Search
88 articles for “Alloy steel”
-
Fractural Mechanics Crack Propagational Study on Different Material And Different Crack Location of weld joint in ANSYS
Abstract: AbstractThere have been spectacular failures made of ductile material. The structure as whole will remain as brittle only until the load is applied it will have elastic response it will not have plastic response. But near the crack tip there will have plastic zone and plastic zone indicates flow crack is going to behave for the present study analysis is carried out on crack near weld joint and three different …
Published in Journal of Structural Engineering and Management · Vol. 5, Issue 3, 2018 · pp. 29–33 Read article
-
A Brief Review on Interfaces of Copper Welded to Different Materials
Abstract: In engineering applications, three metals with high conductivity are primarily used such as copper (Cu), aluminium (Al), and silver (Ag). Each has its unique set of properties that affect specific engineering applications. Infact the choice of conductor depends on a mixture of cost, technical parameters, and environmental conditions. Among these, Copper is widely valued in engineering applications due to its antimicrobial property, excellent electrical (about 100% IACS) and thermal conductivity, …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 1, 2026 · pp. 23–36 Read article
-
STUDY ON THE FAILURES OF WELD JOINTS OF ROOF HOOPS & BIAS MEMBERS IN THE PROJECT JEWEL ROOF CONSTRUCTION AND APPLICATION OF FLUX-CORED ARC WELDING TO AVOID FAILURES
Abstract: During the construction of the roof structure of the commercial interconnection between the three airport terminals of the Changi Airport in Singapore, several failures have been noticed during the welding of roof hoops and bias members. In this context, experimental studies have been performed on transient heat transfer in welding distortion control by using flux-cored arc welding process (Self Shielded-SS) by using three(3)-dimensional welding in High Strength Low Alloy (HSLA) …
Published in Journal of Construction Engineering, Technology & Management · Vol. 9, Issue 2, 2019 · pp. 1–7 Read article
-
A Review on Metal Inert Gas Welding of Dissimilar Steels
Abstract: Joining of dissimilar metals has found its use extensively in power generation, electronic, nuclear reactors, petrochemical and chemical industries due to environmental concerns, energy saving, high performance, cost saving and so on. However efficient welding of dissimilar metals has posed a major challenge due to difference in thermal, mechanical and chemical properties of the materials to be joined under a common welding condition. This causes a steep gradient of the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 10, Issue 1, 2020 · pp. 1–15 Read article
-
Structural optimization of chassis frame of Electric Kart
Abstract: The chassis frame serves the function of giving structural safety to a vehicle at the same time incorporate different subsystems like steering and transmission. This makes the chassis frame a very crucial component especially in a vehicle like race kart. The weight of the chassis frame of an electric kart plays a major role in its performance and efficiency. By reducing the weight of a kart the range, maximum speed …
Published in Journal of Automobile Engineering and Applications · Vol. 5, Issue 1, 2018 · pp. 45–54 Read article
-
Prediction of Depth-Induced Stress Distribution and Maintenance Cost Implications for Submerged Structural Components
Abstract: This study investigates the influence of water depth on stress distribution and structural integrity of submerged mechanical components . Structural models fabricated from mild steel, stainless steel, carbon steel, and copper alloy were examined under hydrostatic loading corresponding to water depths between 30 cm and 150 cm. Results indicate that normal and shear stresses increased proportionally with depth due to intensified hydrostatic pressure. Mild steel exhibited the highest stress concentrations, …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 29–35 Read article
-
Influence of Mechanical Parameters on Corrosion Behavior of Metal Coupons in Simulated Environmental Conditions
Abstract: This study investigates the influence of mechanical parameters—namely applied stress, surface roughness, and deformation history—on the corrosion behavior of metal coupons exposed to corrosive environments. Mild steel and aluminum alloy specimens were prepared with controlled variations in tensile stress, polishing grades, and cold-working levels to simulate real-world mechanical influences. These coupons were immersed in a 3.5% NaCl solution under ambient conditions, and their corrosion rates were monitored over a 30-day …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 6–12 Read article
-
A Study on Friction Stir Processing Effected on Hardness and Tensile Properties When Single Pass and Double Pass Is Considered Using Al 6061 And Steel Material
Abstract: The principle of friction stir welding was initially employed to build the emerging technology known as friction stir processing, or FSP. FSP has shown to be a successful method of developing face mixes and increasing the material's mechanical parcels. Aluminum blends are among those accoutrements over which the FSP can be performed successfully. The study comprised the careful processing of steel and Al 6061 samples using both single and double …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 2, Issue 1, 2024 · pp. 16–23 Read article
-
Effect of Number of Sheets on the Performance of Bullet Proof Jackets
Abstract: In the present work effect of number of sheet for the same sheet thickness is conducted. Steel and aluminium alloy are used as a sheet material. The study is conducted using a finite element software ANSYS. Student version is used for the present work. Dimension of the sheet and bullet are taken from the literature. Parameter like velocity is also taken from the literature and value considered in the present …
Published in Journal of Production Research & Management · Vol. 8, Issue 2, 2018 · pp. 14–19 Read article
-
A Technical Review on the Wear Rate of Deep-Hole Drilling Process Based on BTA (Boring and Trepanning Association) Technique
Abstract: Deep-hole drilling of hard materials like carbon steel and super alloys like Inconel-718 is a very complicated process as the wear rate of BTA inserts is quite high as compared to other materials. In this review paper author aims to study the various factors affecting the wear rate and the type of wear occurring in different inserts used for deep-hole drilling of the above mentioned materials. It also emphasizes on …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 3, 2017 · pp. 18–23 Read article
