Search
1958 articles for “Desi” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
Design of 16-bit Pipelined RISC Processor
Abstract: This paper presents the design of efficient and high throughput 16-bit pipelined RISC Processor. The design is challenge with the pipelined stall problem, speed with external memory, coding density and clock frequency for cost effectiveness and higher performance processor design. Paper describes about the architecture, programming model, synthesis results and analysis of the design. The presented design has throughput ~167 MIPS at 500 MHz, which shows better performance at a …
Published in Journal of VLSI Design Tools and Technology · Vol. 2, Issue 1-2-3, 2012 · pp. 32–37 Read article
-
Low Power RF QPSK MODEM Design
Abstract: System-level simulation including design of CMOS circuits for radio frequency QPSK MODEM targeting applications in 2.45 GHz industrial, scientific and medical (ISM) band has been presented in this paper. Based on the QPSK architecture, the MODEM consists of an analog mixer using a voltage multiplier, a 90 °phase shifter, delay circuits, a voltage adder and a filter to detect the information. A code reuse subsystem block consisting of Chebyshev filter …
Published in Journal of VLSI Design Tools and Technology · Vol. 2, Issue 1-2-3, 2012 · pp. 75–86 Read article
-
Design of A Spillway: A Case Study
Abstract: A hydraulic structure constructed to discharge surplus water from the reservoir into the river on the downstream side without endangering the safety of the dam is known as Spillway. Spillway is very important structure in any dam project. Many dams have failed because of incorrect design of spillway. Spillway is most vulnerable part of dam. Proper attention has to be given to the design and construction of spillway. Spillway can …
Published in Journal of Water Resource Engineering and Management · Vol. 2, Issue 2, 2015 · pp. 19–28 Read article
-
Protection System Design for Power Distribution System in the Presence of Distributed Generation
Abstract: Investigation was carried out on transformer and bus-bar protection of feeder 1,3,4&6 networks of specially two selected Communities in Egi clan of Ogba Kingdom of Ogba/Egbema/Ndoni Local Government Area of Rivers State such as obagi and oboburu communities respectively. Addressing the three aspects in the design of protection system by determining protection device locations, determining protection device settings, coordination and also mathematical modeling of protective device using MATLAB software for …
Published in Recent Trends in Electronics Communication Systems · Vol. 8, Issue 2, 2021 · pp. 1–16 Read article
-
Design and Simulation of Discrete Time Multi-Input Multi-Output Optimal Controller to Control Active and Reactive Power of DFIG
Abstract: The control of active and reactive power of doubly-fed induction generator (DFIG) in a large scale wind farm has become an important issue for the improvement of wind energy system to provide efficient and reliable electrical power with safety. The control strategies of active power and reactive power can be classified in two types—direct power control and indirect power control. First control strategy has designed based on the chosen switching …
Published in Trends in Electrical Engineering · Vol. 5, Issue 1, 2015 · pp. 1–11 Read article
-
A 32-Bit Booth Multiplier Design Using GDI Logic Style
Abstract: Gate diffusion input (GDI) is the newest technology of designing a low-power digital combinational circuit. This logic allows reducing power dissipation, delay and area of any digital logic circuit. The gate diffusion input logic allows implementation of a wide range of any complex logic function. These functions can be realized using only two transistors. This technique is preferred for designing fast using less number of transistors while improving logic level …
Published in Trends in Electrical Engineering · Vol. 5, Issue 3, 2015 · pp. 1–5 Read article
-
Aspect of Power Transformer Design and Optimization
Abstract: Transformer is one of the most important components of power system. Preliminarily it looksa simple device but from analysis and innovative point of view, it is the big bank ofengineering, which comprises civil, mechanical, chemical and electrical engineering. It is thetime of taking challenges and respective solution of minimizing cost of transformer withoutaffecting customer specifications. This is only possible by design optimization process.Optimization is the process of making something better. …
Published in Trends in Electrical Engineering · Vol. 7, Issue 1, 2017 · pp. 8–18 Read article
-
Design of Flour Kneading Machine by using Human Powered Flywheel Motor (HPFM)
Abstract: In present era, flywheel motor is used in various applications extensively and mechanism are powered by human muscle energy. In India, conventionally the flour kneading system works on electric motor or by hand muscle power. These methods are used widely and kneading by hand is time consuming. Some kneading machine is also operated by hand but they are small capacity and time consuming and conventional method by electric motor is …
Published in Trends in Machine design · Vol. 6, Issue 1, 2019 · pp. 19–24 Read article
-
Mathematical Modelling and Comprehensive Review on the Application of Evolutionary Strategies in Design Optimization of Shell and Tube Heat Exchangers
Abstract: This review article presents the application of different evolutionary algorithms which have been utilized for design and optimization of shell and tube heat exchangers in the last decade. The traditional trial and error design approaches can be replaced by such evolutionary algorithms. These evolutionary techniques do not need information of derivatives and hence it can be implemented in various heat exchangers geometry without much complication. Many such EA’s are successfully …
Published in Trends in Mechanical Engineering & Technology · Vol. 7, Issue 3, 2017 · pp. 67–78 Read article
-
DESIGN AND ANALYSIS OF WHEEL RIM
Abstract: Design of wheel rims of the automobiles plays an important role in safety point of view and need more focus in proper designing. Selection of wear and impact resistant materials plays an important role in stability of the wheel rim. The design of wheel rims involves many factors like proper section of material, design shape, supporting ribs etc. It should be strong enough to withstand wear and shock loads at …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 3, 2022 · pp. 1–7 Read article
-
