Search
988 articles for “rate”
-
Fracture Analysis of FRP Composites under Thermo-Mechanical Loads for Different Geometry Cutouts
Abstract: Fiber-reinforced composites (FRPs) are used extensively in structural and non-structural components of the aerospace and automotive industries. To utilize these materials for structural applications, it is necessary to understand the fracture behavior of the material. In the present investigation of carbon fiber laminates, studies were carried out to understand the fracture toughness characteristics of the carbon fiber laminates with mechanical, thermal, and thermo-mechanical loadings of modes I, II, and III. …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 1–10 Read article
-
Optimizing Parameters for Dry Sliding Wear Control in Stir-Cast AA7050/SiC Composites
Abstract: Using a pin-on-disc tribometer, this study examined the dry sliding wear behavior of AA7050/SiC composites. The production of this metal matrix composite was achieved through the stir-casting process, which involved an initial step of melting the AA7050 alloy, followed by the careful introduction of silicon carbide (SiC) particles, stirring to achieve uniform dispersion, and finally, casting the molten mixture. Wear rate (WR) was determined by three operational parameters: SiC reinforcement …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1624–1635 Read article
-
Experimental Assessment and Statistical Argument of Al-Si/CSA/MoS2 Hybrid Composites for Mechanical and Tribological Characteristics
Abstract: To augment the mechanical and tribological properties of Al-Si matrix composites complement with molybdenum disulphide (MoS₂) and coconut shell ash (CSA), a mixed experimental and Face-Centered Composite (FCC)strategy was employed. A liquid metallurgical method called stir casting was used to create hybrid composites with 5–15 wt.% CSA and 1–3 wt.% MoS₂. A FCC experimental design with thirty runs was used to thoroughly evaluate the materials. This design allowed for the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 792–802 Read article
-
Monitoring the Effectiveness of Water-Based Plants for the Inhibition of Metal
Abstract: The temperature performance profile of the plant extracts shows that inhibition efficiency increased with increasing temperature of the system until at about 323K at 9.00hrs immersion time where a decline in inhibition efficiency occurred implying the opposite at higher temperatures and longer immersion time. Corrosion rate parameters changed with rise in temperature and exposure – immersion time. Plots of rates of corrosion against the volume(s) of the test inhibitor(s) in …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 13, Issue 1, 2026 · pp. 37–47 Read article
-
Epidemiological Study of The Microbial Causes of Diarrhea in Children in Najaf Governorate, Iraq
Abstract: The current study included a survey of the microbial causes of diarrhoea among children attending Al- Zahra Teaching Hospital for Maternity and Children in Najaf Governorate and Al-Furat Al-Awsat Hospital in Kufa District. 150 samples were collected, ranging in age from one day to seven years, over a three-month period, from 1/10/2024 to 30/12/2024. The direct swab and stool concentration method was used to examine the stool. The results showed …
Published in International Journal of Pathogens · Vol. 3, Issue 2, 2026 · pp. 9–14 Read article
-
LoRa and LoRaWAN in the IoT: Performance, Challenges, and Future Opportunities
Abstract: This paper provides a broad overview of both LoRa and LoRaWAN technologies in the context of Internet of Things (IoT). The market need for communication technology to be low-power and long-range continues to grow, and LoRa and LoRaWAN are emerging as viable options for enabling widespread IoT applications in a variety of applications. This review offers structured and comparative assessment of their functionality in different environments, such as urban, rural, …
Published in International Journal of Wireless Security and Networks · Vol. 4, Issue 2, 2026 Read article
-
Additive Manufacturing of Polymer-Based Advanced Composites: Mechanical Properties and Performance Evaluation
Abstract: Fabrication of large-scale and geometrically complex polymer-based advanced composites via fused deposition modelling (FDM) has been shown to be a promising technology for the production of such materials, however there are challenges in using short carbon fibre-reinforced polylactic acid (CF-PLA) which include obtaining high mechanical performance and maintaining dimensional accuracy with dynamic robot motion and complex interactions occurring between process parameters. The conventional approaches are mostly static feed rates or …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1326–1335 Read article
-
Smart Jacket for Health Monitoring and Controlling
Abstract: Due to drastic changes in climatic conditions, winters are getting much colder, summers are getting much hotter. Uttermost hot or cold conditions are greater threat to health. These circumstances might cause genuine medical problems. At very high temperature most common problem is heart attack and overcooling of body is major problem during extreme colder conditions. As the application of technology has increased in every sector, it has also been introduced …
Published in Journal of Control & Instrumentation Read article
-
Solar Powered Irrigation System Design with Venturimeter for Utilizing Natural Resources
Abstract: This research focuses on enhancing crop productivity in agriculture by ensuring high quality and quantity of crops. Crops needs to be given adequate nutrients in an efficient and timely fashion as a way to accomplish this.. Thus, liquid-based fertilizers are selected for this purpose. However, farmers often face challenges in supplying fertilizers with the required quantity and precision. To address this issue, we propose a solution that leverages solar energy …
Published in International Journal of Energy and Thermal Applications · Vol. 1, Issue 1, 2023 · pp. 29–35 Read article
-
Study on the Variations in Physicochemical Property Concentration in a Contaminated Fresh and Salt Water
Abstract: In this research, the dispersion of crude oil contaminated was subjected into laboratory observations and results were recorded. These results were used to develop and adopt mathematical models for a proper engineering experimental practice. 1.5m3 volumes of fresh water and salt water were filled in two tanks of equal fit at the same intervals along the tanks and depth, where samples were collected for the purpose of analysis of physicochemical …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 1–9 Read article
-
Optimal Abrasive Jet Machining Parameters for Glass Fiber Reinforced Plastics
