Search
106 articles for “Cure time”
-
Effect of Curing Time on Physico-mechanical Properties on Dental Composite
Abstract: This study aim to investigate the influence of curing time on physical and mechanical properties of a dental composite cured by using LED light with intensity of 1500 mW/cm2 in the range of 440-480 nm. We prepared the glass ionomer powder by fusion of various inorganic components at high temperature and studied the influence of silica/alumina ratio keeping other inorganic salts such as Calcium fluoride (CaF2), Sodium Fluoride (NaF), Calcium …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 36–47 Read article
-
Investigation on Synergistic effect of Carbon Black on Flow properties of EPDM Composite
Abstract: Ethylene Propylene Diene Monomer is one of the most widely used rubbers in automotive exterior sealing systems. It is the material of choice for automotive sponge weather strips around doors, trunks and hoods. Its exceptional air and ozone resistance capabilities, combined with its compounding adaptability, result in high-performing profiles at a low cost, while sealing off water, dirt, and noise for the life of the vehicle. Over the last decade, …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 12, Issue 3, 2021 · pp. 37–48 Read article
-
The Rheological Effect of SiO2 Nanoparticles Additives for NBR/CR Blends
Abstract: The rheological alteration of NBR/CR after adding various nano-quantities of silicon oxide (0–50) wt.% was studied. The rheological properties that were tested are viscosity, scorch time, cure time and max torque. Oscillating disk rheometer was used for measuring the above properties. The experimental results have shown that the silicon oxide additives have a good effect on viscosity and max torque during vulcanization, but at the same time the scorch and …
Published in Journal of Catalyst & Catalysis · Vol. 4, Issue 3, 2017 · pp. 1–4 Read article
-
Geopolymerization: A Review on Physico-chemical Factors Influence to the Reaction Process
Abstract: A geopolymer is one of materials belonging to an inorganic polymer group based on alumino-silicate structural networks. The material is a product of reactions among the activated alumino silicate resources and solutions of alkaline activators in various conditions. There have been many investigations conducted to produce geopolymer using different raw materials and methods. The chemical factors have a decisive role in the reaction process and the formation of the geopolymeric …
Published in Journal of Polymer & Composites · Vol. 8, Issue 3, 2020 · pp. 1–9 Read article
-
Blockchain Enabled IoT System for Tamper Proof Monitoring of Polymer Composite Manufacturing Quality
Abstract: Ensuring real-time process compliance in resin-based polymer composite manufacturing remains a persistent challenge due to non-linear material behaviors, unpredictable curing dynamics, and fragmented sensor data pipelines. Traditional centralized monitoring architectures struggle to guarantee data integrity, auditability, and adaptive response under high-frequency environmental fluctuations. Most existing frameworks fall short in unifying trust, traceability, and time-critical decision-making particularly during critical cure-phase deviations due to limited integration of blockchain with intelligent sensor systems. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 126–145 Read article
-
Effect of Nature of Short Fibers/Carbon Black on Curing Characteristics and Physico-Mechanical Properties of Ethylene Propylene Diene Monomer Rubber Composite
Abstract: AbstractIn this research work, ethylene propylene diene rubber (EPDM) composites were prepared by incorporating the various types of short fibers like cellulose, polyester, p-aramid, m-aramid, cotton short fibers and carbon black on a 2 roll mill. The effect of different short fibers content on the curing characteristics and physico-mechanical properties of EPDM composites were studied. When the loading of carbon black was fixed, it was found that carbon black content …
Published in Journal of Polymer & Composites · Vol. 4, Issue 2, 2016 · pp. 34–43 Read article
-
Experimental Investigation on Strength and Durability Properties of Slag Based Alkali Activated Concrete Incorporating Fly Ash
Abstract: To minimize carbon emissions during cement production and to resolve landfill issues arising from industrial waste, the adoption of alkali-activated concrete (AAC) incorporating various by-products from industry has become increasingly popular as environmentally friendly option to conventional concrete in the construction sector. This study focused on strength and durability of AAC by utilizing waste industrial by-products such as ground granulated blast furnace slag (GGBS) and fly ash (FA) at ambient …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 393–400 Read article