Design of Ultrafast Optical Full Subtractor Link and Performance Analysis
Abstract: AbstractThis article illustrates proposed optical full subtractor schematic through SOA-MZI, yield borrow and difference outputs concurrently. The objective has been accomplished by exploiting nonlinear attributes with SOA. Numerical simulations have been executed and craving optical subtractor output waveforms have been verified at 100 Gbps data rate. Optimization criterion for the design’s performance measurement is taken as Q-factor and the extinction ratio factor. The subtractor output difference and borrow outcomes with …
Published in Trends in Opto-electro & Optical Communication · Vol. 7, Issue 3, 2017 · pp. 7–20 Read article
-
Simulated Design and Characterization of an Efficient Nd:YAG based Solar Pumped Single Mode Laser
Abstract: AbstractAs the current solar pumped lasers have shown to yield a very low efficiency, this research explores the possibility of a simulated design which can be more efficient in converting solar energy into optical power. This paper presents the software design of a Neodymium Doped Yttrium Aluminum Garnet (Nd3+:Y3 Al5 O12) Laser using LASCAD and also presents the characterization of the design using a theoretical mathematical model. Overall, results of …
Published in Trends in Opto-electro & Optical Communication · Vol. 5, Issue 3, 2015 · pp. 39–49 Read article
-
Effects of Variation of Differential Gain and Injection Current on the Performance Characteristics of the Designed 405 nm MQW Violet Laser
Abstract: AbstractIn this work the Designing and Performance Analysis of a 405 nm InGaN based multi quantum well (MQW) Violet Laser have been presented. The internal designing of 405nm Violet Laser has been done with appropriate calculation. The desired wavelength of 405nm was obtained by adjusting the exact concentration of In0.0979Ga0.9021N / Al0.07Ga0.93N. The effects on Rate Equations by varying the differential gain and Injection current have been observed. Also the …
Published in Trends in Opto-electro & Optical Communication · Vol. 4, Issue 1, 2014 · pp. 13–22 Read article
-
A Novel Approach to Design Underground Fault Locator in Power Cable
Abstract: AbstractIt is very difficult to find the exact location of cable fault in underground cables; generally, these problems occur in metropolitan cities. A large amount of money is invested in digging the earth. This problem leads to design this project to find out the exact location of the error occurs in the underground cables from the side of the feeder and liquid crystal display show the distance in kilometer and …
Published in Trends in Opto-electro & Optical Communication · Vol. 10, Issue 1, 2020 · pp. 31–35 Read article
-
A Review: Application of Ant Algorithm in Transport Network Design Problems
Abstract: A dependable and reliable information source for transportation route planning and ready response to traveler demand, have become a hot topic of research these days. Transportation route planning, analysis and processing of traveler demand are among most important factors affecting response to traveler demand. Because of highly dynamic networks and frequent discontinuity, it is desirable to establish routes for fast delivery of people and goods, having a low probability of …
Published in Trends in Transport Engineering and Applications · Vol. 3, Issue 3, 2016 · pp. 17–22 Read article
-
Integrated engineering on design, development and operation of a Table Top Tokamak for Plasma experiments
Abstract: Making of a Table Top Tokamak is having the acute need for conducting various plasma experimental studies. As pulsed devices, small tokamaks come as handy solutions for plasma experimentalists to study the characteristic behavior of plasma at various operating conditions. In addition, it is a challenge to build a Tokamak from its conceptual design. In this paper, details are brought out for a single mode approach that is required to …
Published in Trends in Machine design · Vol. 5, Issue 2, 2018 · pp. 54–62 Read article
-
Design of C-Frame for Assembly of Mechanical Power Press
Abstract: The aim is to generate the model for assembly operation known as mechanical press machine. Using the concept of reverse engineering, the C-frame has been designed considering stress distribution, deflection, and design specification. Thus, a reciprocating piston is used which apply force upon component with the help of a special tool mounted on the piston. The optimum objective of this study is to observe the finite element modeling of ‘C’ …
Published in Trends in Machine design · Vol. 3, Issue 1, 2016 · pp. 24–29 Read article
-
Design and Performance Analysis of a Compact Ultra-Wide Band Textile Antenna on Jeans Material and Bending Consequences
Abstract: This paper presents a novel design of a compact Ultra-wide band textile antenna which operates from the frequency range of 2.8–14 GHz, covering the entire ultra-wide band frequency range of 3.1–10.6 GHz, as approved by FCC. Hybrid design technique is applied to a simplified circular patch design and finally an octagonal shape is achieved that exhibits ultra-wide band characteristics. The substrate of the designed antenna is made of jeans fabric …
Published in Recent Trends in Electronics Communication Systems · Vol. 1, Issue 2, 2014 · pp. 1–8 Read article
-
Design and Fabrication of Automated Rice Huller
Abstract: This paper describes the detailed procedure for design and fabrication of rice huller machine. A rice huller or rice husker is an agricultural machine used to automate the process of removing the chaff (the outer husks) of grains of rice. Throughout history, there have been numerous techniques to hull rice. Traditionally, it would be pounded using some form of mortar and pestle. An early simple machine to do this is …
Published in Trends in Mechanical Engineering & Technology · Vol. 5, Issue 2, 2015 · pp. 34–38 Read article
-
Design and Analysis of Pressure Vessel Pan (shell) of Conventional Jacket Type
Abstract: Pressure vessels are leak proof containers, as the name implies, their main purpose is to contain a given medium under pressure and temperature. Pressure vessels are commonly used in industry to carry both liquid and gases under required pressure and temperature limit. This pressure and temperature comes from an external source or by the application of heat from a direct or indirect source or any combination of them. This project …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 8, Issue 1, 2017 · pp. 26–31 Read article