Search
33 articles for “wet process”
-
Development and Thermal-Soiling Performance Evaluation of Boron-Nitride Reinforced Polymer Nanocomposite Coatings for Solar Photovoltaic Applications
Abstract: Surface heating, dust buildup, and weakening triggered by ultraviolet (UV) light all have a vast effect on the long-term performance of solar photovoltaic (PV) modules. These issues all lower power conversion efficiency in real-world open-air circumstances. A nanocomposite coating built on fluoropolymer (FEP) that is reinforced with hexagonal boron nitride (h-BN) nanoparticles is invented by this study to enhance thermal dissipation, optical transmission, and resistance to dirt at the same …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 218–223 Read article
-
Synthesis of Novel Hybrid Biocomposites and Experimental Investigation of Mechanical Properties
Abstract: As industries increasingly adopt additive manufacturing, the demand for materials that offer better mechanical properties and functionality is on the rise. The purpose of present research work is to develop a novel hybrid biocomposites for 3D printing applications. The acacia bark, waste powder obtained from wet mahanarayan oil consisting of herbs and other bio filler was added in polylactic acid (PLA) for synthesis of hybrid biocomposites filament by twin screw …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 1–12 Read article
-
Elucidation of Physical Structural Stability of Nickel Nanoparticles Additive-Based Magnetorheological Grease
Abstract: This study investigates the influence of nickel nanoparticles on the physical properties and structural stability of magnetorheological grease (NMRG) as a smart composite. The incorporation of nickel nanoparticles aims to mitigate issues commonly observed in conventional magnetorheological grease (MRG), including particle aggregation within the fibrous matrix, limited material performance, and deformation instability. NMRG samples containing 1–5 wt% nickel nanoparticles were prepared using a mechanical stirring method. The tests focused on …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 191–215 Read article
-
Multi-Sensor System for Underwater Pothole Detection to Enhance Road Safety During Monsoon Seasons
Abstract: Monsoon seasons across India and similar tropical regions severely compromise road safety by causing water accumulation that conceals dangerous potholes beneath stagnant pools, leading to frequent vehicle damage, tire punctures, and fatal accidents. Traditional detection methods relying on smartphone accelerometers, ultrasonic sensors, or machine vision fail under flooded conditions due to acoustic signal reflection at water surfaces and optical distortions from glare and turbidity. This research proposes an innovative multi-sensor …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 4, Issue 1, 2026 · pp. 25–32 Read article
-
Optimizing Glass to Metal Composite Seal Performance: An integrated Approach with Artificial Neural Network, Multiple Regression, and Taguchi
Abstract: Composite materials, particularly glass to metal composites, are critical components in solar receiver tubes, where vacuum leakage can significantly compromise the efficiency of solar plants. This research addresses the technical barriers associated with the development of durable and high-quality glass to metal composite seals. We investigate the principles that can enhance the physical and chemical properties of these composite seals, focusing on the incorporation of TiO2 and MgO nanoparticles into …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 418–435 Read article
-
Land Degradation Mapping Using Integration of Remote Sensing and Geographic Information Systems in Maricá, Rio de Janeiro, Brazil
Abstract: The purpose of this paper is to study the growing problem of soil erosion in the municipality of Maricá, Rio de Janeiro, Brazil. The study area has an excellent agricultural condition. However, due to human and natural factors, water erosion is becoming a major problem. Therefore, new approaches are needed to determine soil degradation not only for the identification of hotspots, but also to identify areas prone to degradation to …
Published in Journal of Remote Sensing & GIS · Vol. 15, Issue 3, 2024 · pp. 45–56 Read article
-
Design and Assessment of Fixed Dose Combination Containing Fenofibrate and Pravastatin Sodium in Tablet Formulation: A Bioinformatics Approach
