Search
1811 articles for “Carrying”
-
Performance Analysis and Emission Study of a C.I. Engine using Butanol, Biodiesel and Diesel Blends
Abstract: Biodiesel, which has been projected as an alternative to diesel fuel, can be made an attractive and viable substitute by use of a non-glyceride type of readily available, renewable and economic resources like acid oil. The production and consumption of biodiesel will increase in future due to ecofriendly, and possibility of use of existing engines of a motor vehicle without the need for major adjustments. Biodiesel and diesel fuel are …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 2, 2018 · pp. 17–22 Read article
-
Design of Centrifugal Fan Impeller and Comparison with Industry Design: A Case Study
Abstract: Fans are one type of turbo machines to deliver a desired amount of volume flow and static/total air pressure. The density, temperature and altitude play a vital role in fan design. Fan design process is complex and an exact simpler direct analytical methods are rarely used by reputed fan designers. An approach is made to identify analytical formulae recommended by Ing Bruno Eck and Frank. P. Bleier and carry on …
Published in Journal of Experimental & Applied Mechanics · Vol. 11, Issue 1, 2020 · pp. 11–15 Read article
-
Metal Oxide Based Thin Film Transistors for Transparent and Flexible Electronics: Critical Review
Abstract: AbstractTransparent and flexible electronics is new emerging research area. Various technologies are available for thin film transistors (TFT). Metal oxide semiconductors are suitable because of their high optical transparency, good electrical performance etc. These devices have advantages of a-Si and organic materials also. Advantages of these devices are low cost, low process complexity and temperature, and large-area scalability and large carrier mobility. In this paper research work is compared. This …
Published in Journal of Electronic Design Technology · Vol. 9, Issue 1, 2018 · pp. 30–40 Read article
-
1-Bit Full Adder's Analysis and Comparison
Abstract: The full adder circuit forms the basis of majority of digital circuits. Improvement in a basic full adder circuit in terms of area, power and delay affect the performance of whole system. It becomes compulsory to investigate and analyze the performance of implementation of full adder circuit in literature, till now. In this paper, a study is carried out to look into performance parameters of full adder circuit using different …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 2, 2015 · pp. 1–6 Read article
-
Evaluation of Diesel Engine Performance Using Neem Oil Methyl Esters and Biogas as an Alternative Source
Abstract: AbstractThe Neem oil methyl ester (NOME) used as a biofuel is produced by transestetrification process with an aim to reduce the viscosity level, fuel economy and less environmental pollution. Further, addition of biogas to the NOME is expected to improve the performance. The objective of study was to evaluate the performance parameters such as Total fuel consumption (TFC), Specific fuel consumption (SFC) and Brake thermal efficiency (BTE). The experiment was …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 8, Issue 1, 2018 · pp. 21–25 Read article
-
Techno-Economic Analysis of Fixed and Single Axis Tracking Systems Using NPV and IRR Methods
Abstract: A low power, low cost, high utility value photovoltaic power generating system has been designed and developed with an intention of catering to the needs of the rural population located in far flung villages or hilly regions where electricity supply is either unavailable or is erratic. The proposed solar photovoltaic system has been subjected to rigorous performance evaluation using the four widely used performance metrics namely, Energy Gain, Panel Efficiency, …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 10, Issue 3, 2020 · pp. 34–45 Read article
-
Modeling Reaction Rate of Dispersion Coefficient and Oxygen Deficit on Nitrobacteria Transport in Onu-Imo River
Abstract: The migration rate of nitrobacteria in the Onu-Imo River was monitored based on some variables that determine the predictive model for such pollution transport. These parameters were factors applied in developing the derived model for the study. The variables were integrated into the system to monitor their various rates of impact on the transport process in the study environment. This was monitored by applying a one-dimensional flow transport system at …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 11, Issue 1, 2021 · pp. 28–41 Read article
-
A REVIEW ON STRUCTURAL DESIGN ANALYSIS AND ENVIRONMENTAL AUDITING OF RAILWAYS
Abstract: In the present time, Indian railway is the major transport medium. It is so efficient, economic, and services are moderate eco-friendly technology. Changes are on the basis of engineering, logistics, time and luxury. The new structure has faced lots of challenges and every day demands led to some changes day to day. In so many years of Indian railway the tracks are challenging and quite tough which carries lots of …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 11, Issue 2, 2021 · pp. 28–39 Read article
-
Effect of Layering of Reinforcement on Bearing Capacity of Shallow Footing Resting on Sand
Abstract: The study was done to investigate the performance of reinforced soil foundation. The construction of reinforced soil foundation has a cost effective alternative to conventional methods. Performance characteristics were improved by using one or more layers of non-woven geotextile placed beneath the footing to create a composite material. The reinforcement in the soil interacts with the soil and is resisted by friction, adhesion or passive / bearing capacity. To study …
Published in Journal of Geotechnical Engineering · Vol. 5, Issue 2, 2018 · pp. 15–19 Read article
-
Bond Behavior of Reinforced Concrete using Artificial Sand with Quarry Dust as Fine Aggregate
Abstract: Reinforced concrete (RC) is most widely used material in the construction industry. Normally natural sand is used as fine aggregate in the production of conventional concrete. Natural sand is obtained from the river bed through mining operation. To fulfill the requirement of construction industry excessive mining of sand from river bed has been carried out. It is causing threat to the natural environment. Hence, Indian government has led down restrictions …
Published in Journal of Geotechnical Engineering · Vol. 3, Issue 1, 2016 · pp. 44–50 Read article
-
