extent to which API …
Published in Journal of Web Engineering & Technology · Vol. 12, Issue 2, 2025 · pp. 11–18 Read article
-
Numerical simulation and Artificial neural network illustration of phase-change material integrated into lattice structures printed in 3D
Abstract: This work examines the phase change material (P.C.M.) deposited in various lattice formations—such as “S.C., B.C.C., and F.C.C”.—at varied characteristics. The test concentrates on comprehending heat transport properties and thermal activity throughout the “melting and solidification processes”. The heater's maximum temperature, P.C.M. “melting and solidification”, and Nusselt number are among the essential factors examined. According to the findings, the heater's maximum temperature drops as porosity increases. Although the Nusselt values …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 175–183 Read article
-
Tri-Band Edge-Cut Rectangular Microstrip Patch Antenna on Composite Substrate for RF Energy Harvesting in IoT Networks
Abstract: The increasing use of Internet of Things devices underscores the pressing need for sustainable energy solutions, since traditional batteries necessitate regular replacement and constrain scalability. Radio frequency energy harvesting is a viable option; nonetheless, antenna design continues to provide a significant problem owing to the requirements for compactness, efficiency, and multi-band functionality. A hybrid composite substrate configuration combining FR4 (εr = 4.3) and RT Duroid (εr = 2.2) is employed …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 867–883 Read article
-
Mechanical Characterization of Green Composite Brake Pads Reinforced with Coconut Shell Waste
Abstract: In the present work, coconut shell powder proposed as a replacement material for the eco-friendly brake linings. The composites for brake pad were developed with other sizes of the coconut shell particles, namely (200 µm, 300 µm, 400 µm and 500 µm) The developed samples were evaluated for morphological, mechanical, physical and worability properties. The SEM micrograph proved that the coconut shell particulates are well dispersed in the composite everywhere …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1636–1648 Read article
-
Influence of Rice Husk Ash and Granite Powder on Strength Properties of Concrete
Abstract: Concrete is the mostly utilised material in the field of Civil Engineering. As its consumption is huge in amount and so the scarcity of the raw materials has become a major issue. The important components of concrete are binding material along with the aggregates. Alternative materials are chosen for the replacement of cement to achieve sustainable concrete. Along with cement replacing materials, reusable wastes are also adopted to utilise in …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 133–138 Read article
-
Potential of Particle Size Mix Ratios of Plantain Ogoni Red with Clay Soil: The Integrity of Adsorbent Performance in AGO Treatment in Fresh Water Environment
Abstract: The research is focus on monitoring the performance of various formulated adsorbent mix ratio of clay soil with some agro-based materials in treatment of contaminated water environment. The agro-based material used was Plantain Ogoni Red (POR) and fresh water environment was used for this research. The agro-based material was processed into different particle sizes of 150 𝜇m, 300 𝜇m, 600 𝜇m and 1.18 mm and the clay soil into fine …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 15, Issue 3, 2024 · pp. 12–25 Read article
-
Sustainable High-Strength Geopolymer Composite Reinforced with Nano-Silica and Basalt Fibers: Mechanical and Microstructural Evaluation
Abstract: Sustainable soil composites (SSC) were formulated by incorporating red earth with varying proportions of bagasse ash (BA) and hydrated lime to enhance geotechnical performance and promote the reuse of agro-industrial waste. Red earth served as the primary structural matrix, BA functioned as a pozzolanic filler, and lime acted as a chemical stabilizer. BA content ranged from 0% to 60%, identifying 10% as the optimum level for significant improvement, and lime …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 1113–1122 Read article
-
Marine Algal Microfiber and Agro-Waste Reinforced Crosslinked Polymer Composites for Sustainable Coastal Materials
Abstract: Crosslinked bio-polymer composites reinforced with marine algal microfibers and agro-waste fillers were fabricated and systematically characterized for sustainable coastal applications. Mechanical testing revealed that tensile strength increased from 18.5 MPa for neat polymer to 25.1 MPa at 20 wt.% reinforcement (~35% improvement), while the flexural modulus improved from 0.72 GPa to 1.02 GPa (~42% increase). Impact strength, however, decreased from 3.8 kJ/m² for neat polymer to 2.9 kJ/m² at 30 …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 210–223 Read article
-
