Search
1936 articles for “CO” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
The Effects of Physiochemical Parameters and Microbial Counts on Metal Coupons Corrosions in Freshwater Environment at Different Water Depths
Abstract: The effect of water quality on metal coupon corrosion was investigated at the New Calabar River in Choba. The study examined metal corrosion rates at five different depths: 30 cm, 60 cm, 90 cm, 120 cm, and 150 cm in a freshwater environment. Water samples were collected at each depth and analyzed for physicochemical and microbial parameters to understand their impact on metal degradation. Key parameters measured included pH, Electrical …
Published in Journal of Water Pollution & Purification Research · Vol. 12, Issue 2, 2025 · pp. 31–51 Read article
-
Corrugated Tube Shell-and-Tube Heat Exchanger Using Epoxy-Based Polymer Composite Coatings for Lightweight and Efficient Thermal Systems
Abstract: Corrugated tube geometries are widely recognized for their ability to enhance heat transfer through boundary layer disruption and secondary flow generation. In this study, a combined experimental and computational investigation is carried out to evaluate the thermo-hydraulic performance of a shell-and-tube heat exchanger incorporating corrugated stainless steel tubes integrated with an epoxy-based polymer composite coating and housed within a mild steel shell. Unlike conventional metallic systems, the present work introduces …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 603–617 Read article
-
Polymer Composite-Supported Jackfruit Peel Adsorbent for Enhanced Copper (II) Removal from Wastewater: Batch Equilibrium and Isotherm Analysis
Abstract: The increasing concern of disposal of copper-containing effluents into the environment has led to heightened interest in designing cost-effective, eco-friendly and scalable adsorbent systems. Traditional metals and synthetically engineered sorbents prove to be effective; however, these systems are energy intensive. Agricultural residues entrapped in polymer composite systems constitute an economically feasible solution to this environmental challenge. This work reports on the design, characterization and performance evaluation of an economical adsorbent …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 375–390 Read article
-
Comparison Between Reed–Solomon and BCH Code with Various Modulation Schemes Over Coding Gain and Coding Rate
Abstract: The main objective of this research paper is to make a comparison between the performance of Reed-Solomon (RS) and Bose–Chaudhuri–Hocquenghem (BCH) codes across different modulation schemes concerning coding gain and coding rate within an additive white Gaussian noise (AWGN) channel system, while maintaining a constant transmission bandwidth. In this paper bit error rate (BER) versus signal/noise (S/N) performance of a Simulink model is validated with MATLAB results for a RS …
Published in Research & Reviews: A Journal of Embedded System & Applications · Vol. 12, Issue 1, 2024 · pp. 32–50 Read article
-
Comparative Analysis on Concrete Strength Using Various Sizes of Aggregates and Combined Gradation
Abstract: This research delves into the effect of using various single coarse aggregate sizes and combinations of such by specific proportions. A thorough examination involving control specimens of 12mm, 20mm, and 25mm aggregates sizes, with combining proportions in the ratios – 5/8:3/8, 1/2:1/2, 3/8:5/8 have been conducted, shedding light on critical patterns that dictate concrete performance. The fine aggregate was properly zoned from the preliminary test. The design mix was calculated …
Published in Recent Trends in Civil Engineering & Technology · Vol. 14, Issue 1, 2024 · pp. 29–36 Read article
-
Numerical Investigation on Concrete Filled Steel Tube Composite Circular Columns Under General Loading
Abstract: Concrete-filled steel tube (CFST) composite columns are extensively utilized in civil engineering constructions because of their numerous structural advantages, such as superior seismic performance, high load- bearing capacity, fire resistance, remarkable ductility, and ability to absorb energy effectively, especially in areas prone to seismic activity. CFST columns are employed in tall buildings and bridges to enhance rigidity and increase bearing capacity, but their behavior can be affected by buckling. There …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 164–199 Read article
-
Deep Cryogenic Treatment of Copper Chill Plates in Stir Casting of Al6061-Silicon Carbide Composites
