Solidification
6 articles · search the full text for this term
-
Numerical simulation and Artificial neural network illustration of phase-change material integrated into lattice structures printed in 3D
Abstract: This work examines the phase change material (P.C.M.) deposited in various lattice formations—such as “S.C., B.C.C., and F.C.C”.—at varied characteristics. The test concentrates on comprehending heat transport properties and thermal activity throughout the “melting and solidification processes”. The heater's maximum temperature, P.C.M. “melting and solidification”, and Nusselt number are among the essential factors examined. According to the findings, the heater's maximum temperature drops as porosity increases. Although the Nusselt values …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 175–183 Read article
-
STABILIZATION OF HEAVY METAL SLUDGE TO PASS THE TCLP TEST USING CEMENT WITH A SINTER AS A ADDITIVE
Abstract: According to the U.S. Stabilisation is the best-proven technology now in use, according to the Environmental Protection Agency's definition in Title 40, Part 268 of the Code of Federal Regulations (40 CFR 268).This method prevents harmful contaminants from leaking into the environment by physically and chemically trapping them all in a matrix. The investigations used 15 different water-mixed combinations of cement, fly ash, sinter, and lime. The study also examined …
Published in Journal of Polymer & Composites · Vol. 11, Issue 10, 2023 · pp. 16–24 Read article
-
Solidification of Brass Casting in Green Sand Mould: A Numerical and Experimental Study
Abstract: Casting which is also known as founding, is one of the earliest metal shaping methods. It means the pouring of molten metal into the refractory mould then allowing it to solidify. After solidification removing of part from the mould either by breaking the mould or ejecting the mould part. Present study has been focused on solidification of brass in green sand mould formulation. Two-dimensional heat conduction equation in cartesian co-ordinate …
Published in Journal of Mechatronics and Automation · Vol. 2, Issue 3, 2015 · pp. 24–30 Read article
-
Effects of Composition on Structure & Mechanical Property of TiAl Based Intermetallic Compounds
Abstract: The effects of Al content and ternary additions such as Mo, V and Si in as cast g based alloys made by plasma arc melting on solidification structures and mechanical properties were studied. The Columnar g /a2 lamellar structures in Al-lean alloys due to primary a solidification had higher room temperature fracture strength and strain than g phase structures through the reaction of L + a = g in Al-rich …
Published in Journal of Materials & Metallurgical Engineering · Vol. 11, Issue 3, 2021 · pp. 1–10 Read article
-
Effect of Mould Cavity Thickness on Cooling Rate of Aluminium with Temperature Dependent Properties
Abstract: Solidification study of aluminium with temperature dependent thermal properties has been conducted. Effect of the mould cavity wall thickness on the cooling rate has been the target in the present work. Casting is earliest metal shaping process and has been used in many industries and households. Solidification during casting is the most crucial event which has been studied by the many researchers because it affects the quality of the casting …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 3, Issue 1, 2016 · pp. 31–35 Read article
-
Microstructure and Mechanical Properties of Thin Wall Ductile Iron
Abstract: Currently many cast parts are produced in aluminum rather than cast iron, because of the drive to get high strength /weight ratio for application in automobile and aerospace. Ductile Iron casting of approximately 2-3mm section thickness better known as Thin wall ductile iron (TWDI) having high strength /weight ratio and better mechanical properties than Aluminum alloys. The effect of various parameters like, post inoculation, gating and feeding, moulding sand mix …
Published in Journal of Automobile Engineering and Applications · Vol. 4, Issue 2, 2017 · pp. 35–39 Read article