Abstract: The aim of this is study is to formulate and evaluate fixed dose combination of Fenofibrate and Pravastatin sodium in tablet dosage for the treatment of Dyslipidemia. For the formulation and optimization of fenofibrate layer, two factor three level factorial design was used as experimental design for optimization with a minimum of nine run. All the nine trial (F1–F9) has been formulated according to the experimental design by wet granulation …
Published in Research & Reviews: A Journal of Bioinformatics · Vol. 11, Issue 1, 2024 · pp. 1–20 Read article
-
Fungus Detection System
Abstract: This project identifies fungal pathogens in wet soil with sensors and gives an instant result through an Android app. It helps farmers avoid crop loss, increase yield, and encourage eco-friendly farming practices by enabling early detection and evidence-based decision-making for soil health management. Soil condition is most important to agriculture and environmental health. Having fungus in pre-maturity soil analysis can prevent crop damage and increase the yield. This project seeks …
Published in Journal of Microcontroller Engineering and Applications · Vol. 12, Issue 2, 2025 · pp. 30–34 Read article
-
A Ponder & Sedulousness Of Legion Shale Stabilizing Materials In Aqueous Based Drilling Fluid During The Process Of Borehole Strengthening
Abstract: Drilling fluid used while drilling the layers of shale will have the potential of reacting with water which tends to increase stickiness, induce swelling and promote sloughing of the borehole. This results in the reduction of drilling fluid circulation, increased mud loss, increase in torque and drag, reduction in lubricity. This will ultimately result in the increase of Non-Productive Time (NPT) during drilling which in turn increases Capital Expenditure (CAPEX) …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 35–40 Read article
-
Agro- residue Pretreatment Tools and Techniques: A Detailed review
Abstract: This review examines the significance of biomass pre-treatment in facilitating efficient biofuel production from lignocellulosic materials. Different methods of pre-treatment, such as acid, alkaline, liquid hot water, ionic liquids, organosolv, ozonolysis, wet oxidation, steam explosion, ammonia fiber explosion (AFEX), carbon dioxide explosion, and biological pretreatment, are examined in terms of their underlying principles, benefits, and drawbacks. Acid pretreatment effectively hydrolyzes hemicellulose but suffers from equipment corrosion and high operational costs, …
Published in Research & Reviews : Journal of Botany · Vol. 13, Issue 1, 2024 · pp. 22–31 Read article
-
Investigation of the independent and combined roles of Gr and ZrO₂ on strengthening behaviour of Al-7075 Composites
Abstract: This study investigates the effect of individual and hybrid reinforcements on the mechanical and microstructural behaviour of Al7075 composite fabricated using the 2-step stir-casting technique. Four compositions were made with the base Al-7075, Al-7075 3 weight % ZrO2, and Al-7075 3 weight % Gr as well as a hybrid composite Al7075 with 3 wt.% Gr, 3 wt.% ZrO2. 2-step stir-casting was used to increase the wettability of the particles, decrease …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1060–1075 Read article
-
Aluminum based types of hydrophobic coatings for Engineering Materials: A Review
Abstract: Today's coating applications allow for the employment of a wide range of techniques and substances to safeguard products and structures from chemical and chemical harm. Coatings are now widely utilized in manufacturing across the globe to boost productivity and cut costs, both of which are crucial for maintaining the industry's profitability. Materials with coatings are stronger than those without coatings. Strong and hard metals, ceramics, bioglass, polymers, and plastic materials …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 113–133 Read article
-
A Comparative Study of Oven, Spouted Bed, and Convective Tunnel Drying Methods of Mango for Oil Production
Abstract: Mango seeds, with a high moisture content exceeding 70% (wet basis) require effective drying methods to ensure their preservation and to enhance the quality of derivative products like mango seed oil. Proper drying is essential to inhibit enzymatic activity and microbial growth, which extends the shelf life of these seeds. This study investigates multiple drying techniques, including conventional oven drying, spouted bed drying, and convective tunnel drying, to determine their …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 16, Issue 1, 2025 · pp. 15–19 Read article