Search
47 articles for “Tungsten”
-
Recovery of Tungsten and Copper from Waste Tungsten Copper Borings
Abstract: During the last many years, the unused tungsten and copper alloy from the discarded electric and electronic equipment and industrial scraps are gathering attention as a section of waste. Because of tungsten's many diverse uses, numerous types of scrap were available for recycling by a wide variety of processes. In the present study, tungsten and copper was recovered by leaching process in ammonium hydroxide solution followed by electro winning process. …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 1, 2017 · pp. 1–8 Read article
-
A Technical review on Investigation Of Cutting Conditions On Tool Life And Material Removal Rate In Turning Of T51620 Using Cermet And Tungsten Carbide Insert
Abstract: The performance of turning operation is depend upon the tool life and MRR of the tool material T51620 material is employed in making of dies in different industry. Tungsten carbide is most suitable insert material used for turning of T51620 .but now days industries need higher productivity and includes higher tool life and higher MRR with same parameters so one should compare the tool material with the advance one cermet …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 3, 2022 · pp. 8–17 Read article
-
Experimental Analysis of Aramid Fiber Reinforced with Tungsten Carbide
Abstract: This study investigates the mechanical performance of aramid fiber-reinforced epoxy composites enhanced with varying weight percentages of tungsten carbide (WC) powder as a secondary reinforcement. The composites were fabricated using both the hand lay-up and vacuum bagging techniques to ensure uniform dispersion of materials and quality surface finish. Tungsten carbide particles with an average size of 4 microns were incorporated into the aramid fiber matrix at incremental concentrations of 0%, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 146–157 Read article
-
Comparative Study of Machining Parameters on Electrical Discharge Machining of Inconel 718 using Copper and Copper-Tungsten Electrode
Abstract: The present scenario in all the manufacturing industries is to make a priority list to cope up the challenges imposed by the superior materials like alloys, ceramics and composite materials which have difficulty in machining. In this study, comparison of experimental results which is found by optimization of machining parameters on material removal and tool wear rate along with two different electrodes material such as copper and copper tungsten for …
Published in Trends in Electrical Engineering · Vol. 8, Issue 2, 2018 · pp. 46–53 Read article
-
Modern Trends in Tungsten(VI) Analysis: From Smart Organic Reagents to High-Sensitivity Spectrophotometry
Abstract: The present review focuses on the spectrophotometric determination of tungsten(VI) using a wide range of organic reagents and their derivatives. Organic ligands have gained considerable importance in analytical chemistry due to their strong ability to form stable and highly colored complexes with tungsten(VI), which enhances the sensitivity and selectivity of spectrophotometric analysis. Various chromogenic reagents reported in the literature for tungsten(VI) determination have been critically examined and compared on the …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 17, Issue 2, 2026 · pp. 19–29 Read article
-
Review and analysis of the Programmable Tungsten Inert Gas Welding Machine
Abstract: The purpose of this study is to examine metal inert gas (MIG) and tungsten inert gas (TIG) welding processes. This study focuses on welding defects with various kinds of AISI- 1020 mild steel welding joints when using metal inert gas (MIG) and tungsten inert gas (TIG). The impact of different process variables on mild steel welding was looked into. In this study, the main process parameters were changed, and destructive …
Published in International Journal of Manufacturing and Production Engineering · Vol. 4, Issue 2, 2026 Read article
-
Weldability of Aluminum Alloy Using Pulsed current Tungsten Inert Gas Welding Process forMechanical Properties: A Review
Abstract: In the TIG welding, also known as gas tungsten arc welding, metal components are bonded by applying heat or pressure. Inert gas is used in pulsed current welding to encapsulate the electrodes and weld pools. Tungsten inert gas is used in the complex welding process known as TIG welding. It alternates between amps operating at high and low levels. Here, increasing the current results in improved power production and weld …
Published in Journal of Materials & Metallurgical Engineering · Vol. 14, Issue 1, 2024 · pp. 28–37 Read article
-
Innovative Design and Implementation of PCD-Based Drawing Dies and Tungsten Carbide Molds for Automotive Fastener Manufacturing
Abstract: This study presents an integrated engineering investigation into the design, optimization, and implementation of advanced tungsten carbide and polycrystalline diamond (PCD) tooling technologies within the cold forging and wire drawing processes at Koobesh Kavir Semnan Company, one of Iran’s leading automotive fastener manufacturers. By combining powder metallurgy principles, material flow simulation, and experimental validation, this research introduces a technological advancement that improves productivity, tool longevity, and cost-efficiency in industrial production. …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 16–26 Read article
-
Weldability of Aluminium Alloy Using Tungsten Inert Gas Welding Process for Mechanical Properties: A Review
Abstract: Metal components are joined using heat or pressure in TIG welding, sometimes referred toas Gas Tungsten Arc Welding. Pulsed current welding utilises inert gas for enclose the weld pools and electrodes. The intricate welding procedure known as TIG welding uses tungsten inert gas. It switches and forth between high and low level amps. Here, the weld quality and power output improve when the current is increased. Pulsed current TIG welding …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 1, 2023 · pp. 15–26 Read article
-
Evaluation of Mechanical Behaviour of Tungsten Carbide and Magnesium Reinforced Aluminium Matrix Composites
Abstract: With industries like automotive and aerospace also being more inclined on the lightweight material and strength that is much substantial, the aluminium-based metal matrix composite has become a major focus of interest. This paper examines the influence of addition of tungsten carbide (WC) and magnesium (Mg) particles on the mechanical characteristics of Al6063 aluminium alloy. The crucible casting technique was made in two composite compositions 2.5 percent and 5 percent …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 1–8 Read article
