SEM
36 articles · search the full text for this term
-
In-Situ Polymerized GO/PANI Composites: Structural Evolution, Optical Modulation, and NH₃ Sensing at Room Temperature
Abstract: Graphene oxide (GO)/polyaniline (PANI) composites with varying PANI contents (20, 40, and 60 wt%) were synthesized via in-situ oxidative polymerization and systematically investigated for their structural, morphological, optical, and gas-sensing properties. X-ray diffraction (XRD) confirmed a progressive increase in interlayer spacing and partial exfoliation of GO layers with increasing PANI content, indicating intercalation-assisted hybridization. Fourier transform infrared (FTIR) spectroscopy revealed the characteristic vibrational bands of both constituents and confirmed strong …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Mechanical Behavioral Analysis of Sugarcane Bagasse, Coconut Fiber and Kevlar Fiber Reinforced Composite with Micrographs
Abstract: Asbestos and alloys are materials that are frequently used as brake pads; however, because these materials pose risks to human health and the environment, including lung cancer, it is necessary to replace the materials used in brake pads. In place of the current brake pads, composite fibers such as kevlar, sugarcane bagasse, and coconut are studied in this study. The procedure of manually laying up composite molding is used to …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 282–296 Read article
-
Catalyst-Driven Degradation and Failure Analysis of Intergranular Cracking in 316H Studded Pipes under Refinery Heat Recovery Conditions
Abstract: A failure analysis investigation was carried out on a high-temperature studded pipe used in a convection module for heat recovery in an oil and gas refinery application after leakage was detected during pre-commissioning hydrotesting. The investigated pipe was manufactured from AISI 316H austenitic stainless steel, and carbon steel studs had been joined to its outer surface by high-frequency resistance welding. Two leaks were reported in the pipe under investigation, and …
Published in Journal of Catalyst & Catalysis · Vol. 13, Issue 1, 2026 Read article
-
Thermal and Morphological Characterization of Rice Starch–Charcoal Composites for Eco-Friendly Engineering Applications
Abstract: This work focuses on the development and evaluation of rice starch–charcoal–based composite materials to overcome the limitations of natural composites with low thermal properties. In order to examine the impact of filler concentration on thermal and structural performance, eight composite specimens were created by altering the ratios of rice starch and charcoal. TGA, DTA, AFM, SEM, and measurements of thermal conductivity and effusivity were used to thoroughly characterize the composites. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1286–1297 Read article
-
Gamma Irradiation Effects on Structural and Optical Properties of PVA/Al₂O₃/TiC Polymer Nanocomposites for Optoelectronic Applications
Abstract: PVA/TiC/Al2O3 nanocomposite (PTA) films were successfully prepared via the solution casting method. The impact of high-dose gamma (γ) irradiation (30 kGy) on the structural and optical properties of PVA/TiC/Al2O3 nanocomposites was systematically explored using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and UV–Visible spectroscopy. XRD analysis confirmed the semi-crystalline nature of the nanocomposites, which was found to decrease upon incorporation of Al₂O₃ nanoparticles and exposure to …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 717–729 Read article
-
Experimental Investigation of Boron Carbide Reinforced Al-Mg-Si Alloy Nano Composites by the Stir Casting Method Using Machine Learning Algorithm
Abstract: For the purpose of this experiment, Al-Mg-Si alloys were manufactured with the use of the stir casting process with a metal mold. The alloys had different weight percentages of nano boron carbide, which ranged from 0 to 4% by weight. The intervals between the percentages were 0.5. Following that, the microstructural and mechanical parameters of the as-cast alloy and the nano composites were compared and contrasted according to ASTM Standards …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1766–1779 Read article
-
Role of Strontium in Structural and Dielectric characterstics of Barium Titanate
Abstract: Ba₀.₇₅Sr₀.₂₅TiO₃ (BST) compound was synthesized through the conventional solid-state reaction methodology, aimed at investigating its structural, microstructural, and dielectric characteristics. The structural characterization was executed employing X-ray diffraction (XRD), and the resultant diffraction patterns were refined utilizing the Rietveld method, which substantiated the establishment of a single-phase perovskite configuration exhibiting tetragonal symmetry and belonging to the P4mm space group. The refined lattice parameters revealed subtle distortions correlating with the substitution …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1157–1163 Read article
