Search
1034 articles for “performance parameters”
-
Particle Size Effect on the Physicochemical Parameters of Water Media in Treatment of Contaminants of AGO and PMS
Abstract: Some of the physicochemical properties of contaminated water media with AGO and PMS was monitored upon the particle size effect and mix ratio. The physiochemical parameters monitored are potassium ammonia, iron and manganese concentration upon the performance of the formulated adsorbent immersed in the salt water and fresh water medium. The investigation demonstrates the occurrence of leaching in the process, which shows that some of the parameters adsorbed by the …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 27–36 Read article
-
Design and Development of Electromagnetic Braking System Based on Electromagnetic Induction and Eddy Current
Abstract: In this paper, electromagnetic braking system has been developed that ensures passenger’s, driver’s and other road user’s safety and comfort. Most of the conventional braking system like mechanical, hydraulic, pneumatic have certain limitations. In mechanical brake, erosion of the mechanical pads is carried out by frictional force and requires periodic replacement of the bearing. Fluid leakage in hydraulic and pneumatic could lead to brake failure and reduces the effectiveness of …
Published in Trends in Machine design · Vol. 9, Issue 3, 2022 · pp. 9–23 Read article
-
Behaviour of Staggered Opening Shear wall in Tall buildings
Abstract: Now a days we are seeing a rapidly increasing the cost of land not only in India even all over the world and also we need to preserve our important agricultural productive land too. All contributed towards both residential and commercial structures growth in vertical direction that is high rise structure. Behavior of these high rise structures especially with shear walls during hazards like earthquake, wind and lateral loads due …
Published in Journal of Construction Engineering, Technology & Management · Vol. 11, Issue 1, 2021 · pp. 35–44 Read article
-
Performance Analysis of DE-QPSK and π/4 QPSK with MRC Receiver over η-µ fading channel
Abstract: This study presents approximate but simple expression for the average symbol error rate of differentially encoded quadrature phase shift keying (DE-QPSK) and π/4 QPSK with Maximal Ratio Combining (MRC) diversity over independent η-µ fading channels. Numerical results demonstrate the error performance for different values of fading parameter µ for Lth order MRC for Format 1 and Format 2. Furthermore, error performance of both modulation techniques has also been analyzed for …
Published in Journal of Communication Engineering & Systems · Vol. 8, Issue 3, 2018 · pp. 53–59 Read article
-
Energetic and Exergetic Investigation on Vapor Compression Refrigeration System Using Ag₂O-R134a Nanofluid as Refrigerant
Abstract: This paper experimentally explored energetic and exergetic performance investigation of VCR System using Ag₂O-R134a Nanofluid as Refrigerant. The integration of silver oxide (Ag₂O) nanoparticles within polymer and composite materials offers promising avenues for enhancing the thermal and physical properties of advanced systems. The energetic and exergetic performance study of VCR were investigated with test parameters including compressor power consumption, cooling capacity, coefficient of performance (COP), discharge temperature, irreversibility in the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 279–287 Read article
-
Experimental Investigation on Machining Characteristics of EN19 Alloy Steel Using CNC Vertical Machining Center
Abstract: In this research work, the detailed experimentation investigation was performed for EN19 steel using milling process on CNC VMC. The experimentation strategy has been planned using Taguchi’s L9 orthogonal array, consisting of three process parameters such as cutting speed, feed rate and depth of cut on material removal rate (MRR) and surface roughness (SR). Two different types of end mill cutters (solid carbide and titanium nitride coated carbide end mill) …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 3, 2018 · pp. 91–101 Read article
-
Improvement of Geometric Tolerances and Mechanical Properties of Aluminum Hybrid Metal Matrix Composites
Abstract: In the field of metal matrix composite materials, there has been a generous thrust towards the development of electrical discharge machining (EDM). In this study, stir casted aluminum hybrid metal matrix composites were successfully machined using EDM by analyzing the input process parameters namely, pulse-on time, peak current, and gap voltage using L27 orthogonal array. The ideal conditions for various output responses such as material removal rate, circularity, and radial …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1583–1592 Read article
