Search
983 articles for “DRA”
-
Aerosol to Suggest Climate Delineation
Abstract: Marine aerosol of submicron sized biogenic originated organic fraction is subtending persistently constitutively compared to drastic variation based on volcanic eruptions. Sulphur is studied to form acid aerosol where the basic constituent in the stratosphere is reduced comparatively. High concentrations of organic fraction have been found from aerosol in marine boundary layer (MBL). Marine aerosol chemical composition has been influenced by the yearly biological cycle of the ocean, and so …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 11, Issue 2, 2021 · pp. 51–58 Read article
-
Perceptions of Modular Construction as a tool for incorporating Resilience in Post Disaster Housing Reconstruction in the Niger Delta Environment
Abstract: The Niger Delta region of Nigeria is coastal in nature and its urban form is governed by natural environmental constraints that have a strong bearing on the available land for physical development and the cost of provision of housing. The study espouses the adoption of a modular off-site prefabricated system of construction to close the enormous gap between demand and supply for housing in this ecologically fragile environment. This prescriptive …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 12, Issue 3, 2022 · pp. 1–7 Read article
-
Landslide Risk Assessment in Kodagu District, Karnataka: A Case Study
Abstract: AbstractIn this study, an attempt has been made to assess the landslide risk zones using a GIS based weighted linear overlay method with Satty’s analytical hierarchical process to maintain consistency for assigning rank and weight for following factors includes geology, geomorphology, rainfall, soil, road density, drainage density, and topographic triggering factors such as slope and aspects are taken as input for assessment of landslide risk.Thus the technique used in landslide …
Published in Journal of Geotechnical Engineering · Vol. 4, Issue 3, 2017 · pp. 19–34 Read article
-
TRANSFORMATION OF INHERITED ENGINEERING PROPERTIES OF SOIL DUE TO STUBBLE BURNING - A CASE STUDY
Abstract: Stubble Burning has put the state government as well as central government in deep thoughts. The smoke that emits from the farms comes in contact with the breeze to become smog that collectively moves southward affecting the entire belt of northern India including Delhi. Sometimes it becomes too difficult to breathe and public is forced to use breathing masks to avoid poisonous gas entering into their lungs. Research says inhaling …
Published in Journal of Geotechnical Engineering · Vol. 5, Issue 3, 2018 · pp. 31–36 Read article
-
Analysis and Design for Homogeneous Earth Slopes
Abstract: In an aspect of geotechnical engineering problems, slope stability is a condition of inclined soil, waste heaps to withstand or undergo movement. The slope is an unprotected ground surface that can be situated at an angle of horizontal. Slopes are necessitated in the construction of railway embankments and highways, levees, bridges, earth dams, reservoirs and canals, etc., and are generally less expansive. Failures of natural and man-made slopes have demise …
Published in Journal of Geotechnical Engineering · Vol. 6, Issue 3, 2019 · pp. 41–46 Read article
-
Electricity Distribution and Consumption Analysis of Bhubaneswar Urban Complex using GIS Technology
Abstract: Power is a critical infrastructure for economic development of any part of the world. Management of power production and distribution is essential for holistic economic growth. For effective implementation of various developmental programmes for agricultural, industrial and urban infrastructure growth, adequate power supply is essential. Shortage of power supply is one of the major factors of low production and slow growth rate. Odisha government has taken drastic measures to improve …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 2, 2014 · pp. 12–21 Read article
-
Identification of Accident Hot Spots at Different Roads of Midnapore Municipality Area: A Geoinformatic Approach
Abstract: Road traffic injuries (RTIs) are a huge public health and development problem, killing almost 1.2 million people a year and injuring or disabling almost 20 to 50 million or more. Both WHO and World Bank data show that without appropriate action these injuries will rise dramatically by the year 2020, particularly in rapidly-motorizing countries. The study identifies the volatile traffic areas where road accidents are almost regular events and assess …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 1, 2014 · pp. 20–38 Read article
-
A Laboratory Methodological Proposal for “Geotechnical Lime Stabilization of A-4 Soils”
Abstract: This paper establish the beginning of a research process regarding the behavior of soils stabilized with lime. Generally, the geotechnical practice of soils stabilized with lime requires a first step conducted in the laboratory, to attest the features of “natural soils” in order to improve their behavior in term of geotechnical performance and, a second step, carried out onsite with experimental test fields, in order to verify the benefit obtained …
Published in Journal of Geotechnical Engineering · Vol. 8, Issue 1, 2021 · pp. 1–11 Read article
-
Evolutionary Dynamics of the East African Rift System: Implications for Hydrocarbon Exploration
Abstract: Rifts formation is a complex mechanism that has always generated debate with different models beingfronted, from thermal bulges to cratonic pull, all in an attempt to explain how the rifts form. East Africarift system (EARS), and its associated sedimentary basins within the general regional tectonicframework is one of the most active rifts in the world. The EARS has, over the years, experienced someoil and gas exploration though characteristically low. However, …
Published in Journal of Geotechnical Engineering · Vol. 10, Issue 3, 2023 · pp. 47–58 Read article
-
The Application of Ergonomics in the Work Environment of ICU
Abstract: Ergonomics plays an important role in healthcare sector. Healthcare as a work environment and as an industry presents a unique set of challenges and opportunities for applying ergonomics. Healthcare industry should make its objectives such that the work environment provided is safe, effective and comfortable. The objective of this work is to study the importance of ergonomics in intensive care nursing for safe and healthy work environment. Data was collected …
Published in Journal of Industrial Safety Engineering · Vol. 4, Issue 2, 2017 · pp. 27–33 Read article
-
