Search
372 articles for “Pulses”
-
Design and Implementation of an Automatic Rain Sensing Wiper System Using SEN0545 Sensor and Raspberry Pi Pico W
Abstract: This study presents the design and development of an intelligent, automatic rain-sensing wiper system designed to enhance vehicle safety. The system utilizes a SEN0545 capacitive rain sensor, integrated with internal signal processing, and a Raspberry Pi Pico W microcontroller as its central control unit. The proposed approach enables non-contact and corrosion-free rain detection, ensuring reliable performance under varying environmental conditions. Based on the detected rainfall intensity, the controller dynamically adjusts …
Published in Trends in Electrical Engineering · Vol. 16, Issue 2, 2025 · pp. 16–25 Read article
-
Performance Analysis of LCI and VSI Fed Induction Motor Drive
Abstract: In this paper combination of a load-commutated inverter (LCI) and a voltage-source inverter (VSI) are employed for performance analysis of induction motor drive. Performance of the drive has been evaluated through the different variation in reference speed and load torque. proposed LCI-based induction motor drives include the following Advantages: (1) sinusoidal motor phase current and voltage based on the instantaneous motor speed control; (2) fast dynamic response by the VSI …
Published in Journal of Control & Instrumentation · Vol. 12, Issue 1, 2021 · pp. 29–44 Read article
-
Investigation of Physical Characteristics and Machining Parameters of Improved Al-SiC MMC Using Dry EDM Process for Aerospace Industries
Abstract: Aluminium-based composite is widely used in aerospace and automobile industries because it is lighter in weight; but the trouble is that it is easily worn-out and life of the components is decreased. To overcome these problems, aluminium silicon carbide composite material has been developed with good wear-resistance, hardness and lighter weight. Silicon carbide has good mechanical properties like wear resistance, hardness, toughness and high melting point. Silicon carbide weight fractions …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 1, 2018 · pp. 15–32 Read article
-
Optimization of Process Parameter in Electrical Discharge Machining
Abstract: This is the non-traditional machining process. The high surface finish of the material is required. More complex shape of material is required. Wire EDM is one of the nontraditional machining processes. Surface roughness and kerf width are of crucial in the field of machining processes. This paper uses the Grey relational theory and Taguchi optimization technique, in order to optimize the cutting parameters in Wire EDM for D3 steel material …
Published in Journal of Experimental & Applied Mechanics · Vol. 11, Issue 2, 2020 · pp. 4–10 Read article
-
Smart Programmable Energy Meter with Bill Estimation
Abstract: The idea of a rechargeable electricity energy metre, similar to how we recharge our mobile phones, is a smart one. In this project, we are developing a computerised system using a microcontroller called the 8051 and a GSM module. The project's major goal is to create an energy metre that sends SMS notifications to consumers to let them know exactly how much energy each load is consuming and how much …
Published in Journal of Electronic Design Technology · Vol. 14, Issue 1, 2023 · pp. 15–20 Read article
-
Optimizing Fusion Zone Grain Size, Hardness and Tensile Strength of Micro Plasma Arc Welded Titanium (Ti-6Al-4V) Alloy Using Grey Relational Analysis
Abstract: In the present work, Titanium (Ti-6Al-4V) alloy sheet of 0.5 mm thick is butt welded using Micro Plasma Arc Welding. Welding input parameters like peak current, base current, pulse rate and pulse width are considered and output responses like fusion zone grain size, hardness and ultimate tensile strength of the welded joint are considered. Taguchi L25 orthogonal matrix is adopted by considering four factors and five levels of weld input …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 2, 2018 · pp. 21–33 Read article
-
Optimization of WEDM Process Parameters Using a Hybrid Multi-Criteria Decision Making Approach
Abstract: The effectiveness of the manufactured parts is typically measured by more than one performance characteristics. Hence the manufacturing engineers frequently experience the difficulty in optimizing the multiple responses at a time. The present work is to explore the effect of wire electrical discharge machining (WEDM) process parameters in machining of Aluminum metal matrix composite (AMMC). The multiple performance characteristics of material removal rate (MRR) and surface roughness (Ra) are optimized …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 3, 2018 · pp. 24–30 Read article
