Search
271 articles for “predominant”
-
Enhancement of Electrical Conductivity of Laterite Derived Ferric Oxide to Facilitate As Anode Materials
Abstract: Laterite is a mineral abundant in ferric oxide and various impurities, including aluminum oxide and silicon dioxide. The extraction of ferric oxide from laterite is accomplished through a cost-effective leaching process employing HCl, NaOH, and Sodium dodecyl sulfate (SDS). Characterization using Xray diffraction (XRD) confirmed the synthesized particles to be α-Hematite nano particles, with an average particle size of 94.21 nm, predominantly falling within the range of 90 nm to …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 3, 2023 · pp. 1–11 Read article
-
Evolutionary Particle Swarm Optimization (EPSO) based technique considering Voltage Stability Margin for Reactive Power Reserve Optimization
Abstract: Reactive power reserve and voltage stability are one of the important parameters required for proper operation of the electrical power system. Voltage stability covers a broad span of phenomena in power systems and its applications. Voltage stability is defined as ability of power system to assist fixed bearable potential at every single bus of the system under standard operating conditions and when put through to a disturbance. At any instant …
Published in Journal of Power Electronics and Power Systems · Vol. 11, Issue 2, 2021 · pp. 36–41 Read article
-
Review on: Plastic Waste Uses for the Production of Liquid Oil
Abstract: Solid waste is a substantial problem, predominantly in emerging countries that lack adequate substructure and operational land mass to process it in a corrected manner. Several emerging nations are facing a combination of issues that avert proper management of solid waste. This paper reviews the management of municipal solid waste in Ethiopia, using the Addis Ababa City as a case study. The consumption of plastic materials is vast and has …
Published in Journal of Petroleum Engineering & Technology · Vol. 9, Issue 3, 2019 · pp. 28–33 Read article
-
Water/Oil Cresting Optimization in Horizontal Wells: Experimental Study
Abstract: In recent years, the application of horizontal wells has been predominant and successful in minimizing cresting scenarios due to significant reservoir exposure of its laterals. Cresting is a natural phenomenon known to occur when an imbalance of viscous and gravitational forces exists in a reservoir. This study experimentally investigates the effect of varying the inclined section of the horizontal well using a simple, practical and inexpensive cresting optimization technique. The …
Published in Journal of Petroleum Engineering & Technology · Vol. 10, Issue 3, 2020 · pp. 35–46 Read article
-
Review on Chemical Separation of Crude Oil and Analysis of Its Components
Abstract: Crude oil is chemically composed of a complex mixture of hydrocarbons of different gaseous, liquid and solid states, the total of which may reach more than 17,000 organic compounds. At standard conditions of pressure and temperature the light hydrocarbons with carbon numbers 1 to 4 (methane, ethane, propane, butane) are present in gaseous form; Whereas pentane and the heavier hydrocarbons are found in liquid form, and in the heavy fractions …
Published in Journal of Petroleum Engineering & Technology · Vol. 11, Issue 2, 2021 · pp. 35–49 Read article
-
Review-Value Stream Mapping to Increase Productivity
Abstract: Value stream mapping (VSM) is one of the predominant tools of lean methodology to identify waste in production, business and manufacturing by recognizing and removing redundant activities. This map helps us to detect the redundant activity in the entire process line by which we can eliminate it. The existing process steps are scrutinized to reduce the process steps up to the fewest necessary steps. By the consequence, redundant time will …
Published in Journal of Production Research & Management · Vol. 6, Issue 1, 2016 · pp. 16–18 Read article
-
Overview of Banking Industry with Special Reference to Reforms in the Indian Banking System
Abstract: The liberalization, privatization and globalization phase of 1991 popularly known as LPG policy changed the face of Indian economy. Reforms took place in several sectors of the economy; predominantly it affected the Indian banking industry. The role of banking industry is extremely important for the growth of any economy and India being a developing country is no exception to this rule. This paper discusses the overview of Indian financial system, …
