Search
323 articles for “Compression Testing”
-
Fused Deposition Modelling-based 3D Printing: A Systematic Literature Review Employing VOS Viewer
Abstract: Fused Deposition Modelling, also known as FDM, has emerged as a major technology in the field of 3D printing. It provides adaptability and cost-effectiveness in the process of materializing intricate designs. This paper intends to conduct a complete bibliometric analysis (BA) of 3D printing based on fused deposition modelling (FDM) in order to comprehend the trend and research field. After extracting data from the Scopus database using the titles, abstracts, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 12, 2023 · pp. 197–202 Read article
-
Effect of Solutionizing and Ageing on Mechanical Properties of AL2024 Reinforced Alumina Particulate
Abstract: AbstractAluminium 2024 alloy is widely used at automobile and aircraft industries in the form of cast component with varying section size. This study investigates how the microstructure and mechanical properties of AL2024 alloy before and after heat treatment processes. Solution sing at 493°C-5H followed quenching in water at room temperature. Stir casting method is followed to obtain the required composite material with proper mixing of reinforcement. Further, the mechanical properties …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 3, 2018 · pp. 8–12 Read article
-
Study of High Strength Fiber Reinforced Metakaolin Concrete under Flexure and SplitTensile Strength
Abstract: An experimental investigation was carried out to study the effect of inclusion of metakaolin and steel fibers on high strength concrete in flexure and split tensile strength. The beams of 150x150x700 mm were casted. M60 grade of concrete was used. Superplasticizers were used to improve workability. The metakolin was added upto 20% with the increments of 5% and steel fibers were added upto 5% with the increment of 0.5%. Various …
Published in Journal of Structural Engineering and Management · Vol. 3, Issue 2, 2016 · pp. 70–80 Read article
-
Survey of System-on-Chip Modular Test Approach
Abstract: The advancement in semiconductor technology over the past few decades has enabled the industry to develop new design and reuse methodologies referred as System-on-chip (SoC) design. These typically integrate heterogeneous mix of various complex analog and digital cores, with all their necessary electronic circuitry. The recent advancements have led to the use of the 3D structures (3D-SOCs) that brought along the benefits of higher performance, minimum average interconnect length, reduced …
Published in Journal of VLSI Design Tools and Technology · Vol. 6, Issue 3, 2016 · pp. 56–70 Read article
-
Effect of Polymer Modified Fibers on Strength of Concrete
Abstract: AbstractThe results of an experimental investigation to study the effects of hooked steel fibers with varying dosage and polymer latex with fixed dosage in concrete are studied. In this experimental study, varying volume fraction of hooked steel fibers from 0% to 7% by weight of cement at the interval of 1% of fiber and SBR latex polymer of fixed volume of 15% by weight of cement were used. All specimens …
Published in Journal of Polymer & Composites · Vol. 3, Issue 1, 2015 · pp. 15–24 Read article
-
Estimation of Mechanical Properties of Kevlar/Basalt Intrawoven Composite Laminates Containing Nanoparticles
Abstract: Purpose: The research describes estimation of various Mechanical properties like compression, tensile, shear and impact strength of Kevlar/Basalt (KB) Intrawoven 1×1 composite laminates, each comprising 1%, 3% and 5% of Al2O3 (Aluminium oxide) nanoparticles. Design/methodology/approach: These are woven with the help of manual handloom weaving machine, compression moulding technique was adopted for the fabrication of hybrid composite laminates. Attempts have been made to analyse the mechanical properties of Kevlar/Basalt intrawoven …
Published in Journal of Polymer & Composites · Vol. 11, Issue 2, 2023 · pp. 1–12 Read article
-
Liquefaction Behavior of Clean Sand for Various Sample Sizes Using Triaxial Tests
Abstract: A total of 54 isotropically consolidated un-drained triaxial compression tests on various sample sizes were conducted to study the effect of sample size on liquefaction behavior of clean sand. Specimens were prepared using moist placement and dry deposition methods with different initial relative densities and tested for different confining pressures. It was observed that as the sample size increases, deviator stress also increases. Peak value of deviator stress increased as …
Published in Recent Trends in Civil Engineering & Technology · Vol. 4, Issue 2, 2014 · pp. 22–29 Read article
-
Mechanical Behaviour of Conventional Concrete Using Fly Ash and Steel Fibre
Abstract: Concrete that area unit victimization with the waste materials, recycled materials etc. could be a revolutionary topic at this time of concrete business. This kind of concrete that resembles the traditional concrete, however the assembly or utilization of such concrete needs minimum quantity of energy and causes least hurt to atmosphere. This kind of concrete absorbs the waste product that is additionally useful for atmosphere aspects [1]. Some SCMs area …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 1, 2017 · pp. 18–23 Read article
-
Comparison of Index and Engineering properties of weak soils stabilized by Rubber Tyre Chips and Powder
Abstract: Engineered constructions on weak or soft ground soil carry inherent risks due to the instability of the foundation. Soft ground lacks the necessary strength to support structures adequately, making it prone to settlement, subsidence, or even collapse under the weight of buildings or infrastructure. Various methods of improvements are used to improve the soil's stability to support various loads.one of the solution is can use the waste products incorporated into …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 24–33 Read article
-
Experimental Investigation of Plastic mix Concrete for Pavement Quality Concrete (PQC)
Abstract: ABSTRACT: This project is particularly dealt with the possibility and analysis of using waste Polyethylene Terephthalate (PET) in M40 grade of concrete (from IRC 44) as a partial replacement of fine aggregate with varying percentage of 0%, 2.5%, 7.5%, 12.5%. Various tests performed on cement-like specific gravity, fineness, setting time, standard consistency, etc. on coarse aggregate such as sieve analysis, fineness modulus, specific gravity, etc. On fresh concrete-like slump cone …
Published in Recent Trends in Civil Engineering & Technology · Vol. 10, Issue 2, 2020 · pp. 30–37 Read article
-
Standardization of Cement Mortar by Using GGBS for Plaster Work
