Search
6 articles for “Drilling fluid”
-
A Ponder & Sedulousness Of Legion Shale Stabilizing Materials In Aqueous Based Drilling Fluid During The Process Of Borehole Strengthening
Abstract: Drilling fluid used while drilling the layers of shale will have the potential of reacting with water which tends to increase stickiness, induce swelling and promote sloughing of the borehole. This results in the reduction of drilling fluid circulation, increased mud loss, increase in torque and drag, reduction in lubricity. This will ultimately result in the increase of Non-Productive Time (NPT) during drilling which in turn increases Capital Expenditure (CAPEX) …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 35–40 Read article
-
Drilling Fluid Characterization (Filtration Test)
Abstract: This report explores the formulation and testing of a water-based drilling mud used in drilling operations, where fluid circulates through the drillstring and returns to the surface. The study mixes 315 ml of water with 35 ml of corn oil to create the drilling mud and investigates the role of barite in increasing mud density to maintain a hydrostatic pressure capable of managing formation pressure. The findings reveal that increasing …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 17–26 Read article
-
Evaluation of Physico-Chemical Parameters of Drilling Fluid and Its Effects on Water Quality Discharged in (Okoroagu River) in Etche LGA of Rivers State
Abstract: The study evaluated the surface water quality of Okoroagu River, Niger Delta of Nigeria, in order to determine the water quality index. Water samples were collected at five sampling points of the Okoroagu river. The results revealed that the Physicochemical and heavy metals parameters exceeded the NSDWQ and WHO recommended permissible limits except for TDS, pH, EC, Zinc, Chromium, Nickel and Manganese whicht were within the acceptable limit. The water …
Published in Journal of Water Pollution & Purification Research · Vol. 12, Issue 1, 2025 · pp. 32–44 Read article
-
Use of Coconut Fibre as a Suitable pH and Rheology Enhancer
Abstract: This paper studied the use of coconut fibre as a substitute for caustic soda in drilling fluids for the improvement of pH in a water-based mud. The coconut coir was dried in the sun for 7 hours and ground into very fine particles, after which it was placed in an electronic oven at a temperature of 105°C for 1 hour to remove any remaining moisture. Sieving using a 200 mm …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 3, 2024 · pp. 01–10 Read article
-
Fluidic Engineering: Investigating Cutting Fluids’ Effect on Machined Surface Roughness
Abstract: The primary goal of this experimental study project is to determine the optimal cutting fluid by experimenting with two distinct oil kinds and compositions. Thirty-six compositions of cutting oil are obtained by mixing three distinct oil compositions, such as mineral oil and paraffin oil, with six different additive and anti-foaming agent compositions. Then, using a trial-and-error methodology, we employed these 36 cutting oil compositions for drilling operations with constant pressure …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 2, Issue 1, 2024 · pp. 27–42 Read article
-
Performance Evaluation of Tympanostomus Fuscatus (Periwinkle) Shell Powder as Alternative to Silica Flour in High Temperature Well Cementing Operation
Abstract: The effect of high temperature on cement slurry is a problem in the oil and gas drilling industry. Over the years, silica flour was used to prevent the strength of cement that results from high temperature effect. But, the silica flour is imported and not environmentally friendly. Hence, the need for local material that can serve as alternative becomes imperative. periwinkle shell (Tympanostomus fuscatus) was tested in the laboratory to …
Published in Journal of Petroleum Engineering & Technology · Vol. 15, Issue 2, 2025 · pp. 1–11 Read article