Published in Journal of Production Research & Management · Vol. 6, Issue 3, 2016 · pp. 1–12 Read article
-
Complementary Metal Oxide Semiconductor Readout Integrated Circuit for Imaging Applications
Abstract: In this paper presents a novel continuous-time simultaneous-readout scheme for active imaging systems based on orthogonal modulation of photo detector signals. The superimposed-continuous-time approach presented here differs from the conventional scheduled-discrete-time scheme in that the photo detector signals are summed in a common bus concurrently and then converted to voltage levels for digitization. We illustrate that our proposed architecture may be profitable. Predominantly, in solicitations, the bandwidth necessities for a …
Published in Journal of Semiconductor Devices and Circuits · Vol. 2, Issue 2, 2015 · pp. 5–8 Read article
-
Low-Velocity Impact Behaviour of 3d Printing Techniques Using Fiber Reinforcement Polymer Composites: A State of the Art Review
Abstract: Additive manufacturing (AM) is one of the pioneering fields of composite manufacturing, not only in the fabrication of composite all other emerging fields also utilize this technology. Fibers are one of the predominant reinforcing agents which are used to fabricate composite materials for many applications. This review article provides a detailed discussion about the role of 3D printing technology using fiber-reinforced composites in low-velocity applications. 3D printing technology provides very …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 8, Issue 2, 2021 · pp. 1–7 Read article
-
Complex-hole Polishing Combining Abrasive Gels and Abrasive Flow Machining
Abstract: Abrasive flow machining (AFM) makes it simple to polish the intricate holes and the curved surfaces of difficult-to-machine geometries because abrasive media may bend flexibly in this process. Although abrasive media predominate in the polishing behavior of the AFM process, the mechanism of the abrasive media is difficult to grasp due to the highly viscous gels; as a result, many finishing tasks require a lot of time to design the …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 10, Issue 1, 2023 · pp. 6–9 Read article
-
Modelling of Skin Effect in On-Chip VLSI RLC Global Interconnect
Abstract: This paper addresses one of the aspects of the high frequency effects, namely the skin effect. The basicproblem with skin effect is that it attenuates the high frequency components of a signal more than that ofthe low frequency components. Due to the increase in operating frequency and die sizes, RC models arebecoming insufficient for analysis of global VLSI interconnects. Accurate noise modelling for RLC lines isthus critical for timing and …
Published in Journal of VLSI Design Tools and Technology · Vol. 1, Issue 1-2-3, 2011 · pp. 31–44 Read article
-
Numerical modeling of Nocardia Migration Influenced Transport pressured by Dispersion and velocity in Fine Sand Formation in Wetland Environment
Abstract: AbstractThis paper monitor the behaviour of Nocardia in fine sand deposition, the study express the velocity and dispersion influences on Nocardia migration in wet land environment. The transport process at different litho structure observed variation on their concentration in the study area, this condition developed fluctuation on the transport system within the predominant strata, the concentration from three to thirty metres developed fluctuation base on the influences from dispersion and …
Published in Journal of Water Resource Engineering and Management · Vol. 5, Issue 1, 2018 · pp. 6–13 Read article
-
MODELING AND SIMULATION OF LEGIONELLA TRANSPORT INFLUENCED BY HETEROGENEOUS VELOCITY IN STREAM
Abstract: The purpose of this study is to monitor the behaviour of legionella contaminant in stream, the rate of concentration at different monitoring station developed various rate of effect on the water bodies, heterogeneous velocity of flow in the stream was observed as the major sourced of change in concentration at different stations, the expression from the system developed the derived solution to evaluated the behaviour of the contaminant at different …
Published in Journal of Water Resource Engineering and Management · Vol. 6, Issue 2, 2019 · pp. 29–35 Read article
-
Hyphomicrobium Transport in Heterogeneous Coarse Formation Influenced by Porosity
