Search
76 articles for “concrete composites”
-
Impact of Composite Materials by Silica Fume and Fly Ash in Cement and Partial Substitution of Fine Aggregate Using Quarry Dust in Steel Fibre Concrete
Abstract: Mineral admixtures can be added to concrete to replace some of the cement, increasing its overall strength. Fly ash (FA) and silica fume (SF) are two often used mineral admixtures. A series of experiments were conducted to investigate the effect of adding varied amounts of fly ash and a consistent amount of silica fume on concrete strength by using the same amount of substitute for cement and the same water-binder …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 139–147 Read article
-
Properties of Concrete with Incorporation of Hybrid Fibers and M-Sand-A Review
Abstract: The construction sector is experiencing rapid growth, resulting in an increasing demand for building materials. Concrete, being the building material that sees the most widespread usage, Concrete, as the most extensively used building material, plays an important part in future breakthroughs and advancements However; to make progress we must also address the problems of global warming and pollution. The construction sector is widely considered to be one of the biggest …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 33–39 Read article
-
Graphene-Derived Reinforced Polymer Composites for Self-Healing and Durability Enhancement in Concrete Structures
Abstract: This study presents a matrix-centric polymer-composite repair binder: an epoxy–polyamide network reinforced with graphene derivatives (GO/rGO, 0.1–1.0 wt%). The polymer drives function via segmental mobility that closes microcracks, while 2D-filler topology densifies the interphase, improves load transfer, and enforces tortuous moisture pathways. Adhesion was high: pull-off (ASTM D4541) reached 13.5 MPa at 2.0 mm displacement; slant-shear (ASTM C882) reached 12.1 MPa at 2.8 mm, with greater deformation capacity (zero stress …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 77–91 Read article
-
Analysis of Steel Chip Fiber Reinforced Composite Dual Pile Under Lateral Load Conditions on Sloping Terrain
Abstract: Pile foundations, in addition to supporting vertical loads from superstructures, are subjected to lateral stresses arising from seismic activities, wind gusts, water currents, and traffic impacts etc. Failure to account for these lateral forces can pose significant risks if the structure is expected to encounter any form of lateral pressure. Previous research has investigated the behavior of individual composite piles under horizontal forces, considering different soil properties, to determine the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 210–220 Read article
-
Service Life Prediction of Concretes Incorporated with Fly Ash and Alccofine with respect to Chloride Ion Penetration
Abstract: Chloride-induced corrosion poses a significant threat to the degradation of reinforced concrete structures, especially in extreme environments such as marine and industrial exposure conditions, where the damage can be particularly severe. This study provides an experimental investigation utilizing three distinct water-binder ratios (0.3, 0.4, and 0.5) applied to three types of concrete mixtures: conventional concrete, concrete blended with 40% fly ash, and concrete blended with 40% fly ash and 2% …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 202–213 Read article
-
Durability Assessment of Geopolymer and OPC Concretes under Chloride and Sulphate Chemical Attack
Abstract: The main problems with durable concrete constructions are attacks by sulphates and chlorides on concrete. The primary objective of this study is to evaluate how the strength properties of concrete are affected by the incorporation of fly ash when exposed to environmental conditions involving sulphate and chloride solutions. In this research, geopolymer concrete (GPC) is utilized as a replacement for conventional ordinary Portland cement (OPC). The concrete composition is prepared …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 202–218 Read article
-
A Review on Effects of Waste Tire Rubber Polymer on Fresh, Mechanical, and Impact Resistance Properties of Rubberized Concrete
Abstract: According to the collective findings of numerous researchers, waste tire rubber has proven to be a valuable addition to concrete, contributing to advancements in construction. Rubber crumb is artificial rubber polymers, such as butadiene rubber (BR). The chemical composition of tire rubber crumb that is discarded can be represented by the combination of (C5H8)n, (C8H8)x-(C4H6)y, (C4H6)n, C, S8, ZnO, and complicated hydrocarbons. Various studies have explored the mechanical and impact …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 469–478 Read article
-
Structure–Property Modeling of Cement-Based Multi-Component Composites Using Ensemble Machine Learning and Explainable Feature Attribution
Abstract: Accurate prediction of compressive strength is central to structure–property optimization, quality control, and sustainability-driven design in cement-based composite materials. Cementitious systems represent heterogeneous multi-phase composites composed of reactive binder matrices and dispersed aggregate phases, whose macroscopic mechanical performance emerges from complex nonlinear interactions among constituents and curing-dependent microstructural evolution. This study develops a data-driven structure–property modeling framework to quantify the nonlinear dependence of compressive strength on multi-component composite composition and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 112–131 Read article
-
A Comprehensive Examination of the Compressive Test Results of Concrete Formulations Modified by The Insertion of Ceramic Powder and High-Density Polyethylene Illustrates Nuanced Changes in the Structural Performance Attributes of the Resultant Composite Materials
Abstract: It is becoming crucial to transition from a traditional, utilization-based society to a sustainable one, resulting of the decline in the natural environment, depletion of natural resources, and decreased capacity for final waste disposal. As the populatio grows, so will the demand for concrete. The major goal of this research is to look at the possible technical benefits of using extruded recycled high-density-polyethylene (HDPE) fibers into structural concrete. The mechanical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 193–205 Read article
-
Analytical Study of Concrete-encased Steel Column Building against Blast Load
Abstract: Study of behavior of composite building with Concrete-Encased Steel (CES) columns for blast loading is done. This is compared with the behavior of conventional building having reinforced concrete (RC) columns. In the following study, both composite and RC buildings are subjected to 0.1 ton, 0.3 ton and 0.5 ton TNT equivalent charge weight of blast load with a standoff distance of 20 m, 30 m and 40 m. To study …