First experimental results on “clay and bentonite” mixtures for the waterproofing of a landfill in Northwestern Piedmont Region (NW Italy)
Abstract: We report on experimental results conducted on “clay and bentonite” mixtures for the waterproofing of a tank landfill located in Northwestern Piedmont Region (NW Italy).The geotechnical experimental tests on “clay and bentonite” mixtures were conducted in the laboratory first, with the aim of finding the optimum percentage of granular bentonite to be added to the clay and then, they were carried out in situ, in the tank, on the layer …
Published in Journal of Geotechnical Engineering · Vol. 7, Issue 2, 2020 · pp. 13–17 Read article
-
An Experimental Studyon Behaviourof Piled Raft Foundation
Abstract: Piles in piled raft are often considered as settlement reducers, not load bearing members. Theexperimental study focuses on the behaviour of piled raft foundation subjected to vertical load. The model rafts were made of mild steel plateswith plan dimension 160 mm ×160 mm × 10 mm. The model piles used in this test were non-displacement piles of diameter 10 mm.Three lengths of piles were used in the experiment to represent …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 3, 2014 · pp. 26–34 Read article
-
The Application of Ergonomics in the Work Environment of ICU
Abstract: Ergonomics plays an important role in healthcare sector. Healthcare as a work environment and as an industry presents a unique set of challenges and opportunities for applying ergonomics. Healthcare industry should make its objectives such that the work environment provided is safe, effective and comfortable. The objective of this work is to study the importance of ergonomics in intensive care nursing for safe and healthy work environment. Data was collected …
Published in Journal of Industrial Safety Engineering · Vol. 4, Issue 2, 2017 · pp. 27–33 Read article
-
Consequence Analysis, Vulnerability Mapping and Fuzzy Fault Tree Analysis for a Better Disaster Management in and Around Chemical Industrial Areas
Abstract: Chemical industries are prone to hazards like fire, explosion and toxic gas releases. Qualitative and quantitative hazard analyses are essential for the identification and quantification of the hazards associated with chemical industries. This study presents the results of a consequence analysis carried out to assess the damage potential of the hazardous material storages in an industrial area of central Kerala, India. These results are used for the estimation of individual …
Published in Journal of Industrial Safety Engineering · Vol. 1, Issue 1, 2014 · pp. 12–18 Read article
-
Assessment of Heat Stress and Noise Intensity Level in Workplace Area of the Iron Foundry
Abstract: The aims of this study were to measure the workplace heat stress and noise intensity levels in different sections of the foundries. The study was carried out in a small industrial city of southern peninsular of India, known for cluster of foundry establishments. The heat and noise level were measured in melting, fettling, gas cutting, heat treatment furnace, and administrative sections measuring the dry bulb temperature(TDB °C), wet bulb temperature …
Published in Journal of Industrial Safety Engineering · Vol. 1, Issue 2, 2014 · pp. 13–17 Read article
-
Machinability Studies of Chrome Steel in Turning Operation: An Experimental Investigation
Abstract: Studies on Machinability aspects are important from the standpoint of optimizing the parameters setting during the machining operations. This paper adds value to the knowledge base of machinability aspects. A report on the experimental investigation conducted, to study the effects of machining parameters on Surface Finish and Material Removal Rate (MRR) during the turning operation is presented. The current experimentation was carried out using two grades of chrome steel namely …
Published in Journal of Industrial Safety Engineering · Vol. 3, Issue 2, 2016 · pp. 10–18 Read article
-
Risk, hazards and safety assessment wood industry using job safety analysis
Abstract: This study carried out on a job safety assessment of wood industry. Using the detailed analytical-descriptive survey involving woodworkers, assessment was carried out based on the literature review. In wood industry, the work which performed are manual lifting, forceful gripping, and the hazard like wood dust and hazardous chemicals in all these process, the hazard is reported commonly. The other job like finishing, planning/scraping, hammering arealso done. The Job Safety …
Published in Journal of Industrial Safety Engineering · Vol. 7, Issue 3, 2020 · pp. 8–12 Read article
-
Compact Autonomous Multipurpose IoT BOT
Abstract: AbstractInternet of things (IoT) is widely used in interconnection of physical and other embedded devices, which enables the objects to exchange data. Robotics is the technology which is used to carry out complex series of actions either automatically or command based, guided by an embedded system within it. The proposed work is an integration of IoT with robotics for home automation. First, when the user enters into the house, robot …
Published in Journal of Instrumentation Technology & Innovations · Vol. 8, Issue 1, 2018 · pp. 27–33 Read article
-
Optimizing Fusion Zone Grain Size, Hardness and Tensile Strength of Micro Plasma Arc Welded Titanium (Ti-6Al-4V) Alloy Using Grey Relational Analysis
Abstract: In the present work, Titanium (Ti-6Al-4V) alloy sheet of 0.5 mm thick is butt welded using Micro Plasma Arc Welding. Welding input parameters like peak current, base current, pulse rate and pulse width are considered and output responses like fusion zone grain size, hardness and ultimate tensile strength of the welded joint are considered. Taguchi L25 orthogonal matrix is adopted by considering four factors and five levels of weld input …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 2, 2018 · pp. 21–33 Read article
-
Design and Analysis of Universal Pick and Place for Ring Gear
Abstract: Today is the modern-day world, the need for a more economical and safer means of increasing production in the manufacturing industry is vital. Nowadays replace the ‘human-being’ by a simple machine. In automation with the use of control systems and information-technologies reduce direct interaction between man and machine. Automation brings accuracy, precision, and efficiency. Since automation replaces the human-being. The automation is playing an important role to save human efforts …
Published in Journal of Mechatronics and Automation · Vol. 6, Issue 2, 2019 · pp. 18–35 Read article