Search
17 articles for “preheating”
-
Revamp of Feed Preheat Network Using Aspen Hysys in a Kero Hydro-Desulphurization Unit
Abstract: The paper is based on the revamp of feed preheat network in a Kero hydro-desulphurization unit. This revamp is beneficial as it does not require additional equipment to raise the feed temperature. Desulphurization of crude is a catalytic process used in oil and gas refining industry to remove sulphur content from refined petroleum products. Previously, feed was charged from the crude distillation unit at 103°C. Due to envisaged changes, the …
Published in Journal of Petroleum Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 29–38 Read article
-
Evaluation of the effect of fuel preheat on the performance and emission of a diesel engine using regression analysis.
Abstract: In this work an attempt was made to determine the effects of loading in Kirloskar 3.7 kW single cylinder, four stroke, compression ignition engine with “diesel and biofuel”as fuels. The effects of ‘fuel preheat’ on brake power and emission characteristics were investigated. The fuel preheat temperature was increased from 35C to 50C and emissions like CO and HC were found to be decreasing considerably, but, slight increase in brake power …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 2, 2018 · pp. 36–41 Read article
-
Optimization of Stellite Defect in Manufacturing of Engine Valves: A Review
Abstract: Intake and exhaust valves are the important components of an engine valves which are used to control flow and replacement of fuel gases inside the cylinder. This work mainly deals with defect known as stellite defect in different sizes of engine valves; and methodology adopted to prevent valve from stellite defect. Valve base material is low alloy steel (AISI 4140) and upper surface of engine valve is generally hard faced …
Published in Journal of Automobile Engineering and Applications · Vol. 3, Issue 1, 2016 · pp. 1–4 Read article
-
Application of flux cored arc welding (fcaw) without pre-heating for heavy structures in ship building fabrication & construction of heavy offshore structural steels
Abstract: In fusion welding processes, the reason often given to explain the need for preheating, controlling the inter pass temperature (in multi-pass welds), and post-weld heat treatment (PWHT) is to reduce the risk of residual stresses and it can be removed by heating weldment in the heat affected zone (HAZ). Cold cracking is a hydrogen embrittlement phenomenon, often referred to as hydrogen induced cracking or HAZ cracking. During the construction and …
Published in Journal of Construction Engineering, Technology & Management · Vol. 10, Issue 1, 2020 · pp. 20–28 Read article
-
Experimental Investigation of Dilution Control Using Advanced Gas Metal Arc Welding Process
Abstract: This work investigates the amount of reduction in dilution by using Advanced Gas Metal Arc Welding (AGMAW) process. Dilution is the ratio of area of the base metal melted to the total area of weld bead measured across a given weld bead cross section. Dilution is one of the most important factors governing the success of any surfacing operation and is expressed in percentage. The AGMAW is a self-coined word …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 1, Issue 3, 2014 · pp. 1–7 Read article
-
Optimization Of Mechanical Properties Of 500/7 Grade Ductile Cast Iron (DCI) By Using SMAW: Applications In Reinforced Composites And Thermoplastics Through Taguchi & GRA
Abstract: Welding, a critical manufacturing process, is broadly engaged to join metals and thermoplastics using heat, pressure, or both. This study inspects the Shielded Metal Arc Welding (SMAW) method to optimize welding parameters and improve the mechanical properties of Ductile Cast Iron (DCI) grade 500/7, a material widely used in high-strength and thermal conductivity applications in aerospace and automotive sectors. Using an L9 OA (orthogonal array), experiments were conducted on nine …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 204–222 Read article
-
Dissimilar Joining Of Aluminium Alloy to Copper Using Tungsten Inert Gas Welding Process
Abstract: Aluminium-copper dissimilar joints are applicable to electrical industry. 2 mm thick aluminium alloys (A1100) sheet is joined to 1 mm thick copper (Cu-DHP) sheet using tungsten inert gas welding (TIG) process. The effect of process parameters like heat input, torch orientation, arc weaving on mechanical properties of the joint are studied. In this combination the molten pool generated by melting of aluminium edge will wet the coppersurface to form a …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 2, 2018 · pp. 15–20 Read article
-
Efficiency Improvements in Domestic LPG Burner
Abstract: AbstractExperiments are conducted on the domestic LPG burner with porous material as preheating and combustion medium. The burner consist of two layers of porous medium. The combustion zone is made up of silicon carbide and metal chips. The stainless-steel balls as preheating zone. The performance of the domestic LPG conventional burner is calculated in terms of heating efficiency for the different thermal inputs(Wattages) and results are compared with that of …
Published in Recent Trends in Fluid Mechanics · Vol. 6, Issue 3, 2019 · pp. 7–11 Read article
-
Effect of Graphite and Titanium Dioxide on Mechanical Properties and Wear Behavior of Al based HMMCs