Abstract: Aluminum-Silicon Carbide Metal Matrix Composites (Al/SiC MMCs) represent advanced materials created through the integration of aluminum matrices with silicon carbide particle reinforcement. These composites demonstrate superior characteristics compared to conventional aluminum alloys, establishing their relevance across diverse engineering applications. This experimental investigation focuses on developing composites using aluminum as the base matrix while incorporating SiC particles (40-50μm particle size) as reinforcing agents. The reinforcement content was systematically varied from 3 …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 116–126 Read article
-
Parallel and Concurrent Computing with Shell Commands: Exploring CPU Architecture, LAN Interconnection and Command Languages for Green Sustainability
Abstract: Parallel and concurrent computing are essential ways of thinking in the digital age, where the cost indexes are efficiency, speed and sustainability. By far performance relevance of each metaphor Contemporary computational environments covering everything from dumb terminals to distributed workstations and intelligent network systems such as the command-line interface (CLI) can never do well on its performance when throughput is needed most the era's fact that there is no hitting …
Published in Journal of Advances in Shell Programming · Vol. 12, Issue 3, 2025 Read article
-
Polymeric Coating Applied for Corrosion Protection of Mild Steel in Corrosive Medium
Abstract: Mild steel is coated with a polymer layer of polybutadiene for protection. However, this coating does not effectively safeguard the metal in environments containing moisture, sulphur dioxide, or chloride. These pollutants interact with the polybutadiene-coated surface, creating a highly corrosive atmosphere. Moisture condenses on the coated metal surface and absorbs sulphur dioxide, forming sulphuric acid. This acid initiates both chemical and electrochemical reactions with the polymer-coated metal, accelerating the corrosion …
Published in International Journal of Advance in Molecular Engineering · Vol. 3, Issue 2, 2025 · pp. 49–53 Read article
-
Thermo-Fluid Characterization of Corrugated U-Tube Shell-and-Tube Heat Exchanger with Polymer Composite Tube Wall: A Combined CFD and Experimental Investigation
Abstract: Shell-and-tube heat exchangers built with metallic tubes work well thermally, but corrosion problems, extra weight, and the inability to adjust the wall’s thermal properties through material choice remain genuine engineering headaches, particularly for corrosive or weight-critical applications. Over the past few years there has been a fair amount of interest in replacing metal tubes with polymer composite alternatives, since blending thermally conductive fillers — graphite nanoplatelets, boron nitride platelets and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 Read article
-
Conducting an Experimental Study on the Behavior of Concrete Involves Partially Substituting Coarse Aggregate with Waste Granite Tiles and Fine Aggregate with Quartz Sandstone Powder
Abstract: In agricultural nations where cement is generally utilized, the high and consistently inflating cost of cement has made development over the top expensive. Removal of strong waste materials is an extraordinary worry in urban communities from one side of the planet to the other. A portion of these waste materials are not biodegradable, which frequently prompts removal emergency and natural contamination. Numerous endeavors are being made for the reusing of …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 3, 2024 · pp. 26–34 Read article
-
Complex Tuberculous Meningitis: A Case Series Highlighting Rare Co-infections and Severe Complications
Abstract: This case series presents two complex cases of tuberculous meningitis (TBM) with different complications, illustrating the diverse clinical presentations and management challenges of this disease. Case 1 involves an 18-year-old female with TBM complicated by cryptococcal co-infection, while Case 2 describes a 64-year-old female with TBM complicated by obstructive hydrocephalus and secondary bacterial infections. Both patients had been on anti-tubercular therapy before presentation. Diagnostic approaches included cerebrospinal fluid analysis, cultures, …
Published in International Journal of Pathogens · Vol. 1, Issue 2, 2024 · pp. 1–7 Read article
-
Properties of Binary Waste Based Geopolymer Concrete Composite: A Review
Abstract: Concrete composite as construction material is utilized all over the world and it is not considered as eco-friendly because cement is provided as a binder in it. Therefore, replacing binder in concrete composite by alumina and silica rich by-products in presence of chemical activators give rise to geopolymer concrete composite which is eco-friendly in nature. Geopolymer concretes composite can be used to build a variety of structural configurations, have a …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 44–52 Read article
-
Influence of Mechanical Parameters on Corrosion Behavior of Metal Coupons in Simulated Environmental Conditions