Heavy Metal Analysis in Soil: A Case Study through the Noyyal River, Tirupur
Abstract: Noyyal River is a tributary of Cauvery River which rises from Vellingiri hills in Western Ghats, Tamilnadu South eastern India and drains in to Cauvery River. The river flows through four states, Coimbatore, Tirupur, Karur and Erode in western Tamilnadu. Till the river reaches Tirupur, the pollution concentration is considerably low. But in the Tirupur area the rate becomes substantially high due to the textile effluent discharge and sustains downstream …
Published in Journal of Industrial Safety Engineering · Vol. 1, Issue 1, 2014 · pp. 19–22 Read article
-
Chlorine Leakage from Control Valve in Charging Station Pipeline: A Case Study
Abstract: This paper describes accidental release of chlorine gas from control valve through a chlorine charging system in a green color pigment manufacturing chemical industry. The chlorine gas dispersed over the entire reactor floor and nearby area at night time shift work. This paper presents root cause analysis of the incident. Corrective and preventive measures are also discussed. Finally, conclusions reached with recommendations are drawn for industrial facilities for handling and …
Published in Journal of Industrial Safety Engineering · Vol. 1, Issue 2, 2014 · pp. 1–6 Read article
-
Machinability Studies of Chrome Steel in Turning Operation: An Experimental Investigation
Abstract: Studies on Machinability aspects are important from the standpoint of optimizing the parameters setting during the machining operations. This paper adds value to the knowledge base of machinability aspects. A report on the experimental investigation conducted, to study the effects of machining parameters on Surface Finish and Material Removal Rate (MRR) during the turning operation is presented. The current experimentation was carried out using two grades of chrome steel namely …
Published in Journal of Industrial Safety Engineering · Vol. 3, Issue 2, 2016 · pp. 10–18 Read article
-
Optimization of MRR and TWR on Electro Discharge Machining using Taguchi based GRA
Abstract: Electro Discharge Machining (EDM) is one of the most effective nonconventional machining processes in order to obtain better finishing quality result. It is vastly used to machine the most complex as well as intricate shapes so as the productivity increases in a very short time interval. The input parameters are; discharge current, voltage and pulse on time. Taguchi L9 orthogonal array is used to find out the Signal to Noise …
Published in Journal of Industrial Safety Engineering · Vol. 3, Issue 3, 2016 · pp. 26–32 Read article
-
A Review on Implementation of Lean Manufacturing in Maize Grinding Mill Assembly Line
Abstract: At present scenario, lean manufacturing has become a worldwide phenomenon. It is quite successful in drawing the attention of companies of all sizes. A large number of organizations are following the lean technologies and experiencing vast improvements in quality, production, customer service and profitability. Lean manufacturing is a systematic approach to identify and eliminate the waste through continuous improvement. The manufacturing industry in India must also look to leverage its …
Published in Journal of Industrial Safety Engineering · Vol. 3, Issue 1, 2016 · pp. 10–14 Read article
-
Design, Fabrication and Testing of Safety Valve Vent Silencer with Cyclone Separator for Industrial Applications
Abstract: The aim of this research work is to safeguard the infill materials, which is used inside the safety valve vent silencer. This research will help the infill materials from the wet steam and increases the life of the infill materials. The main parts of the research project are the cyclone chamber, center pipe. This cyclone separator drains the condensate through the lower part of the silencer and the steam releases …
Published in Journal of Industrial Safety Engineering · Vol. 8, Issue 1, 2021 · pp. 22–27 Read article
-
Evaluation and Analysis of Fire load in Storage Facility of Manufacturing Industry
Abstract: In recent years, industrial and residential fire is drawing more and more concerns. According to official government data, there have been numerous fire accidents in the industrial sector, leading to both casualties and significant property damage. Of particular concern are certain buildings in the pharmaceutical industry where large quantities of highly flammable and toxic substances are stored in confined spaces. This paper aims to examine the amount of flammable and …
Published in Journal of Industrial Safety Engineering · Vol. 10, Issue 2, 2023 · pp. 1–7 Read article
-
An In-depth Qualitative Exploration of Industrial Safety Factors Influencing Large-scale Construction Projects in India
Abstract: As the number of incidents at mega construction sites continues to rise, particularly in India, a developing nation, it is crucial to recognize the pivotal role the construction industry plays in contributing to the country’s economy. Nonetheless, this expansion has been concomitant with a concerning upsurge in accident and fatality rates within the construction industry. The aim of this study is to uncover the fundamental factors behind this trend which …
Published in Journal of Industrial Safety Engineering · Vol. 10, Issue 2, 2023 · pp. 33–41 Read article
-
An Approach for Discrete-Time Systems Design Using MPSM Continued Fraction Expansion Technique
Abstract: AbstractThis paper presents a new method for the design of the high-order discrete-time systems to overcome the limitations and drawbacks of some of the existing methods. It uses the Multi Point Squared-Magnitude Continued Fraction Expansion (MPSMCFE) and factorization technique for obtaining both denominator and numerator of the reduced order models. The method is extended for the design of high order systems using the reduced order model in place of original …
Published in Journal of Instrumentation Technology & Innovations · Vol. 7, Issue 3, 2017 · pp. 11–15 Read article
-
Design and Manufacturing of Human Operated Forklift for Small Scale Industry
Abstract: Mechanical forklift is a new and improved technique utilized in mechanical industry line. Forklift lift or handle more material and transfer one place to another place. Since of forklift it is possible that a one operator is adequate for material handling. When technology is enhanced advance forklift was established, they operate with the help of remotes it necessitates an electricity as well as a cost of remote-controlled forklift is high …
Published in Journal of Instrumentation Technology & Innovations · Vol. 10, Issue 3, 2020 · pp. 21–25 Read article