Search
551 articles for “steels”
-
Bond Behavior of Reinforced Concrete using Artificial Sand with Quarry Dust as Fine Aggregate
Abstract: Reinforced concrete (RC) is most widely used material in the construction industry. Normally natural sand is used as fine aggregate in the production of conventional concrete. Natural sand is obtained from the river bed through mining operation. To fulfill the requirement of construction industry excessive mining of sand from river bed has been carried out. It is causing threat to the natural environment. Hence, Indian government has led down restrictions …
Published in Journal of Geotechnical Engineering · Vol. 3, Issue 1, 2016 · pp. 44–50 Read article
-
Effect of Reinforcement on Bearing Capacity of Sand
Abstract: The reinforced earth concept, which is now being evaluated with increased significant encompasses formation of a composite of a soil with tension resistance reinforcing elements such as metallic and nonmetallic strips, bars, rods fibers or nets in the soil. The objective of using the reinforcement is to supress the normal tensile strains in the soil mass through frictional interaction. Flexible nature of reinforced earth mass enables it to withstand large …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 3, 2014 · pp. 8–12 Read article
-
An Experimental Studyon Behaviourof Piled Raft Foundation
Abstract: Piles in piled raft are often considered as settlement reducers, not load bearing members. Theexperimental study focuses on the behaviour of piled raft foundation subjected to vertical load. The model rafts were made of mild steel plateswith plan dimension 160 mm ×160 mm × 10 mm. The model piles used in this test were non-displacement piles of diameter 10 mm.Three lengths of piles were used in the experiment to represent …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 3, 2014 · pp. 26–34 Read article
-
Influence of wall friction on Active Earth Pressure in Model Test
Abstract: Earth pressure theories occupy a paramount position in the field of geotechnical engineering. The knowledge of active earth pressure under static condition is essential in designing a retaining wall as the damage to such retaining structures may lead to disastrous failure. A retaining wall helps in maintaining the ground surface at different elevations on either side of it. Without such a structure, the soil at higher elevation would tend to …
Published in Journal of Geotechnical Engineering · Vol. 8, Issue 1, 2021 · pp. 12–19 Read article
-
Effectiveness of Polyurethane Handle Grip Materials on Hand Arm Vibration while Operating Hand Grinding Machines
Abstract: The objective of this study is to evaluate the effectiveness of handle grips of polyurethane materials of different densities on hand arm vibration while operating hand held grinding machines. The hand arm vibration was analyzed in terms of fingertip force, using FingerTPS systems. Polyurethane foam handle grips of thickness 4 mm, of four densities were chosen for the study. Thirteen healthy male subjects consisting of students and professionals were involved …
Published in Journal of Industrial Safety Engineering · Vol. 4, Issue 1, 2017 · pp. 21–30 Read article
-
To Study About Forecasts of Low-Cost Housing in India
Abstract: The paper presents chip away requiring little to no effort and economical elective structure materials having preferences on regions, for example, India where cement or steel lodging is expensive. The undertaking tends to the difficulties and pigeonholes of utilizing these materials as a basic segment for minimal effort lodging and their equivalent volume for adjustment to the expansive range of elements—physical, biological, social, monetary and specialized—through various foodstuffs created which …
Published in Journal of Industrial Safety Engineering · Vol. 6, Issue 2, 2019 · pp. 14–20 Read article
-
Minimization of Effluent Produced by Electrical Industry
Abstract: There are two fundamental reasons of effluent viz. prevention pollution and thereby protecting the environmental and protecting the public health by safe guarding waste supplies and preventing the spread of water borne diseases. When untreated industrial waste water is discharge it will contaminate the natural water body i.e., river, lake with hazardous chemicals. It is absolutely necessary to study the characteristic of industrial waste water, to ensure its safe disposal. …
Published in Journal of Industrial Safety Engineering · Vol. 8, Issue 1, 2021 · pp. 15–21 Read article
-
Analysis of Vibrational Induced Structure Considering Rail and Seismic Load Using ETABS
Abstract: In the past, buildings next to railroad tracks were not taken into account when designing them, which resulted in catastrophic damage to the buildings as well as fatalities. For these structures to be designed safely, the vibrational loading must diminish. This study's case study is the Rani Kamlapati railway station in Bhopal, which was renovated by the Bansal Group and is the nation's first private railroad station. They suggested building …
Published in Journal of Industrial Safety Engineering · Vol. 10, Issue 3, 2023 · pp. 1–13 Read article
-
Nanostructured Cr-WS2 Solid Lubricant Coating for Space Applications
Abstract: Abstract Tungsten disulphide (WS2) is one of the widely used intrinsic low friction materials, which is commonly used in the form of coating. WS2 offers very low coefficient of friction only in non humid conditions. Presence of humidity destroys this property and restricts its utility. Modifying the structure of WS2 by adding certain metals helps in overcoming this limitation and in addition improves the mechanical properties. Further, deposition technique and …
Published in Journal of Instrumentation Technology & Innovations · Vol. 9, Issue 1, 2019 · pp. 12–18 Read article
-
A Review on Current Status of Biodegradable Surgical Implant Materials
Abstract: Since many years, inert metals such as stainless steel, cobalt-chromium and titanium alloys have been the primary biomaterials used for load bearing applications. In order to these metallic implants such as pins, screws and plates for repairing the defects have to be removed by secondary surgery once the bone tissue is healed, which will increase the morbidity, pain and cost. Hence conventional metallic biomaterials are biocompatible but not biodegradable. At …
Published in Journal of Instrumentation Technology & Innovations · Vol. 10, Issue 3, 2020 · pp. 5–15 Read article
-
