Search
9 articles for “Voltage Sag”
-
Power Quality Improvement in Grid-Connected PV Systems using TCSC
Abstract: Power quality issues such as voltage sags, swells, and harmonic distortions pose significant challenges to the stability and efficiency of grid-connected systems. This study presents a simulation and analysis of a Thyristor-Controlled Series Capacitor (TCSC) for mitigating voltage sags and swells, thereby enhancing overall power quality. A grid-connected photovoltaic (PV) system integrated with a TCSC is modelled and simulated using MATLAB/Simulink to evaluate its performance under diverse operating conditions. The …
Published in Trends in Electrical Engineering · Vol. 14, Issue 3, 2024 Read article
-
Literature Review and Research Gaps in Power Quality Enhancement: From Conventional Methods to Intelligent Solutions
Abstract: Power quality (PQ) has become a critical concern in modern electrical power systems due to the rapid integration of renewable energy sources, proliferation of power electronic devices, and increasing sensitivity of loads. This paper presents a comprehensive literature review and research gap analysis of power quality enhancement techniques, ranging from conventional approaches to emerging intelligent solutions. Traditional methods, including passive filters, capacitor banks, and synchronous condensers, have been widely employed …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 4, Issue 1, 2026 · pp. 38–80 Read article
-
Enhancement of LVRT Capability in DFIG based Microgrids Using STATCOM
Abstract: The improvement of a grid-connected wind microgrid's Low Voltage Ride-Through (LVRT) capability using a Static Synchronous Compensator (STATCOM) is investigated in this research. The increasing penetration of wind energy into modern power systems necessitates advanced control strategies to maintain grid stability during voltage disturbances and fault conditions. In this study, a STATCOM is employed with an effectively tuned PI controller to provide enhanced dynamic response, voltage regulation, and reactive power …
Published in Trends in Electrical Engineering · Vol. 16, Issue 2, 2025 Read article
-
Modelling and Control of Grid-Connected PV–Battery Hybrid System Using Dynamic Voltage Restorer for Enhanced Power Quality
Abstract: The integration of large-scale photovoltaic (PV) systems into modern power grids introduces significant challenges in maintaining power quality, including voltage sags, swells, and harmonics. To address these issues, this study presents a comprehensive modelling and control framework for a grid-connected PV–Battery hybrid system equipped with a Dynamic Voltage Restorer (DVR). The PV array is modelled using detailed mathematical equations, while the DC–DC converter incorporates advanced Maximum Power Point Tracking (MPPT) …
Published in International Journal of Electrical Power and Machine Systems · Vol. 3, Issue 2, 2025 · pp. 43–58 Read article
-
Analysis of Power Quality Disturbances in Distribution Systems with Renewable Energy Integration
Abstract: The growing integration of renewable energy sources within the electrical distribution systems has greatly altered the working dynamics of the contemporary power grids. The introduction of intermittent and nonlinear sources (solar photovoltaic and wind energy systems) leads to a wide range of power quality disturbances, however. The current paper includes the in-depth examination of the problem of power quality in the distribution systems with the integration of renewable energy. The …
Published in Trends in Electrical Engineering · Vol. 16, Issue 1, 2025 Read article
-
Efficient Fault Detection in Power Transmission: A Review of Three-Phase Line Fault Detection with Hybrid Energy using MATLAB
Abstract: In urban regions, the density of power demand has significantly increased recently. Large-scale subterranean power cable installations are beginning to take the place of overhead transmission lines everywhere in the world because of environmental concerns in highly populated areas. The present project's primary objective is to use MATLAB to create a simulation model that includes 3ph symmetrical and unsymmetrical defects. Some have proven to be effective in detecting errors while …
Published in International Journal of Electrical Power and Machine Systems · Vol. 1, Issue 1, 2023 · pp. 42–47 Read article
-
Improved Unified Power Quality Conditioner Design and Numerical Simulation for Power Quality Improvement
Abstract: Harmonic currents can distort the waveform voltage, resulting in a weak signal. There is also an increase in the number of loads requiring enough sinus tension to function properly. As electronic devices become more power-sensitive, people are becoming increasingly interested in power conditioning solutions. Therefore, if the amount of electricity being generated falls below a certain threshold, some type of compensation must be provided. Unified Power Quality Controller (UPQC) is …
Published in Journal of Microwave Engineering and Technologies Read article
-
Time and Frequency Response of Non-uniform Overhead Lines Under Corona
Abstract: This study presents an efficient and direct technique for determining both the time and frequency responses of non-uniform overhead power transmission lines operating under corona conditions. The assumed-line's non-uniformity is due to the conductors’ sag. Expressions will be presented for the location-dependent line surge impedance and the unevenly distributed lines’ electrical parameters. The analysis starts with solving the relevant system of differential and algebraic equations, subject to the boundary conditions. …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 2, Issue 2, 2024 · pp. 25–33 Read article
-
An Experimental Investigation of Machining Parameters on Aluminum Composites
Abstract: The need for a material with good mechanical, thermal, and wear resistant properties is satisfied by aluminum composite. However, the biggest obstacle to substituting it with alternative materials is the machining challenges. For this kind of hard-to-cut material, electric discharge machining is a very efficient method. Thus, using a Taguchi-based method, an attempt has been made to determine the most advantageous amount of input parameters for EDM of Al composite. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 8–13 Read article