-
Optimizing Performance Characteristics, Thermal Stability, and Manufacturing Performance of Polymer Nanocomposites Using Artificial Intelligence
Abstract: Artificial intelligence (AI) has proven an efficient method to optimize the design and manufacture of polymer nanocomposites, allowing the proper prediction of the behavior of the materials and the results of the processing. This work proposes an AI-based framework to enhance the performance characteristics, thermal stability and manufacturing performance of advanced polymer nanocomposites. The input variables of the proposed framework are the material composition, the nanoparticle concentration, the particle size, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Influence of Infill Density on Structural Performance of FDM-Processed PET-G Polymer: Experimental Validation through Quadcopter Flight Testing
Abstract: Polyethylene terephthalate glycol-modified (PET-G) is an amorphous thermoplastic copolymer increasingly adopted in structural applications through fused deposition modeling (FDM). However, the correlation between FDM processing parameters, especially infill density, and mechanical performance of PET-G parts remains inadequately characterized under real-life loading conditions. This study investigates how infill density (10% and 30%, grid pattern) influences the structural integrity of FDM-processed PET-G components, validated experimentally through quadcopter airframe fabrication and flight testing. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 644–656 Read article
-
Optimization of WEDM Process Parameters Using a Hybrid Multi-Criteria Decision Making Approach
Abstract: The effectiveness of the manufactured parts is typically measured by more than one performance characteristics. Hence the manufacturing engineers frequently experience the difficulty in optimizing the multiple responses at a time. The present work is to explore the effect of wire electrical discharge machining (WEDM) process parameters in machining of Aluminum metal matrix composite (AMMC). The multiple performance characteristics of material removal rate (MRR) and surface roughness (Ra) are optimized …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 3, 2018 · pp. 24–30 Read article
-
Performance Analysis of DWT Based OFDM System using SRRC Filter in Mobile Wimax over Fading Environment
Abstract: AbstractWavelets amid its capability to provide simultaneous information in both time and frequency domain, along with minimization of interference and improved bandwidth efficiency, is considered broadly as an efficient approach to replace fast Fourier transform (FFT) in the conventional orthogonal frequency division multiplexing (OFDM) systems. Efficient filter pulses are employed spectrally in such systems in order to mitigate the effect of inter-symbol interference (ISI) as well as satisfy the bandwidth …
Published in Journal of Communication Engineering & Systems · Vol. 7, Issue 1, 2017 · pp. 1–10 Read article
-
Controller Performance Assessment (CPA) of Intelligent Control for Non-linear System
Abstract: The objective of this paper is to design and undertake comparative analysis of classical and intelligentcontrollers for nonlinear system. These controllers are compared based on controller performanceassessment in which the different parameters as overshoot, steady-state error, rise time, settling time,response of reference change and output variance are analyzed. To achieve these objectives, the water tankcontrol problem as nonlinear system has been built in Simulink and implementations traditionally classicalcontroller and advance …
Published in Journal of Control & Instrumentation · Vol. 1, Issue 1-2-3, 2011 · pp. 25–33 Read article
-
Influence of Mechanical Parameters on Corrosion Behavior of Metal Coupons in Simulated Environmental Conditions
Abstract: This study investigates the influence of mechanical parameters—namely applied stress, surface roughness, and deformation history—on the corrosion behavior of metal coupons exposed to corrosive environments. Mild steel and aluminum alloy specimens were prepared with controlled variations in tensile stress, polishing grades, and cold-working levels to simulate real-world mechanical influences. These coupons were immersed in a 3.5% NaCl solution under ambient conditions, and their corrosion rates were monitored over a 30-day …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 6–12 Read article
-
Optimization of Machining Parameters of EN-27 Material Using Wire Electric Discharge Machining (WEDM)