Abstract: This study investigates the feasibility of using replacement of natural river sand with 100% crushed sand, and partial replacement of cement with optimum percentage of ground granulated blast furnace slag (GGBS) on site conditions with a proportioned water cement ratio for plaster work. The methodology, which it undergoes, is slump test, compressive strength, flexural strength, split tensile strength. Cubes (70.6 mm 70.6 mm), beams (160 mm 40 mm), …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 23–29 Read article
-
Experimental Investigation on the Seismic Disaster Mitigation of Unreinforced Brick Masonry Buildings
Abstract: The Himalayan region is considered to have the potential to produce earthquakes of magnitude 8.0 or greater once every 100 years. Since the occurrence of an earthquake cannot be prevented; therefore, seismic disaster mitigation remains the only option for the civil society. Unreinforced masonry (URM) buildings, constructed with stone or brick, are very common in Northern Pakistan part of Himalayan belt. The seismic performance of stone masonry was found very …
Published in Recent Trends in Civil Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 55–67 Read article
-
Optimization of Polymer-Enhanced Sustainable Concrete: A Composite Approach with Bentonite and Crumb Rubber Aggregates
Abstract: The disposal of rubber tyres has become challenging; on the other hand, the utilization of rubber tyres is also increasing daily in society. The successful use of crumb rubber as an alternative aggregate and bentonite as a partial cement replacement in concrete composites has been well established through prior research. These materials have individually demonstrated their potential to enhance sustainability, improve concrete properties, and reduce environmental impact, paving the way …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 701–715 Read article
-
Effect of Surface Pore Filling and Adhesive Joining on Energy Absorption of Closed Cell Aluminum Foam
Abstract: The joining of aluminum foam is explored in this paper. Foam specimens were sectioned and joined with commercially available adhesive and tested for its energy absorption capability against a normal foam specimen. There was a decrease in the plateau stress but the decrease is not significant. The effect of surface pore filling by the adhesive was also realized. It was found that the adhesive in the surface cells introduces constraints …
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 117–124 Read article
-
Tailoring the Compressive Behavior of Tetrachiral Auxetic Structures Through FDM Process-Parameters
Abstract: This research evaluates how fused deposition modeling (FDM) fabrication process parameters affect the compressive behavior of tetrachiral auxetic structures created from Polylactic Acid (PLA). Auxetic materials have several useful properties, including reversible deformation and high-energy absorbing capabilities, which are beneficial to creating ultra-lightweight structural, protective, and shock-resistance designs. Among the available auxetic topologies, the tetrachiral configuration is particularly attractive for engineering use, because its rotation-dominated node–ligament deformation gives a negative …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 · pp. 58–70 Read article
-
Effects of Polypropylene Fibre on Strength of Geopolymer Concrete
Abstract: In the construction industry, the most vital parameter considered in the current scenario is the sustainable development of the structures. The most used material in construction is concrete, which is primarily made up of Portland cement. The production of Portland cement is nearly about 2.6 billion tonnes per year and is increasing at the rate of 5% annually. The concrete industry contributes about 5–8% of all human generated carbon dioxide …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 3, 2016 · pp. 23–31 Read article
-
Dynamic deformation and microstructural characteristics of AA5083 under the influence of electrochemical behaviour using equal channel angular pressing
Abstract: Large-scale Equal channel angular pressing is a great engineering material that has more potential for AA5083 industrial applications. Uniaxial dynamic compressive tests across a temperature of 448 K were conducted for the ECAP technique AA5083 in order to create such a design framework. The microstructure was described using transmission electron microscopy and scanning electron microscope both before and after dynamic loading. The plastic flow behaviour of the AA5083 was described …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 95–112 Read article
-
Comparative Analysis of Eco Friendly Brick with Red Bricks
Abstract: This research presents a comparative analysis between conventional red bricks and eco-friendly bricks made from mud, rice husk, and dry plant leaves. The aim is to evaluate the potential of using sustainable, low-cost, and locally available agricultural waste materials in brick production as an environmentally conscious alternative to traditional methods. The eco-bricks were manufactured without kiln firing, significantly reducing energy consumption and carbon emissions. A series of laboratory tests—including compressive …
Published in Journal of Structural Engineering and Management · Vol. 12, Issue 3, 2025 · pp. 42–46 Read article
-
Design and Analysis of Honeycomb Rear Door Map Pocket by Application of Finite Element Method
Abstract: In modern automobiles, the door trim plays a vital role in both functionality and occupant safety. It integrates various convenience features such as armrests, power window switches, and map pockets, while also contributing to crash energy absorption during side impacts. In such collisions, the occupant's body typically contacts the door trim, making its design and material selection critical for minimizing injury through controlled deformation and energy dissipation. This research focuses …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 940–951 Read article
-
Mechanical Characterization of Green Composite Brake Pads Reinforced with Coconut Shell Waste
Abstract: In the present work, coconut shell powder proposed as a replacement material for the eco-friendly brake linings. The composites for brake pad were developed with other sizes of the coconut shell particles, namely (200 µm, 300 µm, 400 µm and 500 µm) The developed samples were evaluated for morphological, mechanical, physical and worability properties. The SEM micrograph proved that the coconut shell particulates are well dispersed in the composite everywhere …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1636–1648 Read article