-
Integrate AI and IoT to Develop Sustainable Polymer Structural Materials Processing Optimization: Enabled Monitoring Strategies for Performance and Lifecycle Assessment
Abstract: The need for long-lasting structural polymer materials that are both environmentally friendly and highly mechanically effective is driving demand for these materials as the industrial sector continues to grow. Optimizing processes, saving energy, detecting faults, and monitoring structures are all hindered by conventional polymer manufacture. This study suggests an AI-IoT system for environmentally friendly production of structural polymer materials to get around these problems. Tools for evaluating system performance and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 169–192 Read article
-
Optimization of Resin 3D Printing Process Parameters for Enhanced Dimensional Accuracy and Surface Roughness Using Hybrid Algorithm
Abstract: The advent of 3D printable dental resin has paved the way for minimally invasive dentistry, which helps to retain healthy tooth structure while yet producing pleasing aesthetic outcomes. However, printing these dental resins is being researched to improve their durability and therapeutic efficacy. Frontiers in dental restoration research can aim to fabricate occlusal appliances using resins with optimized parameters for enhanced functionalities. The present study aims to analyze the dimensional …
Published in Journal of Polymer & Composites · Vol. 11, Issue 3, 2023 · pp. 26–37 Read article
-
AI-Driven Optimization of Biopolymer Composite Formulations Using IoT Data Streams
Abstract: Biodegradable polymer composites have emerged as a sustainable alternative to petroleum-based materials in packaging, biomedical, and structural applications. However, traditional formulation techniques for reinforced polymer composites often lack precision and fail to adapt to real-time variations during processing, resulting in suboptimal material performance. This research proposes a real-time AI-IoT-enabled framework to optimize biopolymer composite formulations. The goal is to intelligently tune composite properties such as mechanical strength, moisture resistance, and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 85–100 Read article
-
Performance Evaluation of Tympanostomus Fuscatus (Periwinkle) Shell Powder as Alternative to Silica Flour in High Temperature Well Cementing Operation
Abstract: The effect of high temperature on cement slurry is a problem in the oil and gas drilling industry. Over the years, silica flour was used to prevent the strength of cement that results from high temperature effect. But, the silica flour is imported and not environmentally friendly. Hence, the need for local material that can serve as alternative becomes imperative. periwinkle shell (Tympanostomus fuscatus) was tested in the laboratory to …
Published in Journal of Petroleum Engineering & Technology · Vol. 15, Issue 2, 2025 · pp. 1–11 Read article
-
EXPERIMENTAL STUDY AND ANALYSIS OF COMPRESSIVE STRENGTH IN NOBAKE SAND
Abstract: No bake molds are expendable sand molds, similar to typical sand moulds, except they also contain a quick-setting liquid resin and catalyst. In no bake molding process the moulding sand is poured into the flask and held until the resin solidifies, which occurs at room temperature. It is called as a cold-setting process, as there is no heat involved in it. As a result of this molding process, mold produced …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 2, 2018 · pp. 18–22 Read article
-
Effect of Fiber Addition in Geopolymer Concrete: A Study on Comparison betweenNatural and Artificial Fibers
Abstract: Geopolymer concrete is an inorganic polymer concrete, containing no ordinary Portland cement (OPC). It is produced by reacting alumino-silicate source material with alkaline solution. Geopolymer concrete has highly desirable structural engineering properties, which can lead to significant environmental and economic benefits. Fibers in general and polypropylene (PP) fibers in particular have gained popularity in recent years for use in concrete, mainly owing to their low price and excellent characteristics. Alkalineliquids …
Published in Journal of Structural Engineering and Management · Vol. 2, Issue 1, 2015 · pp. 18–24 Read article
-