-
Development and Analysis of Novel Silver Ion-Conducting Glass-Polymer Electrolytes
Abstract: The development of efficient and stable solid electrolytes is crucial for advancing energy storage technologies such as solid-state batteries and electrochemical devices. In this study, a novel series of silver ion-conducting glass–polymer electrolytes (GPEs) based on the composition (1–x) PEO: x[0.75AgI:0.25(Ag₂O:WO₃)] with x ranging up to 50 wt.% was synthesized and thoroughly analyzed. Unlike conventional techniques such as solution casting or sol–gel methods, these GPEs were fabricated using an innovative …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 600–605 Read article
-
Synthesis and Ion Transport Studies of a New Potassium Ion-Conducting Nanocomposite Polymer Electrolyte
Abstract: The pursuit of safe, efficient, and sustainable energy storage solutions has intensified research on nanocomposite polymer electrolytes, especially for next-generation battery technologies. This work reports the synthesis and ion transport characteristics of potassium ion-conducting nanocomposite polymer electrolytes (NCPEs), emphasizing their structural, electrical, and electrochemical performance. To enhance ionic conductivity and mechanical strength, polymer matrices were reinforced with nanoscale ceramic fillers. A new potassium ion-conducting NCPEs: (1-x)[70PEO:30KCl] + x SiO₂ (where …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1496–1504 Read article
-
Optimization of Direct Ink Writing Process Parameters for Liquid Silicone Rubber/TiO2 Composite Ink
Abstract: The purpose of this research is to develop and optimize the Liquid Silicone Rubber (LSR)/Titanium Dioxide (TiO₂) composite inks in Direct Ink Writing (DIW)-based 3D printing systems. The primary research objective was to use enhancement of mechanical, rheological, and dielectric characteristics of LSR using TiO₂ reinforcement but still retain extrusion stability and dimensional consistency. TiO₂ content (0, 5, 10, and 15 wt%) and catalyst and glycerol ratios were regulated and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 240–259 Read article
-
Application of Thermal Spray Coatings for Corrosion Control in Oil and Gas Refineries
Abstract: In today’s context, Thermal Spray Coating (TSC) has emerged as a highly durable and reliable alternative to traditional Hot-Dip Galvanizing (HDG). It is increasingly being adopted for both new and existing industrial structures due to its long-lasting protection—often exceeding 25 years—while requiring little to no maintenance. Unlike HDG, which cannot be welded on-site and often poses challenges with repair methods such as liquid coating or cold spray, TSC offers greater …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 106–115 Read article
-
Kinetics of Crystallization and Microstructural Evolution of Commercial Fluorophlogopite Machinable Glass- Ceramics in the System SrO∙4MgO∙Al2O3∙ 6SiO2∙2MgF2 with Varying in B2O3
Abstract: Glass materials based on fluorophlogopite stoichiometry with varying concentrations of B₂O₃ were synthesized using the melt-casting method, followed by heat treatment at different crystallization temperatures. The resulting glass and glass–ceramic samples were characterized using differential thermal analysis (DTA), scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FT-IR) spectroscopy. Kinetic analysis revealed that the activation energies required for the formation of glass–ceramics were 192.77 kJ mol⁻¹ and 210.47 kJ …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 12, Issue 3, 2025 · pp. 1–16 Read article
-
Comprehensive Review of Nanomaterials Synthesis Methods, Characterization and Multifaceted Applications in Medical Field
Abstract: Nanomaterials associated by special qualities derived from their nanoscale size nanomaterials have tremendous potential in a variety of industries like, medicine & healthcare. Due to today busy life & unhealthy life schedule many abnormal cell growth take place in our body & affect the other organ. Sometimes it may leads to cancer & others dangerous diseases, nanomaterials such as nanotubes, liposomes & polymeric micelles are help for designing the drugs …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 657–669 Read article
-
Synthesis and characterization of mixed SnO2-ZnO Nano composites material to study the kinetics of catalytic reduction of Aromatic Nitro compounds