-
Analysis of Machining Parameters in Wire EDM with Aluminum Alloy Using PCA and TOPSIS Approach
Abstract: Although the efficiency of traditional cutting processes is inadequate by the mechanical properties of the processed material and the intricacy of the work piece geometry, electrical discharge machining (EDM) being a thermal erosion process, is subject to no such limitations. This paper summaries the suitable use of Taguchi’s L27 orthogonal array which takes 27 experimental runs to develop a mathematical model for correlating the interactive and higher order impacts of …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 2, 2017 · pp. 1–11 Read article
-
An Experimental Study to Determine Optimum Machining Conditions for Electrical Discharge Machining of the Heat Treatable Steel 42CrMo4 (Din 1.7225)
Abstract: Electric discharge machining (EDM) is a well-established machining option and a non-traditional machining process, in many manufacturing-related industries worldwide. It is found to be capable of machining geometrically complex or hard material components, which are specific and difficult-to-machine. In this study, the electrical discharge machining of 42CrMo4 with different electrode materials namely, copper, aluminum and tungsten carbide and process parameters was performed to explore the influence of EDM parameters on …
Published in Journal of Mechatronics and Automation · Vol. 2, Issue 2, 2015 · pp. 23–32 Read article
-
Enhancement of Power Quality in a DG-Integrated Smart Grid Using UPQC
Abstract: The goal of this presentation would be to demonstrate how an upqc conditioner may be used to improve the strength of a dispersed energy (DG) system (UPQC). Despite the potential advantages of DG, which include increased energy supply, reduced power system growth, and environmental friendliness, there are numerous problems assimilating DG into the system or sustaining it in standby mode. Voltage profile (PQ) is a significant technological barrier in dispersed …
Published in Journal of Microcontroller Engineering and Applications · Vol. 9, Issue 1, 2022 · pp. 29–34 Read article
-
Review on Photoconductive Antenna Design from Conventional to Microstructures
Abstract: Semiconductors possess many diverse phenomena under terahertz-frequency electromagnetic radiation (THz). This is due to the fact that the energy of THz photons is at quite large scales in case of bulk and low-dimensional materials and devices. With regard to broadband THz sources, various inorganic crystals such as ZnTe/GaP/GaAs/GaSe/DAST/LiNbO3 have been used which are pumped by femtosecond laser pulses. These pulses are combined with field-resolved detection through electro-optic sampling using similar …
Published in Journal of Microwave Engineering and Technologies · Vol. 9, Issue 1, 2022 · pp. 1–8 Read article
-
Optimization of Machining Parameters in Electric Discharge Machining of Al 65032
Abstract: Electric discharge machining has the potential to maintain surface topography and produce less stresses and destruction to the components. In this machining there is no contact between the tool and the work piece. The spark generated due to the electrostatic field generation between tool and the work piece. The objective of this experimentation was to create guidelines for electric discharge machining of Al 65032. Aluminum alloy 65032 is one of …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 3, 2015 · pp. 15–22 Read article
-
Parametric Optimization of Tool Wear Rate in Side Flushing form of Die Sink EDM of EN-31 Die Steel
Abstract: Electrical discharge machining (EDM) is one of the most extensively used non-conventional material removal processes for manufacturing geometrically complex or hard material parts that are extremely difficult to machine by conventional machining process. EDM researchers have concentrated on achieving faster and more efficient metal removal rate coupled with a reduction in tool wear and improved surface characteristics. In this paper, the operating performance measures of side flushing type of electrical …
Published in Journal of Materials & Metallurgical Engineering · Vol. 1, Issue 1-3, 2011 · pp. 72–80 Read article
-
Optimization of Process Parameters for AISI 304 Using Micro-EDM Drilling Process: A Review