Abstract: The optimization of Wire Electrical Discharge Machining (WEDM) parameters for EN-27 alloy steel, a high-strength material widely utilized in mechanical and structural applications, is the subject of this study's methodical analysis. Due to its hardness and poor machinability by conventional methods, WEDM is preferred for achieving precise dimensional accuracy and surface integrity. The primary objective of this work is to enhance machining performance by identifying optimal process parameters influencing Material …
Published in Journal of Production Research & Management · Vol. 16, Issue 1, 2026 · pp. 32–36 Read article
-
Development of Overall Process Effectiveness for Continuous Flow Line in a Semiautomated Manufacturing System
Abstract: This paper presents Overall Process Effectiveness (OPE), a performance measurement approach in a manufacturing system. OPE evaluates the process parameters of continuous flow production that affect the performance and reliability of the process. Based on the overall equipment effectiveness (OEE) concept, OPE focuses on the evaluation of production processes that involve human and machines. The developed OPE is validated through a case study ininjection molding (IM) industry. OPE plays a …
Published in Journal of Production Research & Management · Vol. 4, Issue 2, 2014 · pp. 43–53 Read article
-
Experimental Investigation on the Seismic Disaster Mitigation of Unreinforced Brick Masonry Buildings
Abstract: The Himalayan region is considered to have the potential to produce earthquakes of magnitude 8.0 or greater once every 100 years. Since the occurrence of an earthquake cannot be prevented; therefore, seismic disaster mitigation remains the only option for the civil society. Unreinforced masonry (URM) buildings, constructed with stone or brick, are very common in Northern Pakistan part of Himalayan belt. The seismic performance of stone masonry was found very …
Published in Recent Trends in Civil Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 55–67 Read article
-
Performance Analysis of 160 Channel WDM System with EDFA Amplifier
Abstract: AbstractErbium Doped Fiber Amplifier (EDFA) amplifiers are popularly used in wavelength division multiplexing (WDM) system to compensate attenuation and dispersion. The performance of EDFA depends on various parameters such as, EDFA length, Er+3 doping concentration, active fiber length, pump power, pumping wavelength etc. This paper analyzed the performance of EDFA with counter pumping and co-pumping varying the EDFA length, pump power and Er+3 doping concentration and optimized the values for …
Published in Trends in Opto-electro & Optical Communication · Vol. 7, Issue 3, 2017 · pp. 25–34 Read article
-
Parametric Investigations of Melt Flow Index for Nylon6-Mica Composite Based Hybrid FDM Filament
Abstract: The development of new hybrid filaments with improved mechanical and thermal properties has been driven by the increasing need for high-performance materials in additive manufacturing. This study explores the parametric investigations of the Melt Flow Index (MFI) for Nylon6-Mica composite-based hybrid Fused Deposition Modeling (FDM) filament. The investigation uses the Taguchi technique to examine how different extrusion temperatures, loads and the percentage of Mica filler affect the MFI, a critical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 165–173 Read article
-
A Hybrid Algorithm for Processor Scheduling Using Game Theory Variants
Abstract: This study proposes a novel hybrid algorithm for processor scheduling in modern operating systems, integrating the strengths of traditional scheduling methods with game theory variants. Traditional schedulers often struggle to adapt to dynamic workload changes, leading to suboptimal performance. Our hybrid approach addresses this by treating processes as "players" in a game, where the "payoff" is CPU time. A base scheduler (e.g., Weighted Fair Queuing, Earliest Deadline First) provides a …
Published in Journal of Operating Systems Development & Trends · Vol. 12, Issue 1, 2025 · pp. 48–56 Read article
-
Analysis of Friction Stir Welding Utilizing ANSYS: A Study Based on Simulation
Abstract: Friction Stir Welding (FSW) represents a sophisticated solid-state welding methodology that has attracted considerable scholarly attention due to its efficacy in amalgamating high-strength, lightweight substrates including aluminium, magnesium, and titanium alloys. FSW enables the fabrication of defect free products with a substantial amount of mechanical and wear properties. The process is highly sensitive to various parameters that significantly influence the quality and strength of the final product. Studies have shown …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 3, Issue 2, 2025 · pp. 62–77 Read article