epoxy
26 articles · search the full text for this term
-
Experimental Study on Load Transfer Mechanism in Columns Retrofitted by Bonding Precast Segments and FRP Wrapping
Abstract: An experimental study was conducted to investigate the load transfer mechanism in columns retrofitted with precast segments and Fiber-Reinforced Polymer (FRP) wrapping. As the demand for structural retrofitting grows, it becomes crucial to comprehend the behavior and effectiveness of retrofit techniques to ensure the safety and integrity of existing infrastructure. The study involved subjecting a series of column specimens to axial compression loads in order to evaluate the load transfer …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 153–165 Read article
-
Dielectric Properties of Reduced Graphene Oxide with Nickel Cobalt Ferrite and Nickel Zinc Ferrite Epoxy Nanocomposites
Abstract: In this work, two systems of the composite were prepared using NiCoFe and NiZnFe with reduced graphene oxide(rGO) epoxy and the samples were subjected to electrochemical impedance spectroscopy (EIS). The Quality factor and loss tangent values of the composite was found out as a function of frequency. The modified ferrite-graphene-epoxy blends show dielectric loss and Quality factor values at low frequency. The incorporation of graphene aims to improve electrical conductivity, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 11, 2023 · pp. 28–37 Read article
-
Evaluation of the Properties of Sugarcane Bagasse Composites
Abstract: Many of the researches are ongoing towards these natural fibre composites in order to replace few materials like plastic and ceramics. In this work we have focused on the preparation of a polymer matrix composite using sugarcane bagasse fibre which intern helpful to study regarding its mechanical behavior. Over the past thirty years of composite materials history says that it has been the dominant emerging materials which have proved with …
Published in Journal of Production Research & Management · Vol. 10, Issue 2, 2020 · pp. 20–23 Read article
-
Optimization of Dry sliding Wear Performance of pongamia oil cake filled Basalt Epoxy Composites by Taguchi Approach
Abstract: The study finds a possible utilization of natural pongamia oil cake for developing a new vista in the incorporation of the oily nature of natural waste material into polymer matrix composites. The woven basalt fibres were reinforced within an epoxy matrix incorporated with distinct weight percentages of pongamia oil cake (up to 6wt. %) and composite samples were composed by using resin transfer moulding process. The experimentation has been carried …
Published in Journal of Polymer & Composites · Vol. 7, Issue 2, 2019 · pp. 8–16 Read article
-
Effect of Mixing Time on Mechanical Properties of Epoxy-Fly Ash Composite
Abstract: Particulate reinforced polymer composites have been designed to improve the (polymer) composite properties and with reduction of cost. In the present study, fly-ash is used as a filler material. Samples are made with different mixing times i.e. 5, 10, 15, 20, 25 and 30 min. Ultrasonic and magnetic mixing are the two ways to mix the particulate as fillers. The resulting mechanical properties such as flexural strength, tensile strength and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 2, 2015 · pp. 11–17 Read article
-
Tribological Behaviour of Epoxy-Marble Powder Composite with Taguchi Optimization Technique
Abstract: Epoxy resin strengthened with marble powder particles is prepared by ultrasonic mixing strategy. Pin-on-Disc wear trial of the developed composite is done concurring with Taguchi optimisation. An orthogonal array is displayed and analysed the affecting parameters like fraction of marble powder reinforcement, load, sliding speed and track diameter on the composite. Signal to noise ratio analysis optimises the parametric conditions that yield minimum wear rate, minimum frictional force and minimum …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 2, 2018 · pp. 110–117 Read article