Search
304 articles for “fabrication methods”
-
AI-Driven Topology Optimization of Woven Fiber-Reinforced Composite Chassis Structures for Electric Vehicles Under Crash Loading
Abstract: The structural design of an electric vehicle (EV) chassis represents a unique engineering challenge to achieve minimal weight while meeting occupants' safety requirements during high-energy crash conditions without compromise to the battery housing's integrity or the geometrical constraints of the electric powertrain package. In this paper, a single framework is proposed to integrate physics-based artificial intelligence (AI) surrogate models using PINNs, CNN-accelerated topology optimization, and FEA to design woven fiber-reinforced …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 72–89 Read article
-
Design of Advanced Microstrip Patch Antenna for Wearable Application
Abstract: AbstractThis paper presents the review on design of wearable microstrip patch antenna at the operating frequency of 2.4 GHz for wearable application. This work presents a method of applying the combinational between wearable electronics and antennas. Textile antennas are the most interesting research. In telecommunications, microstrip patch antenna is increasing in recent years consequently textile antennas are increasingly demanding. Microstrip patch antenna is an ideal choice for integrated into clothes …
Published in Journal of Microwave Engineering and Technologies · Vol. 6, Issue 3, 2019 · pp. 18–22 Read article
-
ML-Driven Defect Detection in Additive Manufacturing of Polymer Composites Using Thermal Imaging
Abstract: Polymer-based flexible biosensors have emerged as a pivotal technology in continuous health monitoring, yet their deployment in real-world settings is often hindered by undetected micro-defects and signal distortion caused during fabrication or usage. Existing diagnostic frameworks typically rely on post-hoc processing or bulky instrumentation, failing to offer scalable, real-time detection during additive manufacturing workflows. This study introduces an end-to-end, thermographic imaging-integrated framework for in-situ defect identification during the additive manufacturing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 201–215 Read article
-
Fabrication and Evaluation of Mechanical Properties of Banana Fiber Reinforced Epoxy Composites
Abstract: Natural fiber reinforced composites are gaining attention in recent days due to eco-friendly nature, sustainability, low cost and easy availability. The natural fibers are enriched with favorable mechanical properties which diversify artificial fibers are bio-degradable, nonhazardous, light weight. In this submission, specimens of the banana fiber reinforced epoxy composites are developed to evaluate the mechanical properties. The composite sample specimens are designated with different fiber orientations using the hand lay-up …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 37–47 Read article
-
QUALITY IMPROVEMENT IN THE FABRICATION OF NUCLEAR VESSEL OF 20MNMONI55 LOW ALLOY STEEL
Abstract: 20MnMoNi55 is very critical material to weld, as the material is grouped into the P3 category according to the ASME Standard, which has lower weldability then other steel. The various parameters affecting the welding of 20MnMoNi55 like Welding current, welding speed, Voltage, Wire feed rate, stick out etc. should be in optimizing range. In this research paper, the attempt has been made to optimize the welding process parameter using Design …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 1, 2018 · pp. 41–48 Read article
-
The Integration of Machine Learning in VLSI IC Design
Abstract: It represents the first use of AI in the domain of integrating circuits, which has been impacted by it. The conventional VLSI design process that is now in use is replaced by this technology. The laborious manual concepts created by people have been replaced with automated design innovations. This development would trigger a profound change in the fields of AI education and hardware computation. With the introduction of contemporary chips, …
Published in Trends in Machine design · Vol. 11, Issue 2, 2024 · pp. 1–8 Read article
-
Tribological Study on SiC+Graphene Reinforced Al319 Composite andOptimization of Stir Casting Parameters
Abstract: The aluminium 319 (Al319) is a commonly used material for fabricating automobile components. Due to continuous friction and vibration, those components are subjected to significant wear. Therefore, it is necessary to improve the wear characteristics of this Al319. Hence, in this study Silicon Carbide (SiC) and Graphene nanoparticles (GNPs) are reinforce to Al319 via electro-magnetic stir casting method to optimize wear characteristics without its affecting mechanical properties. Various proposition of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 105–123 Read article