-
Dissimilar Joining Of Aluminium Alloy to Copper Using Tungsten Inert Gas Welding Process
Abstract: Aluminium-copper dissimilar joints are applicable to electrical industry. 2 mm thick aluminium alloys (A1100) sheet is joined to 1 mm thick copper (Cu-DHP) sheet using tungsten inert gas welding (TIG) process. The effect of process parameters like heat input, torch orientation, arc weaving on mechanical properties of the joint are studied. In this combination the molten pool generated by melting of aluminium edge will wet the coppersurface to form a …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 2, 2018 · pp. 15–20 Read article
-
Machine Learning Regression Based Approach for Prediction of the Ultimate Tensile Strength of Tungsten Inert Gas Welded Joints
Abstract: Many leaders in technology education have shown that the main difference between the technical design process and the process of engineering construction analysis and efficiency [1–3]. The engineering analysis phase of the construction process is where the mathematical and scientific models principles are used to help the designer predict the design results. The engineering feasibility phase process is a systematic process that uses structural elements and conditions to allow the …
Published in Trends in Machine design · Vol. 8, Issue 2, 2021 · pp. 1–10 Read article
-
Development of Novel Materials with Photocatalytic Effect
Abstract: For capturing solar energy and for converting it into electric power, it is utmost essential to design materials that can be used for this purpose. Generally, the materials deployed for converting solar energy into electric energy are sensitive to UV-radiation. If the material used for this purpose are sensitive to visible light, it will be the breakthrough research. It has been a challenge to design materials with novelty of being …
Published in International Journal of Photochemistry and Photochemical Research · Vol. 1, Issue 2, 2023 · pp. 25–39 Read article
-
Optimization of Wear and Friction Parameters of Al-WC Composite Using Response Surface Methodology
Abstract: This paper aims to optimize the wear and friction parameters of Al-WC composite using response surface methodology. Initially dry sliding wear test on specimen of Al-0WC, Al-5WC, Al-8WC and Al-11WC composites were performed using pin-on-disc equipment under atmospheric conditions, with the varying parameters of the applied load 80KN and Sliding distance 6700m and the sliding velocity is kept constant of 3.34 m/s. The optimum parameters of wear mass loss and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 9, Issue 3, 2019 · pp. 17–26 Read article
-
Effect of machining parameters on the tool wear in drilling of 3D PF C/C composite
Abstract: Carbon–carbon (C/C) composites are broadly used in aerospace, defence, shipbuilding, chemical, and nuclear industries owing to their high strength-to-weight and stiffness-to-weight ratios. However, they are brittle, anisotropic and non-homogeneous in nature, making them difficult to machine. Incorrect machining parameters can cause defects such as burrs, delamination, and fibre bundles pullout. This paper aims to study the hole surface and tool wear during drilling of 3D pierced fabric (PF) carbon-carbon (C/C) …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 269–281 Read article
-
Fabrication and Mechanical Characterization of Hybrid Metal Matrix Composite Castings
Abstract: This work investigates and addresses the casting of a novel hybrid composite material with tungsten carbide and aluminum-silicate particles mixed at varying weight fraction rates. Production of hybrid composite has some advantages if it is processed by near net shape techniques. The simplest method for dealing with this hybrid composite is the turbulence produced by the vortex agitating technique. The vortex mixing method is used in this study to create …
Published in Journal of Experimental & Applied Mechanics · Vol. 15, Issue 3, 2024 · pp. 32–38 Read article
-
INFLUENCE OF PULSED TIG WELDING PROCESS PARAMETERS ON MECHANICAL PROPERTIES OF ALUMINIUM ALLOY JOINT: A REVIEW
Abstract: The increase use of aluminium alloy in the previous decades in automobile industry have recommended the research towards learning its behaviour in dissimilar condition with application. Pulsed tungsten inert gas (TIG) welding in aluminium alloy is one of the generally utilized method towards manufacturing the car parts. The present work relates to the enhancement of mechanical properties of Aluminium amalgam welds through beat tungsten latent gas (TIG) welding process. Input …
Published in Journal of Industrial Safety Engineering · Vol. 5, Issue 3, 2018 · pp. 13–18 Read article
-
Implications of WC–cobalt Composed Forms Matrix
Abstract: This article summarizes some forms of tungsten carbide in metals under composition. Accumulated ceramic and metal powders produce cement carbide (CC). Systems in these categories are used to manufacture resistive equipment. Cementation method of tungsten carbide is a metallic manner. CC mine drills are applied for any corrosion resistant purposes. Common matrix metals are Co, Ni, Cu, Al, etc. The performance fault from heat-treated assisted oxidation was assessed by the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 10, Issue 3, 2020 · pp. 26–31 Read article
-
Parametric Optimization of TIG Welding Process in Butt Joining of AISI 310 Austenitic Stainless Steel Materials
Abstract: Tungsten inert gas (TIG) welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. Selection of the levels of the input parameters plays a very significant role in determining the quality of a weld joint. The present study is planned to investigate effects of process parameters: welding current, gas flow rate and arc gap on ultimate tensile strength in TIG welding of austenitic stainless …
Published in Journal of Production Research & Management · Vol. 9, Issue 2, 2019 · pp. 12–19 Read article
-
Effect of Process Parameters on TIG Weld-Brazing of Aluminum Alloy to Galvanized Steel
Abstract: AbstractAbility to join aluminum alloy to steel enables weight reduction of automobile bodies. Gas tungsten arc welding (GTAW) process was employed to weld-braze A8011-H14 aluminum alloy to galvanized steel in lap configuration. The influence of heat input on bead formation and joint strength was investigated. The microstructural characterization was carried out using an optical microscope and scanning electron microscope. The chemical composition was analyzed using energy dispersive spectroscopy technique. The …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 3, 2018 · pp. 8–14 Read article