Abstract: Today, a variety of microparts are needed to fabricate high-tech items including MEMS applications and micro-electronic parts. The advancement of micromachining technology becomes ever more important in order to produce these micro parts. The creation of accurate holes and pins is one of themultiple processes in the micromachining process that is necessary for many small components. In order to create deeper, more straight holes, micro-hole drilling is utilized in a …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 3, 2023 · pp. 26–37 Read article
-
Harmonic Analysis of Single Phase Inverter
Abstract: AbstractIn this paper, study is carried out to investigate the THD of various voltage control signal techniques for single phase PWM inverter. The inverter is implemented using three pulse width modulation techniques- unipolar PWM, modified sine PWM and harmonic injection modulation. The performance of these control schemes are evaluated through simulation in MATLAB/SIMULINK. The obtained THD and fundamental magnitude of the output AC is tabulated.Keywords: Single phase inverter, pulse width …
Published in Journal of Microelectronics and Solid State Devices · Vol. 5, Issue 2, 2018 · pp. 20–28 Read article
-
Novelty of Cascaded Inverter Based Two Stage Power Conditioning Systems for Constant Wind Power Applications
Abstract: Wind energy has proved to be the most promising renewable energy source because of its environmental friendly nature. Wind energy can be generated by harnessing the kinetic energy of atmospheric air. The present concern towards wind turbines is to increase the size of turbine in order to harvest more energy and also to reduce cost of per megawatt capacity. This paper proposes a 2-stage power conversion technique. The first stage …
Published in Journal of Power Electronics and Power Systems · Vol. 6, Issue 1, 2016 · pp. 1–11 Read article
-
Harmonic Compensation in Grid Interconnected DG Units by Closed Loop Control
Abstract: This paper deals with improvement of power quality problem namely harmonic problem using distributed generation as their source of electricity. The harmonics occur in such a system because of the nature of loads connected. There are many power quality problems; out of which harmonics normally caused by nonlinear loads like variable frequency drives, fluorescent lightning, office computers etc. have adverse effects on the power quality. Also, harmonic detection and prediction …
Published in Journal of Power Electronics and Power Systems · Vol. 7, Issue 1, 2017 · pp. 9–17 Read article
-
Circuit Topologies, Operation, Control Schemes and Modulation Techniques of Modular Multilevel Inverter
Abstract: The Modular Multilevel Converter (MMC) is one of the developing topology. MMC has several attractive features such as a modular structure, transformer-less operation, easily scalable in terms of voltage and current, low expense for redundancy and fault tolerant operation and excellent output waveforms quality. Due to these attractive features industry and researcher increased the interest in this converter. This interest results in the development of new power topologies, modulation strategies …
Published in Journal of Power Electronics and Power Systems · Vol. 7, Issue 1, 2017 · pp. 28–40 Read article
-
A Modular Three Phase AC Voltage Controller for Induction Motor
Abstract: AbstractThree phase induction motor (IM) is widely used in the industries because of rugged construction. User needs to control speed of the motor depending on the desired speed and application. In this paper launching of speed control of 3-phase IM is controlled by 3-phase AC voltage controller by varying the voltage by pulsewidth modulation (PWM) technique. In olden days speed control was possible for DC motors only, but with the …
Published in Journal of Power Electronics and Power Systems · Vol. 3, Issue 3, 2013 · pp. 1–5 Read article
-
Analysis and Implementation of Carrier Based and Space Vector PWM Techniques on a Three-Phase Voltage Source Inverter
Abstract: This paper presents a comprehensive analysis of carrier based and space vector pulse width modulation (PWM) techniques on a two-level three-phase voltage source inverter (VSI). The results of simulations performed in Matlab/Simulink are compared to the results obtained from the implementation of the PWM schemes on an actual VSI whose PWM signals are generated using dSpace. The analysis of the inverter line to line voltages includes, a fast fourier transform …
Published in Journal of Power Electronics and Power Systems · Vol. 5, Issue 3, 2015 · pp. 125–139 Read article