Abstract: Aluminium Metal Matrix Composites (MMC) is beneficial in a diversity of applications of engineering, particularly due to their strength while being lightweight. The intention of this paper is to develop a Hybrid Metal Matrix Composite (HMMC) using base metal aluminium alloy which is reinforced with different wt% of Graphite and Titanium Dioxide and then study the different mechanical properties like microstructure analysis, tensile strength, hardness, and wear behavior of HMMC …
Published in Journal of Polymer & Composites · Vol. 11, Issue 13, 2023 · pp. 20–30 Read article
-
Enhancing Engine Efficiency and Reducing Emissions: A Comprehensive Review of Air Calorimeter Technology
Abstract: The article talks about the idea behind this project to pre-heat the intake air that passes through the carburettor to increase a petrol engine's fuel efficiency. The vaporization of petrol in the carburettor is influenced by the humidity of the surrounding air. Therefore, vaporization can be facilitated, and full combustion can be accomplished by preheating the carburettor's incoming air for a significant amount of time. Additionally, by lowering the amount …
Published in Journal of Aerospace Engineering & Technology · Vol. 15, Issue 1, 2025 · pp. 8–13 Read article
-
Mechanical & Tribological Characterization of Al2024-Alumina-Graphite Reinforced Monolithic and Hybrid Composites
Abstract: This work investigates the mechanical characteristics of Al2024-Al2O3-Graphite reinforced monolithic and hybrid composites fabricated by the stir casting method. Exploratory work involved the fabrication of monolithic composites with varying Al2O3 contents (5-8 wt%) and hybrid composites with the ratios of Al2O3 (2-6 wt%) and Graphite (1-3 wt%) in matrix Al2024. For improving their dispersion, preheated reinforcement particles were introduced in matrix alloy at controlled stirring rates. A homogeneous particle distribution …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 823–836 Read article
-
Comparative Investigation on Mechanical Properties of AMCs Fabricated through Liquid and Solid-State Fabrication Process
Abstract: This current research work is primarily focused on comparative experimental study on effect of two distinct fabrication process routes i.e. liquid state and solid state process and their corresponding parameters on microstructure and micro-hardness properties of Aluminium matrix composites (AMCs). In this work, AMCs were fabricated by reinforcing Al2O3 powder materials of 5, 10 and 15 wt.% into pure Aluminum (Al) matrix phase through two distinct processes; liquid state (stir …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 202–215 Read article
-
Improved Gasoline Yield from Fluid Catalytic Cracker Riser Reactor
Abstract: The study focused on improvement and conversion of vacuum gas oil as feedstock to fluid catalytic cracker riser reactor with enhanced yield of gasoline, liquefied petroleum gas and fuel gas products and low yield of coke as undesired product. Thus, steady state performance models were developed for riser reactor as a plug flow reactor using five lump kinetic scheme to study the cracking operations. Models were developed for the riser …
Published in Journal of Catalyst & Catalysis · Vol. 9, Issue 3, 2022 · pp. 1–14 Read article
-
Experimental Investigation on the Effect of Jatropha Curcas Oil and Diesel Fuel Blend as a Fuel on Engine Components and Lubricating Oil
Abstract: Depletion of fossil fuel source and fluctuating fuel price led researchers to focus on developing new agro-based alternative fuels, which will provide sustainable solution to the energy crisis. The trend of using vegetable oil as an alternative fuel for diesel engine dated late 20th century but until now research is continued due to its benefis. Straight vegetable oils could be used directly but they need modification in order to minimize …
Published in Journal of Industrial Safety Engineering · Vol. 7, Issue 3, 2020 · pp. 36–45 Read article
-
Study the Effect of Variation of Crude Assay on the Design of Distillation Column
Abstract: The purpose of this study is to investigate the effect of variation of crude assay on the design of crude distillation column. Different crudes assay (six samples of Sudanese crude oil) with different properties which are processed at the Khartoum Refinery Company have been simulated using Aspen HYSYS under the same operating conditions in order to identify the effect of this variation. Energy consumption optimization is done by using preheated …
Published in Journal of Petroleum Engineering & Technology · Vol. 6, Issue 3, 2016 · pp. 61–76 Read article
-
A Review on Earth-Air Heat Exchanger Systems
Abstract: AbstractEarth-air heat exchanger (EAHE) is a system which uses the heat and cool of ground and is utilized for the space heating and cooling purposes. Performance of EAHE is dependent on the thermal properties of soil. If the thermal quality of soil is poor so the pipe is to be buried at more depth. The concept exploits the subsoil thermal energy and uses it for producing indoor thermal comforts in …
Published in Recent Trends in Fluid Mechanics · Vol. 7, Issue 1, 2020 · pp. 9–14 Read article
-
Waste Heat Recovery Energy Analysis in Cement Plant by Using AQC
Abstract: AbstractA waste heat recovery system produces power by utilizing the heat energy lost to the surroundings from thermal processes, at no additional fuel input. This research article presents a waste heat in cement plant industry for improving energy efficiency of boiler by using AQC. In the dry process cement plants, nearly 40% of the total heat input is rejected as waste heat from exit gases of preheater and grate cooler. …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 8, Issue 2, 2018 · pp. 1–6 Read article