Analysis of hyperloop transportation system using electromagnetism
Abstract: In this paper, we consider the feature of (Hyperloop technology) revolutionary transportation technology. The new technology of transportation, which travel in Vacuum fully.A high-speed train that promises travel at twice the speed of commercial aircraft transport. A Hyperloop transportation system would be “an elevated, reduced-pressure tube that contains pressurized capsule driven with in the tube by a number of linear electric motor’’. This system can achieve an average speed of …
Published in Journal of Instrumentation Technology & Innovations · Vol. 11, Issue 2, 2021 · pp. 1–6 Read article
-
A Technical Review on the Wear Rate of Deep-Hole Drilling Process Based on BTA (Boring and Trepanning Association) Technique
Abstract: Deep-hole drilling of hard materials like carbon steel and super alloys like Inconel-718 is a very complicated process as the wear rate of BTA inserts is quite high as compared to other materials. In this review paper author aims to study the various factors affecting the wear rate and the type of wear occurring in different inserts used for deep-hole drilling of the above mentioned materials. It also emphasizes on …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 3, 2017 · pp. 18–23 Read article
-
Optimization of Process Parameters in Wire EDM of HCHCrD2 using RSM-based Multi-objective Genetic Algorithm
Abstract: While precision is of paramount importance in machining of high strength conductive materials, Wire Electrical Discharge Machining (WEDM) is preferred. In the present work, experimental study has been carried to identify the appropriate process parameter settings for wire electrical discharge machining of high carbon high chromium D2 steel (HCHCrD2). The process parameters such as pulse peak current, pulse duration, pulse-off time, wire feed, wire tension and flushing pressure are considered. …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 6–10 Read article
-
Experimental Study on the Effect of Nose Radius for Multiple Responses in Turning of EN24 Using Grey Analysis
Abstract: The present work is to study the effect of turning process parameters on the multiple responses of material removal rate (MRR) and surface roughness (Ra). The experiments were carried out on EN24 a medium carbon steel which has a wide range of applications in the field of aircraft and automotive and mainly use in components such as gears, shafts, studs and bolts, connecting rods, propeller or gear shafts and aircraft …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 3, 2018 · pp. 10–16 Read article
-
Failure Analysis of Sheet Metal Utensils during Deep Drawing Process
Abstract: Sheet metal is one of the most important semi-finished products used in the steel industry, and sheet metal forming technology is therefore an important engineering discipline within the area of mechanical engineering. Deep drawing process is used for manufacturing the utensils from sheet metal. The sheet metal forming process to a large extent is based on experience, rules of thumb and trial-error experiments with or without use of scientifically based …
Published in Journal of Mechatronics and Automation · Vol. 3, Issue 3, 2016 · pp. 27–33 Read article
-
Surface roughness prediction in the turning operation by using experimental results and equation.
Abstract: This paper was discussed the values of surface roughness prediction models for turning EN24/817M40T steel (277 BHN) by using equation and experimental results. A factorial design technique has been used to study the effects of the main cutting parameters such as cutting speed, feed, and depth of cut, on surface roughness. The tests have been carried out using uncoated.A first-order prediction model within the speed range of 80-180 m min-1 …
Published in Journal of Materials & Metallurgical Engineering · Vol. 9, Issue 1, 2019 · pp. 27–30 Read article
-
Study of Shielded Gases for MIG Welding
Abstract: Protecting shielding gases are inert or semi-inert gasses that are regularly utilized in few welding forms, mostly in gas metal arc welding and gas tungsten arc welding (GMAW and GTAW, more prevalently known as MIG and TIG, respectively). Their purpose is to shield the weld region from oxygen, and water vapour. Contingent upon the materials being welded, these air gases can diminish the quality of the weld or make the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 1, 2016 · pp. 6–10 Read article
-
Parametric Optimization of MRR in Manual Air Plasma Arc Cutting of AISI 1017 MS using Design of Experiment
Abstract: In previous fifty years there has been remarkable research in machining and development in technology. Now a days with rise in competition in the market and to achieve high accuracy; the nonconventional machining has become more important in any industry. One of the most important unconventional machining processes is plasma arc cutting (PAC). Its high accuracy, finishing, ability of machining very hard materials makes it more demanding in the market. …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 2, 2015 · pp. 22–28 Read article
-
Plunger Technique: A New Approach to Stir Casting AMMC Preparation
Abstract: Metal matrix composites (MMCs) are materials that are highly attractive for large range of hi-tech engineering applications. Keeping this in mind, materials for the present investigation were prepared by a drastically modified stir-casting technique where the usual solid shaft stirrer was replaced by a hollow/tubular spindle-stirring mechanism through which silicon carbide particulates in small cylindrical capsule were introduced to the aluminum-magnesium alloy matrix with the help of a plunger rod …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 2, 2013 · pp. 26–32 Read article
-
Study on Electrolytic Smoothening Technique for AISI 316 LN
Abstract: Increasing applications of stainless steel in various fields where corrosion resistance is of prime importance, electrolytic polishing enhances the corrosion resistance of the component by decreasing the micro roughness. The current paper focuses on study of electrolytic smoothening technique for AISI316LN and the factors affecting the process as well. Factors which affect this process are composition of electrolytic bath, time, current–voltage relationship, temperature, stirring rate, etc. Detail analysis has been …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 2, 2013 · pp. 33–40 Read article