Abstract: Hyphomicrobium transports were monitored at different litho structure in deltaic depositions. The study is to determine their rates of migration in heterogeneous predominant porous medium in the study area. The deposition of Hyphomicrobium migration experienced lag phase in some region of the formation. Fluctuation was also observed base on the reflection of heterogeneous porosity. The migration in shallow depth may also be affected by high acidic [PH] in the soil …
Published in Journal of Water Resource Engineering and Management · Vol. 5, Issue 3, 2018 · pp. 25–33 Read article
-
MODELLING HETEROGENEOUS POROSITY IN ALLUVIA PLAIN DEPOSITION IN DELTAIC FORMATION
Abstract: Abstract Porosity of soil are basically determine for various purpose, but this papers monitor degree of porosity in alluvia plain deposition under heterogeneous lithostratification, the study examine the predominant deposition of heterogeneous porosity in alluvia plain, such condition were observed in deltaic environment, such heterogeneous degree of porosity will definitely affect other engineering soil properties, this paper try to effectively investigate and determination of total evaluation for such heterogeneous porosity …
Published in Recent Trends in Civil Engineering & Technology · Vol. 8, Issue 2, 2018 · pp. 1–10 Read article
-
PREDICTING THE BEHAVIOUR OF BORRELIA IN HOMOGENEOUS FINE SAND IN COASTAL AREA OF BAKANA
Abstract: AbstractThe deposition of borrelia in fine sand formation in the coastal area of Bakana was monitored applying modeling and validation, the study try to predict the migration process of borrelia in the coastal formation, such deltaic depositions were observed to be alluvia predominant thus maintained homogenous fine sand formations. The study monitor the transport of borrelia in coastal area to observed whether the homogeneity will affect the behaviour of borrelia …
Published in Recent Trends in Civil Engineering & Technology · Vol. 8, Issue 2, 2018 · pp. 11–19 Read article
-
Explaining the Cost Performance and Maturity of Transportation Infrastructure in the Developed and Developing World: One Size Fits All?
Abstract: AbstractScholarly text analysing the financial performance of highway projects are evident in the literature, most of which have opined that highway agencies record higher levels of cost overruns compared to other clients of construction and building works. Similar assertions are made about the relatively higher levels of cost overruns recorded on highway projects executed in the developing world. A scant number of seminal works have emerged in the literature, offering …
Published in Recent Trends in Civil Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 33–42 Read article
-
Strength and Durability Properties of Metakaolin Amalgamated High Performance Concrete
Abstract: In past three decades, it is inevitably for the development of high strength concrete (HSC) and high performance concrete (HPC) is progressively enhanced, since these concrete are widely used throughout the world in most prominent projects like oil, bridges, multi-storey buildings and nuclear industries etc. In meticulous, the amalgamation of supplementary cementing material (SCM) or pozzolanic materials is vital when high strength and durability become the most desired properties of …
Published in Recent Trends in Civil Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 36–44 Read article
-
Experimental Investigation on the Effect of Manufactured Sand in Concrete
Abstract: Concrete is the most widely used construction material owing to its versatile nature. Three fourth of the concrete is made of aggregates, amongst which fine aggregate has massive demand. River sand is the predominantly used fine aggregate, which is under significance because of the increased demand and less availability. The continuous mining of river sand has also affected the environment; ecologically and economically. Manufactured sand offers viable alternative to natural …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 1, 2016 · pp. 45–52 Read article
-
Utilization of Agricultural Waste for Defluoridation of Water: A Review
Abstract: Fluoride is an essential micronutrient for human health which can be obtained from food items. Excess fluoride is one of the anionic, inorganic contaminants, found predominantly in ground water due to weathering of rocks, geochemical reactions or anthropogenic activity such as disposal of industrial wastewaters, because of which removal of excess fluoride is mandatory. Among various methods used for defluoridation of water, adsorption is widely used. It is more remarkable …
Published in Recent Trends in Civil Engineering & Technology · Vol. 5, Issue 2, 2015 · pp. 23–29 Read article