tensile strength
60 articles · search the full text for this term
-
Exploring the Mechanical Characterization and Microstructural Properties of the Varying Weight % of Nano Boron Carbide (nB4C) Reinforced Al2024 composites using the Vacuum-Assisted Stir Casting Method
Abstract: In this investigation the stir casting technique is utilized to fabricate Al2024-B4C nano composites. The nanoB4C particles used in the reinforcement material have a particle size of 50 nm and variable weight percentages. In Al2024 composites, boron carbide reinforcement is included at weight percentages ranging from 0% to 3%, with a 1% interval between each percentage addition. Following the casting process, the samples were prepared for microstructural and mechanical evaluation …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 394–404 Read article
-
Chemical Modifications and Tensile Properties of Areca Leaf Sheath Fiber Reinforced Polymer Composites: A Comprehensive Review
Abstract: Areca leaf sheath (ALS) fiber is a promising eco-friendly material, offering a sustainable, lightweight, and cost-effective alternative for low-strength applications. Its natural biodegradability aligns well with the growing global demand for environmentally responsible materials. This review explores the transformative effects of chemical treatments, such as alkali, silane, and benzoylation, on the tensile properties of Areca leaf sheath fibers. Among these, alkali treatment consistently demonstrates the most significant improvement in tensile …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 94–106 Read article
-
Perspectives of 3D-Printed Polylactic Acid-Based Composites Reinforced with Natural Fibers
Abstract: The growing demand for sustainable and biodegradable materials has led to the development of polylactic acid (PLA)-based composites reinforced with natural fibers. This study investigates the mechanical, thermal, printability, and environmental performance of 3D-printed PLA/Natural Fiber composites, addressing key challenges in fiber-matrix compatibility, structural integrity, and biodegradability. Natural fiber reinforcement enhanced Young’s modulus and flexural strength, but excessive fiber content led to agglomeration, reduced tensile strength, and increased brittleness. Thermal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 649–664 Read article
-
Comparative Analysis of 3D Printed Nylon and PETG Specimens for Mechanical Properties.
Abstract: Fused deposition modeling (FDM) is one of the most used additive manufacturing techniques for polymer components. The polymer materials generally used in FDM process are polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), polyethylene terephthalate glycol (PETG), Nylon, etc. The mechanical properties of parts fabricated by FDM depend on material and process parameters. Several researchers have tried to investigate the influence of process parameters on mechanical properties for some of the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 7–14 Read article
-
Enhancing Concrete Durability and Mechanical Properties for Pavement Quality Concrete (PQC) Roads Using Basalt Fiber Reinforcement
Abstract: Concrete, by nature, is brittle and has a very low tensile capacity, which is a double whammy in transportation infrastructure, such as pavement quality concrete (PQC), for roadways, where we need durability and strength. One such method is the use of basalt fibre, as it is a much better way of enhancing the road runway way performance of concrete. This research studies the impact of the addition of basalt fibres …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 266–280 Read article
-
Soil Stabilized Road
Abstract: This research examines the suitability of soil-stabilized roadways for light vehicular movement, offering an economical and practical alternative for areas with limited infrastructure development. Stabilizing soil involves improving its engineering properties by incorporating additives such as cement, lime, or other binding materials. Through stabilization, the treated soil can achieve a compressive strength of approximately 5 N/mm², or 500 tonnes per square meter (t/m²), which is sufficient to support loads imposed …
Published in Journal of Geotechnical Engineering · Vol. 12, Issue 2, 2025 · pp. 38–42 Read article
-
Evaluating The Durability and Environmental Sustainability of Hybrid Natural - Synthetic Fiber Composites
Abstract: This study examines the characteristics of hybrid composites composed of natural fibers (such as jute, hemp, or kenaf) and synthetic fibers (such as glass or carbon) integrated within polymer matrices. The hybridization method seeks to enhance the advantages of both fiber types, hence augmenting overall performance relative to single-reinforced composites. Mechanical properties like tensile strength, flexural strength, impact resistance and hardness were evaluated through experimental tests. The results demonstrate that …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 93–102 Read article
-
Enhancing Mechanical and Thermal Properties of Glass Fiber-Reinforced Epoxy Composites with Silicon Carbide Additives
Abstract: This study explores the production and characterization of glass fiber-reinforced epoxy resin composites enhanced with silicon carbide (SiC) as a reinforcing filler. The primary objective is to evaluate the impact of SiC on the mechanical, thermal, and morphological properties of the composites. Four different samples with varying SiC weight fractions (0%, 5%, 10%, and 15%) were prepared, keeping the glass fiber content constant. The composites were fabricated using a combination …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 69–77 Read article
-
Influence of Alkali Treatment on the Tensile Properties of The Hybrid Fiber Reinforced Polymer Matrix Composite
Abstract: In this study, the effect of alkali treatment on the tensile strength of the hibiscus fiber, gongura fiber, and treated madar fiber-reinforced Polymer Matrix Composite (PMC) is studied. The Sodium Hydroxide (NaOH) solution is utilized for madar fiber treatment. The traditional hand layup methodology was used for fabrication. The influence of tensile property control variables such as duration of fiber treatment, concentration of NaOH for treatment, and proportion of fiber …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 28–34 Read article
-
Performance Evaluation of Modified Concrete Incorporating Fly Ash, Silica Fume, Rice Husk Ash, and Calcium Nitrate
Abstract: The growing demand for sustainable and high-performance concrete has led to the incorporation of supplementary cementitious materials (SCMs) and chemical admixtures to enhance mechanical and durability properties. This study investigates the effect of 15% fly ash, 10% silica fume, 10% rice husk ash, and 3% calcium nitrate as a partial replacement for cement in M25 and M30 grade concrete. Experimental results demonstrate that the modified concrete exhibited an increase in …