-
Experimental investigation on non-linearity in understanding large scale fires
Abstract: Fire doesn't spread in a uniform manner it has an unpredictable nature. The pervasive uncertainty associated with large-scale fires has resulted in the irreparable loss of invaluable human lives, natural resources, critical infrastructure, and systems. To combat this significant issue, substantial financial investments are made annually in research endeavours aimed at preventing and mitigating such devastating incidents. These dedicated research efforts strive to develop innovative strategies, cutting-edge technologies, and robust …
Published in Journal of Industrial Safety Engineering · Vol. 10, Issue 1, 2023 · pp. 27–40 Read article
-
Analysis of Parabolically versus Exponentially Tapered Inbuilt Chip-to-Fiber Butt Coupler
Abstract: AbstractThe finite difference beam propagating method (BPM) is one of the most powerful technique to investigate linear and nonlinear lightwave propagation phenomena in axially varying waveguides such as curvilinear directional couplers, branching and combining waveguides, S-shaped bend waveguides, and different types of tapered waveguides. BPM is also quite important for the analysis of ultra short light pulse propagation in optical fibers. To date numerous algorithms for BPM have been proposed …
Published in Journal of Communication Engineering & Systems · Vol. 3, Issue 1, 2013 · pp. 11–15 Read article
-
DESIGN AND FABRICATION OF EFFLUENT TREATMENT PLANT
Abstract: Effluent water treatment plant works by removing sludge and bacteria from wastewater before releasing them into river. Several river basins are closed due to the excessive growth in the agricultural area, semi urbanization as well as in the industrialization. The performance of wastewater treatment plants for the treatment of small waste also does not meet the required standards. Effluent Treatment Plant (ETP) mainly consists of treatment tanks, clarifier, filter press …
Published in Journal of Experimental & Applied Mechanics · Vol. 10, Issue 2, 2019 · pp. 31–35 Read article
-
Design and Development of Lightweight Polymer Composite Manifold Using CF-ABS and GFRP for Aerodynamic Energy Recovery in Electric Vehicles
Abstract: Electric vehicles provide a number of advantages over conventional fuel vehicles due to their low to no emissions. High energy efficiency improves the driving performance of Electric vehicles. However, they have to face certain challenges such as the high purchase cost of batteries and lack of battery charging facilities. The major drawback of an Electric vehicle is to store sufficient energy to run the vehicle for a long time. This …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 1186–1206 Read article
-
A Multiband Microstrip-fed Slot Antenna for ITS/WLAN/WiMAX & IEEE 802.11a Application
Abstract: A microstrip-fed slot antenna for multiband operation is proposed. The antenna is printed on silicon substrate with thickness of 1.6 mm and dielectric constant of 11.9. A simple 50Ω microstrip line is used to excite the antenna. Small rectangular slots are fabricated on substrate to achieve multiband operation of 2.34–2.44, 3.73–3.77, 3.97–4.05, 4.59–4.79, 5.14–5.26, 5.49–5.57, 5.71–5.8 and 5.86–5.95 for lS1 1l ≤ −10dB. The designing has been done in IE3D …
Published in Journal of Electronic Design Technology · Vol. 4, Issue 1, 2013 · pp. 1–4 Read article
-
New trends in Radio Frequency design and making things smaller
Abstract: Recent improvements in wireless communication, the Internet of Things (IoT), and 5G/6G networks have made people want small, powerful radio frequency (RF) equipment. With an emphasis on how developments in materials engineering, circuit architecture, and packaging technologies are redefining RF system integration, this article offers a thorough evaluation of current developments in RF downsizing. System-on-Chip (SoC), System-in-Package (SiP), and Antenna-in-Package (AiP) ideas, which allow tightly integrated RF front-ends with enhanced …
Published in International Journal of Radio Frequency Innovations · Vol. 3, Issue 2, 2025 · pp. 28–34 Read article
-
Assessment of Decellularization Techniques for Fabrication of Tubular Submucosal Scaffolds from Small Intestine for Application in Oesophageal Tissue Engineering