Abstract: Abrasive jet machining (AJM) is a best choice for processing of glass fiber reinforced plastics (GFRP). Inherent to the nonlinear behavior of performance characteristics during repeated experiments are inevitable variations, attributed to measurement errors and unknown influencing input variables. This study employs the Taguchi method with an orthogonal array to systematically identify optimal input variables through a limited number of experiments. The paper introduces a direct and reliable Taguchi-based multi-objective …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 247–255 Read article
-
Impact of Tool rotating speeds on the Mechanical characteristics of dissimilar friction stir-welded AZ80A-Mg – AA6061-Al joints
Abstract: In this investigation, separate AA6061-Al and AZ80A-Mg alloy plates were effectively joined through stir welding with friction. We looked closely at the weld joints' characteristics, especially their mechanical aspects. In the experiment, here were multiple tool rotating rates (rpm) of 800, 1000, 1200, 1400, and 1600 used. A cylindrical pin-equipped tool featuring a tapered profile was utilized, inserted into the AA6061 alloy plate is offset by 0.5 mm, while maintaining …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 161–168 Read article
-
Experimental investigation of humidification-dehumidification desalination system
Abstract: The aim of present study is to investigate an H-DH desalination system experimentally. The system consists of a solar air heater, a humidifier, and a dehumidifier connected with an evaporative cooler. The proposed system is operated in a closed loop configuration, at two airflow rates. The performance metrics are assessed via the examination of energy and economic factors. The solar air heater has the ability to produce hot air with …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 104–113 Read article
-
CFD Analysis of Electric Vehicles Battery Pack: A Research Study
Abstract: The goal of the project is to keep the battery temperature within the specified range and to improve the battery pack's performance under different temperature settings. To achieve these goals, we employ software to analyze the data and provide the necessary output. With model-based design, you can understand the dynamic behavior. For this project, a CAD model was produced with Creo Parametric. We used the STAR CCM+ Software for analysis …
Published in International Journal of Electrical Power and Machine Systems · Vol. 1, Issue 2, 2023 · pp. 28–32 Read article
-
Sliding Mode Controller-based Load Frequency Regulation for a Two-area Interrelated Power System
Abstract: This study presents the use of the sliding mode control approach for power systems load frequency regulation. A sliding mode load frequency controller is part of a two-area power system. Both reheat and non-reheat. These two regions each have a distribution of thermal turbines. Nonlinearities such as governor dead region and production rate limitations are included in the block diagram of a power plant model. Our control objective is to …
Published in International Journal of Advanced Control and System Engineering · Vol. 1, Issue 2, 2023 · pp. 8–13 Read article
-
Tribological Study on SiC+Graphene Reinforced Al319 Composite andOptimization of Stir Casting Parameters
Abstract: The aluminium 319 (Al319) is a commonly used material for fabricating automobile components. Due to continuous friction and vibration, those components are subjected to significant wear. Therefore, it is necessary to improve the wear characteristics of this Al319. Hence, in this study Silicon Carbide (SiC) and Graphene nanoparticles (GNPs) are reinforce to Al319 via electro-magnetic stir casting method to optimize wear characteristics without its affecting mechanical properties. Various proposition of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 105–123 Read article
-
Evaluation of Temporal Distribution of Recurrent Cholera Outbreak in Zambia.
Abstract: Background: Cholera cases in Zambia have been observed over a period without understanding the epidemiological cycles. The aim of the study was to evaluate the temporal distribution of recurrent cholera outbreak in Zambia from 1977 to 2019. Methods: Cholera case records of both sex and all ages were retrospectively analyzed. The primary source documents were reviewed including infectious diseases line list, notifiable diseases reports, Health Impact Assessment, District Health Impact …
Published in Recent Trends in Infectious Diseases · Vol. 2, Issue 1, 2025 · pp. 10–21 Read article
-
Hybrid Beamforming Strategies for mm-wave Massive MIMO System
Abstract: Hybrid analog and digital beamforming (HBF) has emerged as a compelling solution for millimetre-wave (mm-wave) communication systems, addressing the need for efficient beamforming while minimizing hardware costs and power consumption. We optimise HBF for mm-wave Massive MIMO systems in the present article. Using the Spectral efficiency and bit rate error as the performance metrics to assess transmission reliability. To reduce computational complexity, we introduce a low-complexity singular value decomposition and …
Published in Journal of Microwave Engineering and Technologies · Vol. 12, Issue 1, 2025 · pp. 22–28 Read article
-
Evaluation of Medication Adherence in Patients with Type 2 Diabetes Mellitus: A Mixed- Methods Approach
Abstract: Background: Medication adherence refers to how closely an individual follows the prescribed medication regimen. It is essential for achieving desired therapeutic outcomes and improving patient health. Inadequate adherence can result in the deterioration of health conditions, higher mortality rates, and increased healthcare expenses. Diabetes mellitus, being a chronic condition, demands ongoing medical care not only to prevent the onset of serious complications but also to manage them effectively once they …
Published in International Journal of Community Health Nursing And Practices · Vol. 3, Issue 1, 2025 · pp. 28–35 Read article
-
Experimental Investigations of EDM Parameters on Machining Square Blind Holes in Maraging Steels
Abstract: Square blind holes have certain qualities that make them useful in fields where accuracy and efficiency are crucial, like aerospace, automotive, molding, and general manufacturing industries where structural integration is required in precise assembly. It is challenging to machine square blind holes with traditional machining due to geometrical complexity as precision is required for sharp corners which is difficult to get at the corners due to tool wear. Electrical discharge …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 390–397 Read article