Performance Evaluation of Modified Cold Mix Asphalt by Some Waste Materials
Abstract: The aim of study is to evaluate modified CMA volumetric, mechanical and durability properties by some waste materials. Previous studies described that the mechanical properties of CMA are shown to be influenced by different factors including base bitumen grade, porosity of the mix, curing time and additives. The current research is designed to use the waste and by-product materials as filler to enhance the conventional CMA early age strength. Hence, …
Published in Trends in Transport Engineering and Applications · Vol. 3, Issue 3, 2016 · pp. 33–53 Read article
-
Microwave Curing of Glass-Epoxy Composites Using Silica Based Moulds
Abstract: AbstractFor polymer composite product manufacture, curing of the fibre reinforced polymers (FRP) is a critical step in achieving desired mechanical properties. The conventional cure processes involve thermal curing in hot air ovens and autoclaves where the cure process is time and energy intensive. In this context, microwave curing is one of the most promising processing methods since it results in substantially reducing cure cycle time, energy requirements and operational costs …
Published in Journal of Polymer & Composites · Vol. 3, Issue 2, 2015 · pp. 52–57 Read article
-
Phytochemical and In vitro Regeneration Study of Vitex Nirgundo and Piper Betel
Abstract: Medicinal plants have been a major source of therapeutic agents since ancient times to cure human disease. Interest in the revival of natural drugs started in last decade mainly because of the wide spread belief that green medicine is healthier than synthetic products. Despite the major advances in the modern medicine, the development of new drugs from natural products is still considered important. In recent times, interest in plant research …
Published in Research & Reviews : Journal of Herbal Science · Vol. 8, Issue 1, 2019 · pp. 32–38 Read article
-
A Model for Destroying Cancer Cell
Abstract: Cancer is studied in this paper by the optimization technique. By this technique, cancer cell growth rate can be controlled. To minimize the growth rate of the cancer cell is the objective of this paper. The linear programming is used here to control the cancer. An anticancer model is presented in this paper based on linear programming problem. The formulation of anticancer based on the finite decision variables. There is …
Published in Research & Reviews: A Journal of Bioinformatics · Vol. 8, Issue 3, 2021 · pp. 1–4 Read article
-
DURABILITY ASSESSMENT OF SELF COMPACTING, SELF CURING CONCRETE INCORPORATING CRUSHED ROCK POWDER AND MINERAL ADMIXTURES
Abstract: Curing plays a crucial role in achieving the desired strength, characteristics, and durability of concrete. Negligent curing practices can lead to adverse effects on hydration and mechanical properties of concrete. In recent times, self-curing concrete has gained significant attention due to its potential in reducing water loss through the use of self-curing agents. The Present Research study focus on investigation on durability characteristics of self-curing self-compacting concrete using crushed rock …
Published in Journal of Polymer & Composites · Vol. 11, Issue 10, 2023 · pp. 25–35 Read article
-
Influence of Waste Marble Powder by Partially Replacement of the Cement with M30 Grade to form Green Concrete
Abstract: This paper presents the study of concrete mix design using marble powder. Along the rapid growth of human needs in many sectors, a significant decrease in the availability and viability of the natural resources was always faced. Leaving the waste materials to the environment directly can cause environmental problem. Hence the reuse of waste material has been emphasized. The use of waste marble powder (dust) was proposed in partial replacement …
Published in Journal of Construction Engineering, Technology & Management · Vol. 8, Issue 2, 2018 · pp. 28–32 Read article
-
Cancer Diagnosis by Functional Possibilities and its Applications
Abstract: This paper presents a diagnosis of cancer by the theory of function. Some properties are applied for the same. The injective, surjective and bijective mappings are used for curing the cancer disease. Inverse function also plays an important role. The set of possibilities of functional properties are proved as the particular map between the cancer cell and medicine is required to measurable cure. To curing cancer is primary objective of …
Published in Research and Reviews: Journal of Oncology and Hematology · Vol. 11, Issue 1, 2022 · pp. 1–4 Read article