Abstract: In this ground-breaking study, we sought to create superior tubular scaffolds for tissue engineering by utilizing small intestine submucosa (SIS), a remarkable biomaterial with outstanding therapeutic potential. We investigated two standard detergent-perfusion procedures, peracetic acid under perfusion and classic peracetic acid-agitation, to decellularize tubular SIS, with the goal of generating scaffolds with consistent and reliable properties for oesophageal tissue engineering. To assess biocompatibility, we employed metabolic research, microscopy, mechanical tests, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 3, 2023 · pp. 30–38 Read article
-
Prevention of Corrosion in Electronic Articulated Forms
Abstract: This is study of typical corrosion failure in electronics arose from usual methods as galvanic corrosion, electrochemical migration, and bias induced corrosion. Common metals and alloys used in electronic devices are Al, Au, Cu, Ag, Sn, Pb and alloyed forms. Noble metal plated high performance electrical contacts have descriptive issues as high corrosion resistance thereby stable electrical behaviour. Films of metals and alloys constitutive to chip fabrication has detected to …
Published in Research and Reviews : Journal of Computational Biology · Vol. 10, Issue 1, 2021 Read article
-
Polymer-Based Transparent Conductive Composites for Flexible Solar Panel Coatings
Abstract: This study investigates the fabrication and characterization of polymer-based transparent conductive composites (PTCCs) tailored for flexible solar panel coatings using poly(methyl methacrylate) (PMMA) and poly(ethylene terephthalate) (PET) matrices reinforced with silver nanowires (AgNWs), multi-walled carbon nanotubes (MWCNTs), and PEDOT:PSS. The composites were synthesized through a solution blending and doctor-blade casting method followed by post-treatments to enhance interfacial bonding and conductivity. Optical transmittance values above 85% were achieved across all composite …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 99–110 Read article
-
Hexapod Robot Platforms: Applications in Real-world Environments
Abstract: The main goal of this project is to present a fully constructed Hexapod robot with six legs for versatile movement and a wide range of degrees of freedom. While previous studies have focused on mobile robots, recent advancements have led to the development of impressive navigator robots that have practical applications. The Hexapod's multiple legs offer the advantage of easy customization and the ability to perform various gaits, including tripod, …
Published in Journal of Instrumentation Technology & Innovations · Vol. 13, Issue 2, 2023 · pp. 54–64 Read article
-
Design and Fabrication of Rice Seedling Plantation Machine
Abstract: India is agrarian country. Indian economy based on the agricultural field. It is the most important source of employment for the majority of the workforce in the country. About 70% of Indian workforce is engaged with the agricultural field for their livelihood. Among that India is a world highest percent to produce rice, accounting for 20% of all world Rice production. Rice is a more stable food in country. Develop …
Published in Journal of Experimental & Applied Mechanics · Vol. 11, Issue 2, 2020 · pp. 23–29 Read article
-
Characterization and Fabrication of Hybrid Matrix Composites of AZ91E Metal with Distinct Reinforcements of Fly Ash and ZrO2
Abstract: The current work choose the characteristics of (Magnesium composite) AZ91E-ZrO2-Fly ash Hybrid Metal Matrix using the regular analytic system. The chosen materials for this purpose are fly ash and ZrO2 in equivalent load extents, Stir casting uses a vortex technique to produce composite materials. A comprehensive experimental investigation was conducted to assess the performance characteristics of AZ91E-ZrO2-Fly ash during the cold upsetting process. The study involved utilizing AZ91E magnesium alloy …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 Read article
-
Interfacial Bonding Efficiency in Jute-Carbon Fiber Polyester Matrix Composites Evaluated Through Short-Beam Shear and Interlaminar Fracture Toughness Testing
Abstract: The natural Fiber–synthetic Fiber hybrid composites are jute–carbon Fiber hybrid in polyester matrix which could be used in semi-structural applications of automotive, construction and marine industry as an eco-friendly and cost-effective alternative of conventional carbon Fiber reinforced polymer. But the hydrophilic nature of jute Fibers and the relatively inert surface of carbon Fiber’s cause weak bonding at the interface of the polyester matrix, which causes premature delamination, poor interlaminar shear …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 68–80 Read article