Published in Journal of Structural Engineering and Management · Vol. 12, Issue 2, 2025 · pp. 35–39 Read article
-
Hybridization Method for Injection Moulding Process, Optimization with Melting Temperature Parameters
Abstract: Due to the production of plastic products with complex shapes, the plastic injection moulding manufacturing method has recently received a lot of attention. In order to improve manufacturing performance, the cycle time for the injection moulding process has been reduced, the defect known as dimensional warpage that results from temperature differences inside the mould has been reduced, and the mechanical tensile strength of the material has been increased so that …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 337–345 Read article
-
Safety of Structure
Abstract: The thickness of structural components is a vital factor in ensuring their durability and stability under various load conditions. In this study, the material thickness is first determined through the application of bending equations, which are used to analyze regions where bending forces are most significant. The bending stress generated by external loads is considered to calculate the required thickness to prevent failure under such stresses. Additionally, the effect of …
Published in Journal of Industrial Safety Engineering · Vol. 12, Issue 1, 2025 · pp. 1–11 Read article
-
Mechanical Property Assessment of Hybrid Fiber Reinforced Composites Through Experimental Research
Abstract: Natural fibre reinforced composites are gradually taking the place of synthetic fibre composites due to its inexpensive cost, low density, and ease of supply. Furthermore, the addition of some waste materials to composites has remarkable properties that are attracting interest from a wide range of technical domains. Fibre reinforced with glass, carbon, and jute were used to generate hybrid composites. As a filler, different amounts of eggshell powder were mixed …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 244–251 Read article
-
Investigation of Process Specifications on Friction Stir Welded Aluminium 5083 and 6082 Alloys
Abstract: Aluminium 5083 alloys were mainly used for naval based applications because of better corrosion resistance feature. Similarly aluminium 6082 alloy being a structurally significant material found its applications in construction sector. Fusion welding of these two heterogeneous alloys is bit hard, since it evolves many defects. Present Investigation deals with two cases of distinct alloys through FSW process. Case 1 represents 31 experimental trails performed by 5 various tool pin …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 1–11 Read article
-
Improving the Performance of Self-compacting Concrete Using Optimized Admixture Combinations
Abstract: This study explores the influence of various admixture combinations on the performance of Self-Compacting Concrete (SCC), with an emphasis on its flow behavior, compressive strength, tensile strength, flexural strength, and resistance to impact. Various admixtures, including Air-Entraining Agent (AEA), Water-Reducing Plasticizer (WPC), Retarder (RET), and Accelerator (ACC), were incorporated into the SCC reference mix (SP + VMA) to evaluate their impact on SCC performance. A series of tests—such as slump …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 3, 2024 · pp. 81–89 Read article
-
Experimental Investigation and Surface Morphology Study on Areca Fiber Composite Material
Abstract: Composites manufactured from areca fibers had their characteristics assessed in recent research. Shape and size were determined by cutting the stem. It takes six months to dry the fibers once they are taken from the tree stem. Because pectin, cellulose, hemicellulose, and lignin make up the bulk of it. It has great regeneration capacity and is a resource material made of wood fibers. The untreated and chemically treated fibers are …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 459–468 Read article
-
Experimental Evaluation of Strength in Bacterial Concrete Mixtures
Abstract: The incorporation of bacteria into concrete, through the process of Microbiologically Induced Calcite Precipitation (MICP), offers a promising approach to enhancing the mechanical properties and durability of concrete. This research explores the effect of bacterial addition on the compressive strength, split tensile strength, flexural strength, and workability of concrete. Specifically, three bacterial strains—Bacillus megaterium, Bacillus subtilis, and Pseudomonas aeruginosa—were used in varying concentrations (10⁴, 10⁵, and 10⁶ cells/ml) and incorporated …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 3, 2024 · pp. 61–69 Read article
-
Impact of Polypropylene Fibres on the Properties of Concrete
Abstract: This review paper explores the effects of polypropylene fibres on the mechanical and structural properties of concrete. The integration of short, discontinuous fibres into plain concrete enhances its post-cracking behavior and overall performance, with notable improvements in tensile strength, fracture strength, toughness, impact resistance, and flexural strength. These fibres effectively control crack propagation, increase energy absorption, and improve durability under varying loading conditions. A comprehensive analysis of prior research highlights …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 3, 2024 · pp. 55–60 Read article
-
Investigation on Tensile Properties of Redwood PLA Using FDM Process
Abstract: Fused Deposition Modeling (FDM) is an additive manufacturing technique employed to construct comprehensive 3-dimensional models using a variety of materials, catering to diverse applications. This study explores the fabrication of REDWOOD polylactic acid using (FDM) additive manufacturing processes. REDWOOD PLA, recognized for its biodegradability and renewable sourcing, holds promise as an eco-friendly material for 3D printing applications. The research investigates the tensile properties of REDWOOD polylactic acid (PLA) fabricated through …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 668–673 Read article
-
New Generation Waste Material as Sustainable Ingredient in Concrete: An Experimental Approach
Abstract: E-waste, including devices like phones and computers, poses serious environmental risks. To mitigate these, the construction industry is exploring e-waste as a material to enhance concrete strength and durability. Hence, the present study assesses the performance of M40-grade high-strength concrete by replacing coarse aggregates with 0% to 30% e-waste plastics at various intervals. As the e-waste replacement increased, fresh concrete's workability decreased gradually. The mix containing 30% e-waste experienced the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 141–156 Read article