Analysis of the Output Power in Offshore Bladeless Vibrational Wind Turbines
Abstract: This work focuses on studying and analyzing the power generation in offshore bladeless vibrational wind turbines. In previous work, we developed detailed research about the vibrational wind turbine design and configuration; in this new work, we analyze the energy supply from this type of turbine to achieve a better understanding of the behavior and potential of bladeless vibrational wind turbines (BVWT) as an additional power source in offshore wind farms. …
Published in Journal of Offshore Structure and Technology · Vol. 11, Issue 3, 2024 · pp. 12–23 Read article
-
Design and Development of Fiber Sandwiched Composite Materials for the Improvement of Mechanical Properties
Abstract: This research paper presents the development and mechanical characterization of fiber sandwiched composite materials (FSCM) to address the increasing demand for high-strength, lightweight, and corrosion-resistant materials in advanced engineering sectors such as automotive, aerospace, and transportation industries. Traditional homogeneous materials such as metals, ceramics, and polymers often fail to provide a balanced combination of properties like high tensile strength, low density, toughness, abrasion resistance, and impact resistance needed for modern …
Published in Journal of Experimental & Applied Mechanics · Vol. 17, Issue 1, 2026 · pp. 22–37 Read article
-
A Review on Sustainable Utilization of Dimensional Stone Waste as Construction Material
Abstract: The non-biodegradable nature of stone waste enhances the worldwide problem of disposal. A lack of land for waste landfills, increased transportation costs, and other related problems have compelled industries to look for alternative solutions. Depletion of natural resources has also been brought about by the construction industry's excessive use of resources like cement, river sand, and natural aggregates. As a result, the demand for sustainable and commercially feasible alternatives is …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 76–85 Read article
-
Water Chestnut Stem-Derived Biochar Supported AgNPs/AC-CTS-PVA Composite Gel for Wastewater Treatment and Potent Antibacterial Performance
Abstract: In the present study, green and efficient Ag-NPs functionalized activated carbon/chitosan-polyvinyl alcohol (AgNPs/AC-CTS-PVA) composite gel was successfully synthesized using water chestnut stem-derived biochar for wastewater treatment and antibacterial applications. The composite was characterized by FTIR, XRD, SEM-EDX, and TGA analyses, confirming the successful incorporation of crystalline Ag nanoparticles within the polymeric matrix and improved thermal stability. The material was tested regarding the removal of the dye of methylene blue (MB) …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1129–1144 Read article
-
Molecular Transport Kinetics of Non-Polar Solvents Through AGNP Filled EPDM Elastomeric Composites
Abstract: EPDM Based rubber composites can be used in tank and pipe lining works. In these applications one of the major requirements is that the composite must have good fluid permeability and chemical degradation resistances in their working environment. In order to enhance the performance of EPDM rubber to suit these applications, scientists and engineers are trying to develop novel nanocomposites by incorporating nano fillers. In the present work, to ensure …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 993–1006 Read article
-
Comparison of High and Low Temperature Properties of Dual Modified Asphalt Binders with Polyphosphoric Acid and Polymer Modified Bitumen using Rheological Tests
Abstract: The main objective of this study was to investigate the properties of asphalt binder mixtures at both high and low temperatures. To achieve this, two types of admixtures were selected and combined, resulting in a technology known as dual modified asphalt binders. Extreme temperatures during summer and winter can lead to significant issues such as cracking and rutting in asphalt binder pavement. In order to address these problems, a comprehensive …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 23–34 Read article
-
Mechanical and Functional Performance of PET–Kenaf Fiber Hybrid Composites for Domestic Household Applications
Abstract: This research presents a hybrid composite of recycled polyethylene terephthalate (PET) and Kenaf fibers for sustainable household applications. Polyethylene terephthalate from consumer bottles was reinforced with Kenaf fibers at volume fractions of 10–30% and composites were created through compression molding. Mechanical characterization involved tensile, flexural, impact, and hardness testing where appropriate and was standardized according to ASTM standards, while their interfacial interactions were characterized by imaging through SEM. Linear and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1482–1498 Read article