Published in Journal of Structural Engineering and Management Read article
-
Sustainable High-Strength Geopolymer Composite Reinforced with Nano-Silica and Basalt Fibers: Mechanical and Microstructural Evaluation
Abstract: Sustainable soil composites (SSC) were formulated by incorporating red earth with varying proportions of bagasse ash (BA) and hydrated lime to enhance geotechnical performance and promote the reuse of agro-industrial waste. Red earth served as the primary structural matrix, BA functioned as a pozzolanic filler, and lime acted as a chemical stabilizer. BA content ranged from 0% to 60%, identifying 10% as the optimum level for significant improvement, and lime …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 1113–1122 Read article
-
An Experimental Investigation of High Performance by Using Steel and Polypropylene Fibres
Abstract: This study explores the feasibility of partially substituting conventional cement in concrete with steel and polypropylene fibers to improve mechanical performance and introduce alternative composite materials. Concrete cube specimens measuring 150 × 150 × 150 mm were cast with varying mix designs corresponding to M20 and M25 grades. The experimental program was executed in two distinct phases. In Phase I, control mixes of M20 and M25 grade concrete were prepared …
Published in Recent Trends in Civil Engineering & Technology · Vol. 15, Issue 3, 2025 · pp. 7–13 Read article
-
A Comprehensive Survey of Structural Applications for Concrete-Filled Steel Tubes
Abstract: A composite section made from a hollow steel tube after concrete has been poured inside of it is known as Concrete filled steel tube. CFT is a high-performance component that combines the impact of steel confinement with the design freedom of concrete. It resists applied stress by fusing concrete and steel. The interaction of steel tubes and concrete gives CFST its strength, and as a result, it has become more …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 184–196 Read article
-
Study on Fiber Reinforced Composite Material Cost in Construction Project
Abstract: The primary goal of this research paper is to identify the major causes of fibre reinforced composite material cost overruns in Indian construction projects, as well as the critical success factors that aid in the avoidance of such costs. The critical success factors is reviewed by existing literature. They are used to generate survey and interview questions. The fiber reinforced materials projects using proposed hypothesis and lack of certain critical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 459–466 Read article
-
Development and Performance Evaluation of Polymer-Modified Geopolymer Composites Incorporating GGBS
Abstract: This research investigates the development and performance of geopolymer-based composite materials formulated using Ground Granulated Blast Furnace Slag (GGBS) as a reactive mineral component within an aluminosilicate polymer matrix. The study aims to create an eco-efficient and structurally sound inorganic polymer composite comparable to M35-grade concrete, produced entirely under ambient curing conditions. A series of mixes with varying GGBS replacement ratios (0–100%) was prepared, maintaining a constant binder content of …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1145–1165 Read article
-
Experimental Research on the Strength Properties of Concrete with Recycled Aggregate, Pond Ash, and Rubber Powder Replaced in Part for Concrete Materials in Standard Grades
Abstract: Concrete, a fundamental material in modern construction, poses environmental concerns due to its significant carbon footprint. To mitigate this impact, researchers explore alternative materials like fly ash, GGBS, alcofine, and rubber powder as cement replacements. This study examines the durability and strength of concrete that contains recycled aggregate, pond ash, and waste rubber powder. Waste rubber, abundant from industrial and automotive sources, poses disposal challenges. Pond ash, a byproduct of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 11–21 Read article
-
An Experimental Investigation of Impact of Polyproplene as a Partial Replacement in Concrete
Abstract: India, as a developing nation, will require high-strength and high-performance concrete for future infrastructure projects. Fibrous concrete, which incorporates fibers to enhance structural integrity, is one such material that could meet these demands. With different concrete fibrous materials, shapes, distributions, orientations, and densities, fibrous concrete takes on different characteristics. Polypropylene is a lightweight synthetic fiber that enhances the structural strength of concrete and helps prevent the formation of cracks. In …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 3, 2024 · pp. 1–6 Read article
-
Characterization of Nano-Clay Reinforced Polymer Composites: Enhancing Performance for Extreme Applications
Abstract: This study investigates the mechanical, thermal, water absorption, and chemical resistance properties of nano-clay-reinforced polymer composites and polymer concrete. The incorporation of 1-5 wt% nano-clay resulted in a significant enhancement across all properties. Mechanical testing revealed a 42.86% increase in tensile strength (35 MPa to 50 MPa), 40% improvement in flexural strength (50 MPa to 70 MPa), and 46.67% rise in compressive strength (75 MPa to 110 MPa), attributed to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 105–114 Read article
-
Utilization of Treated Textile Dyeing Wastewater and GGBFS–Perlite Blends for Sustainable Cementitious Composite Development
Abstract: The increasing global demand for concrete critically intensifies the consumption of potable water, raising significant environmental concerns and depleting vital resources. Concurrently, the textile dyeing industry generates substantial volumes of wastewater, posing considerable disposal and pollution challenges. Our investigation explores a dual solution by utilizing treated textile dyeing wastewater as an alternative mixing water source, combined with ground granulated blast furnace slag (GGBFS) and perlite as supplementary cementitious materials (SCMs), …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 291–300 Read article
-
Sustainability and Mechanical Performance Evaluation of Cementitious Composites Reinforced with Waste Rubber Aggregates and Ground Granulated Blast Furnace Slag
Abstract: The development of environmentally responsible composite materials has gained global momentum with the shift toward circular and sustainable construction practices. In this work, the performance of cementitious composites that partially substitute natural fine and coarse aggregates with recycled rubber aggregates from end-of-life tires and Ground Granulated Blast Furnace Slag (GGBS) as an additional cementitious material is examined. A total of thirty composite mixes were formulated by varying GGBS (10–30%) and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1164–1180 Read article