Abstract: A straightforward and cost-effective method was employed to synthesize zinc oxide (ZnO) nanostructures supported on tin oxide (SnO₂) for catalytic applications. This hybrid nanocomposite, formed by integrating ZnO with SnO₂, exhibited impressive catalytic activity in the reduction of various nitro compounds. The synergistic interaction between ZnO and SnO₂ significantly enhanced the surface area and active sites of the catalyst, thereby improving its overall efficiency. The resulting SnO₂-ZnO nanocomposite not only …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 15, Issue 3, 2025 · pp. 8–14 Read article
-
Preparation and characterization of High-performance ZnO/PVB Nanocomposite films for UV-shielding and Optoelectronics
Abstract: Zinc oxide nanoparticles can be incorporated into polymer matrices to create materials for various high-performance engineering applications. In this study, zinc oxide nanoparticles were reinforced at different loadings (0.5, 1.0, 0.5, 1.0, 1.5, and 2.0 wt.%) in polyvinyl butyral matrix to synthesize nanocomposite films using the solution casting method. The impact of zinc oxide nanofiller on the morphology and ultraviolet-shielding performance of polyvinyl butyral nanocomposite films was evaluated using various …
Published in Nano Trends – A Journal of Nano Technology & Its Applications · Vol. 27, Issue 3, 2025 · pp. 35–53 Read article
-
Effect of Steam Flash Explosion Conditions on Preparation of Reed Pulp
Abstract: The effects of different steam explosion conditions on preparation of reed pulp by steam flash explosion were analyzed. Because the main factors affecting steam explosion are steam pressure, retention time and liquid-to-reed ratio, so that the effects of these conditions on the steam explosion pretreated reed straw, and constituent of reed pulp were analyzed. Reed straw samples, 2~3cm in length, were loaded into a 5L stainless steel reactor and treated …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 16, Issue 2, 2025 · pp. 115–128 Read article
-
Gas Sensors Fabricated using Carbon Powder Derived from Dried Banana Peels Waste to detect Methanol, Ethanol, Acetone Vapors and Carbon Dioxide Gas
Abstract: Low cost and environmentally friendly activated carbon powder was synthesized using waste banana peels. Phosphoric acid was utilized as activation agent. Doctor blade method was employed to fabricate films of activated carbon on conductive or nonconductive glass substrates. Films were subsequently annealed at 70 0C for 30 minutes in air. According to XRD patterns, single phase of activated carbon was crystallized in thin film form. Carbon prepared from banana peels …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 14–25 Read article
-
Mechanical Property Assessment of Hybrid Composite Laminates Composed of Jute Glass Fibers in Combination with Flax, Hemp, Sisal and Kenaf Fibers Using the Hand Layup Technique
Abstract: The present work compares the properties of various hybrid composite laminates manufactured using the hand layup technique and addresses their production process, based on glass fiber as the exterior layer and natural fibers (flax, hemp, kenaf, jute, and sisal) as interior layers, in an epoxy resin. Five stacking sequences A-GJJJJG, B-GFJJFG, C-GHJJHG, D-GKJJKG, and E-GJSSJG were used to prepare the test specimens. According to ASTM guidelines, experiments were performed to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 103–113 Read article
-
Experimental Investigation Mechanical Behaviour of Composite Made by Carbon Fibre Mixed with Zro2 and Phenolic Resin
Abstract: Composites are one of the major research criteria in aerospace technologies to fulfil the present needs. Addition of materials to carbon fibers without increasing of weight of the parts Nano and micro fillers have its own criteria in improving mechanical properties. ZrO2 particles added to carbon fibers can improve the strength with a light add up in density. Present study focused on the mechanical behavior of zirconium oxide addition to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 562–573 Read article
-
Dielectric Studies of 0.5Ba0.8Ca0.2TiO3.0.5CaCu3Ti4O12 Nanoceramic Fabricated by Chemo-mechanical Process
Abstract: The present investigation is aimed toward investigate a straightforward, inexpensive, and environmentally friendly chemo-mechanical method for preparing high-dielectric materials, specifically 0.5Ba0.8Ca0.2TiO3.0.5CaCu3Ti4O12 (BCT-CCTO), by combining metal nitrate combustion with solid TiO2 powder and titanium isopropoxide, Ti (OR)4. The composite was prepared by the mixing of individual materials of Ba0.8Ca0.2TiO3 and CaCu3Ti4O12 through the chemo-mechanical method. Initially, 99% pure Ba (NO3)3, Cu (NO3)2∙3H2O, TiO2 and glycine were taken in their stoichiometry ratios. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 12–21 Read article