Abstract: This study investigates the influence of mechanical parameters—namely applied stress, surface roughness, and deformation history—on the corrosion behavior of metal coupons exposed to corrosive environments. Mild steel and aluminum alloy specimens were prepared with controlled variations in tensile stress, polishing grades, and cold-working levels to simulate real-world mechanical influences. These coupons were immersed in a 3.5% NaCl solution under ambient conditions, and their corrosion rates were monitored over a 30-day …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 6–12 Read article
-
Electroplating and Corrosion Properties of Binary and Ternary Zinc Alloys with Nickel, Cobalt and Iron
Abstract: The anti-corrosive three binary (Zn-Ni, Zn-Co, Zn-Fe) and two ternary (Zn-Ni-Co, Zn-Co-Fe) alloy coating films on mild steel from acid chloride bath using sulphanilic acid and gelatin as additives for the electroplating technique. The normal Hull cell method was used to optimize the bath compositions, temperature and pH of the bath solutions for coating performance against corrosion. The cause of current density (CD) on metal weight percentage (M = Ni, …
Published in Journal of Thin Films, Coating Science Technology & Application Read article
-
Electrochemical Evaluation of Corrosion Behavior in Industrial Alloys Under Acidic and Marine Conditions
Abstract: Corrosion represents a spontaneous physicochemical transformation in which metals revert to their more stable thermodynamic state, typically oxides, hydroxides, or sulfides, as a result of interaction with environmental elements. Rather than being a simple surface reaction, corrosion is a complex electrochemical phenomenon that significantly influences the durability, reliability, and performance of metallic structures across industrial, marine, and domestic sectors. The consequences extend beyond material degradation, contributing to substantial economic losses, …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 13, Issue 1, 2026 · pp. 24–36 Read article
-
(𝛅,Ü ) Convex Structure on Partial B-Metric Space Concerning Quasi Contraction and Fixed-Point Results
Abstract: This work introduces the concept of (δ,Ü )– Convex Partial b-Metric Spaces using convex structure. Motivated by this approach, we demonstrated fixed point results and their uniqueness, as well as quasi contraction, and provided some supporting instances for the established results. Our findings expand prior fixed-point results to a novel concept (δ,Ü )– Convex Partial b-Metric Spaces. To support our theoretical findings, we provide several instances that exemplify the established …
Published in Recent Trends in Mathematics · Vol. 1, Issue 1, 2024 Read article
-
Experimental Analysis of Axially Compressed Precast Concrete Pressure Pipes Filled with Concrete
Abstract: Humanity has always been at the mercy of natural disasters, which frequently result in widespread devastation and displacement. However, scientific advancements, technological innovations, and extensive research have significantly mitigated the loss of life, property, and essential resources. One of the critical challenges in the aftermath of disasters is providing adequate and timely shelter, food, and medicine to the affected populations, often under constrained resources and logistical difficulties. In response to …
Published in Recent Trends in Civil Engineering & Technology · Vol. 15, Issue 1, 2025 · pp. 28–37 Read article
-
Study on Fiber Reinforced Composite Material Cost in Construction Project
Abstract: The primary goal of this research paper is to identify the major causes of fibre reinforced composite material cost overruns in Indian construction projects, as well as the critical success factors that aid in the avoidance of such costs. The critical success factors is reviewed by existing literature. They are used to generate survey and interview questions. The fiber reinforced materials projects using proposed hypothesis and lack of certain critical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 459–466 Read article
-
Structure–Optical Property Correlation of Co-Doped TiO₂ and ZnO Nanofillers for Advanced Functional Composite Applications
Abstract: This study investigates the enhancement of the structural and optical properties of titanium dioxide (TiO₂) and zinc oxide (ZnO) nanoparticles through cobalt (Co) doping. Pristine TiO₂ and ZnO are widely studied metal oxides; however, their large band gaps and limited visible-light absorption restrict their performance in optoelectronic, photocatalytic, and environmental applications. Co doping is employed as an effective strategy to overcome these limitations by inducing band-gap narrowing, creating defect-related electronic …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1374–1394 Read article