Journal of Polymer & Composites
Volume 10, Issue 3 (2022)
Table of contents
-
Comparison of Bond Strengths of Nano and Microhybrid Flowable Composites for Orthodontic Bonding: An Invitro Study
Abstract: Introduction: When the orthodontic brackets are bonded to the etched enamel, the ideal orthodontic adhesive should have optimal bond strength and be able to withstand masticatory forces as well as orthodontic forces. At the same time, when the treatment is completed, the bracket should debond without causing any damage to the enamel. There have been many recent advances in composites in general and their applications in orthodontic use is questionable. …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 1–8 Read article
-
Development of a predictive model for determining mechanical properties of nano Al2O3 reinforced adhesive bonded SS304 single lap joint
Abstract: In this study, single lap joints were prepared by adding nano-additives (Al2O3) in the quantity of 3 wt % in the phenolic resin, and the overlap length was varied to observe the effect on joint engineering properties. In the experiments, a single component system of a specific grade of phenolic resin was used as a binder, and aluminum (AA8011), as well as stainless steel (SS304), was used as adherends. The …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 20–28 Read article
-
An Investigation into the VariablesInfluencing the Densification of Spark Plasma Sintered, 40 Weight Percent Ni-Fe Nano Powder
Abstract: The mechanical alloying process that included high-energy ball milling resulted in particle sizes of 25 mm and 80 mm on average for the Ni-Fe alloy that included 40 percent Ni. At room temperature, highenergy planetary ball milling was carried out over timespan ranging from 15 hours to 60 hours. All of the samples were sintered at the same conditions, which included a temperature of 650 degrees Celsius and a pressure …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 29–35 Read article
-
Effect of Curing Time on Physico-mechanical Properties on Dental Composite
Abstract: This study aim to investigate the influence of curing time on physical and mechanical properties of a dental composite cured by using LED light with intensity of 1500 mW/cm2 in the range of 440-480 nm. We prepared the glass ionomer powder by fusion of various inorganic components at high temperature and studied the influence of silica/alumina ratio keeping other inorganic salts such as Calcium fluoride (CaF2), Sodium Fluoride (NaF), Calcium …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 36–47 Read article
-
Influence of FEF (N550) Carbon Black on Rheological and Physico-mechanical Properties of SBR Vulcanizate for Tyre Application
Abstract: This study aims to investigate the synergistic effect of Fast extrusion furnace black on the rheological, surface morphological and physico-mechanical properties such as tensile strength, hardness and specific gravity of styrene-butadiene synthetic rubber composite. SBR is an elastomer which is an important sort of synthetic rubber. It is a copolymer whose molecular structure primarily consists of organic compound styrene and butadiene chain. Fast extrusion furnace black and high abrasion furnace …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 48–58 Read article
-
Testing for Shielding and Estimation of Linear Absorption Coefficient Using Gamma Irradiation of Polymer Composites
Abstract: The polymer composites were developed for the application of shielding material in a radiation environment. To determine the linear absorption coefficient of the developed materials for neutrons; an experiment was carried out using an Am-Be neutron source of strength ~3 × 107 n/s. The composites of Epoxy polymer were filled with different three fillers; Graphite, Lead, and Boron Nitrided Nanopowder prepared with the same filler content. Transmitted neutrons were detected …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 59–68 Read article
-
Comparative Evaluation of the Effect of Adhesive Restorative Techniques on the Reinforcement of Simulated Immature Permanent Teeth: An in Vitro Study
Abstract: The aim of the study was to compare the reinforcement effect of 3 different adhesive restorative techniques on simulated immature maxillary central incisors after apexification. A total of 30 simulated immature permanent maxillary central incisors were randomly assigned into 3 groups (n=10), according to the reinforcing technique used: Group 1: Nanohybrid composite. (Tetric N-Ceram Ivoclar Vivadent), Group 2: Short-fiber reinforced composite (everX posterior GC EUROPE) extended 3mm below CEJ, covered …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 69–75 Read article
-
Unsaturated Polyester Resin and Rice Husk Composites
Abstract: Plastic is a very useful and important part of human beings but it is quiet harmful to environment. The increasing demand for the eco-friendly material is growing interest towards the field of Composites. The Natural composites of Styrene Diluted Unsaturated Polyester resin are made. Various natural materials are used to make different composites. This study includes Rice Husk Composite of SDUPR. There are many methods to prepare composites. Methods such …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 76–84 Read article
-
Effect of ZrO2 nanoparticles on Electrical conductivity of PVA/PVP polymer blend doped with ammonium iodide
Abstract: This work reports the properties of solid polymer electrolyte films obtained via incorporating varying amounts of ZrO2 nanoparticles into the PVA/PVP polymer blend with ammonium iodide salt. Material synthesis was done by the solution casting technique. Frequency dependent impedance and conductivity parameters of polymer electrolyte films were investigated at different temperatures (303K-353K) using impedance spectroscopy. The results of ionic conductivity of prepared polymer blend samples at various temperatures were studied …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 85–94 Read article
-
Synthesis and Characterization of Al-Mg-Si Alloy based Hybrid Composite Reinforced with SiC and Graphite
Abstract: The present work is carried out to investigate the mechanical properties of Al-Mg-Si alloy matrix based hybrid metal matrix composites (MMCs) using stir casting method owing to its popularity and large scale productions. SiC and graphite reinforcements were added each with 1%, 2%, 3% and 4% respectively to fabricate four composites specimens. X-ray diffractometer and scanning electron microscope were used for phase identification and microstructure characterization (SEM). Density, hardness, compressive …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 9–19 Read article
-
Exploration and Evaluation of Enablers of “Sustainable Freight Transportation” Using Analytic Hierarchy Process (AHP)
Abstract: The main objective of the study is to improve environmental, social, and economic measures. Some other areas of concern of this paper are diminishing the CO2 emissions, effective optimization of the transportation costs and successful utilization of information technology, expanding the freight transportation services, and improving the concept of sustainability in transportation sectors. The focus of this study is on fulfilling sustainable transportation goals, by identifying suitable enablers. Based on …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. S1–S10 Read article
-
Buckling Assessment of Concrete Column, RCC Column and Concrete Column Strengthened by CFRP with Different Slenderness Ratio.
Abstract: Using finite element modeling, this study presents a buckling analysis and total deformation assessment of a concrete column, a column made of reinforced cement concrete (RCC), and a concrete column enhanced with Carbon Fiber-reinforced Polymer (CFRP) laminates (FEM). Utilizing the ansys18.1 software, a comprehensive analysis is carried out for columns that have a variety of slenderness ratios to arrive at a more accurate performance estimation. Because they can support the …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. S11–S22 Read article