-
Design and Analysis of Automobile Hood
Abstract: Bonnet is a main component of front portion of a car one which is used for many purposes. It is usedto decorate the car and add luxurious look. Bonnet is made in aerodynamic shape to reduce airresistance. Bonnet generally used to cover car engine. Therefore, the bonnet system is an accesspanel to the engine compartment to enable maintenance of power train, drive belts, battery, fluidlevels and lamp units, and it …
Published in Journal of Production Research & Management · Vol. 11, Issue 1, 2021 · pp. 42–52 Read article
-
Comparative studies of Oxidation and hot corrosion behaviors of uncoated and detonation gun sprayed Cr3C2-25NiCr coating on SA-213 boiler steel at 8000C
Abstract: Fe-based alloys suffer oxidation and hot corrosion when the surfaces were in contact with air (oxidation) as well as the salty atmosphere (Hot corrosion) at elevated temperatures. In these atmospheric conditions, non-protective oxide Fe2O3 was formed on the surface of alloys. Oxidation and hot corrosion have been recognized as a major problem in the applications of the diesel engine, boilers, gas turbines, and chemical power plant etc. Detonation-gun sprayed Cr3C2-25NiCr …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 1, 2019 · pp. 17–22 Read article
-
Weldability of Aluminum Alloy Using Pulsed current Tungsten Inert Gas Welding Process forMechanical Properties: A Review
Abstract: In the TIG welding, also known as gas tungsten arc welding, metal components are bonded by applying heat or pressure. Inert gas is used in pulsed current welding to encapsulate the electrodes and weld pools. Tungsten inert gas is used in the complex welding process known as TIG welding. It alternates between amps operating at high and low levels. Here, increasing the current results in improved power production and weld …
Published in Journal of Materials & Metallurgical Engineering · Vol. 14, Issue 1, 2024 · pp. 28–37 Read article
-
Effect of Welding Parameters on Microstructure and Mechanical Properties of Friction Stir Welded AA6061-T6 Joints
Abstract: Friction stir welding is a solid state joining process capable of joining similar and dissimilar materials, initially developed for joining of aluminium alloys. In the present work, the effect of friction stir welding parameters on the microstructure and mechanical properties of aluminium joints is studied. An attempt has been made to investigate the weldability of Al6061-T6 alloy using high speed steel tool in friction stir welding machine. Dye penetration test …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 1, 2019 · pp. 10–16 Read article
-
Comparative Environmental and Economic Assessment of Wind Turbine Blade Materials
Abstract: Wind energy has proven to be one of the most stable and non-polluting renewable energy sources to mass power production. For energy production wind turbine is an essential part of the wind power plant. The choice of the blade material and coating applied on it has a strong impact on aerodynamic performance, mechanical strength, fatigue life, manufacturing possibility, and environmental effects throughout the operating life of the turbine. Hence, authors …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 91–99 Read article
-
Optimization of Process Parameters of an Induction Furnace for Aluminium 6061 using Robust Design Approach
Abstract: Electric induction furnaces are extensively used in the foundry industries for the preparation of alloys and metal castings. The induction furnace works on the principal of electromagnetic induction. Some of the applications of induction heating include heat treatment, melting, surface treatment and in food industry. The detailed study about the working of an induction furnace was done. The induction furnace procured by mechanical department of our college is made by …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 1, 2017 · pp. 6–12 Read article
-
Electroplating and Corrosion Properties of Binary and Ternary Zinc Alloys with Nickel, Cobalt and Iron
Abstract: The anti-corrosive three binary (Zn-Ni, Zn-Co, Zn-Fe) and two ternary (Zn-Ni-Co, Zn-Co-Fe) alloy coating films on mild steel from acid chloride bath using sulphanilic acid and gelatin as additives for the electroplating technique. The normal Hull cell method was used to optimize the bath compositions, temperature and pH of the bath solutions for coating performance against corrosion. The cause of current density (CD) on metal weight percentage (M = Ni, …
Published in Journal of Thin Films, Coating Science Technology & Application Read article
-
Electroplating and Corrosion Properties of Binary and Ternary Zinc Alloys with Nickel, Cobalt and Iron
Abstract: The anti-corrosive three binary (Zn-Ni, Zn-Co, Zn-Fe) and two ternary (Zn-Ni-Co, Zn-Co-Fe) alloy coating films on mild steel from acid chloride bath using sulphanilic acid and gelatin as additives for the electroplating technique. The normal Hull cell method was used to optimize the bath compositions, temperature and pH of the bath solutions for coating performance against corrosion. The cause of current density (CD) on metal weight percentage (M = Ni, …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 8, Issue 3, 2021 · pp. 1–7 Read article
-
An Overview of New Coastal Research Vessel (N-CRV) Dry Dock and Construction
Abstract: A New Coastal Research Vessel (N-CRV) is a specialized ship designed for scientific research in fields like oceanography, geology, biology, and atmospheric studies, equipped with specific facilities and accommodations for sea missions. This paper discusses the coastal research ship dry-dock, construction, and design process, which involves three stages: concept, preliminary, and contract design. N-CRV must utilize scientific cruise, Exclusive Economic Zone (EEZ) survey, deployment, data collection, and seawater sample collection …
Published in Journal of Offshore Structure and Technology · Vol. 11, Issue 3, 2024 · pp. 1–11 Read article
-
Optimization of Turning Process Parameters by Genetic Algorithm Approach
Abstract: In this research, turning parameters were optimized through a genetic algorithm for the purpose to minimize surface roughness and to maximize the material removal rate. High finish quality is guaranteed through minimum surface roughness, and efficient process planning is facilitated through maximum material removal rate optimization. For predicting surface roughness and material removal rate with respect to spindle speed, feed rate, and depth of cut, the empirical models were developed …
Published in Journal of Production Research & Management · Vol. 15, Issue 1, 2025 · pp. 33–41 Read article