Search
28 articles for “Taguchi Methodology”
-
Influence of Alkali Treatment on the Tensile Properties of The Hybrid Fiber Reinforced Polymer Matrix Composite
Abstract: In this study, the effect of alkali treatment on the tensile strength of the hibiscus fiber, gongura fiber, and treated madar fiber-reinforced Polymer Matrix Composite (PMC) is studied. The Sodium Hydroxide (NaOH) solution is utilized for madar fiber treatment. The traditional hand layup methodology was used for fabrication. The influence of tensile property control variables such as duration of fiber treatment, concentration of NaOH for treatment, and proportion of fiber …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 28–34 Read article
-
Parametric Optimization of CNC Wire Cut EDM for Oil Harden Non-Shrinking Steel: A Comparative Study
Abstract: There has been a rapid growth in the development of harder and difficult to machine metals and newly developed alloys. Conventional machining methods are not suitable and uneconomical for such materials, thus development starts for newer concepts in metal machining. It thus plays a major role in the machining of dies, tools, etc., made of tungsten carbide, hard steel, alloys used in the aeronautics industry. It is a great concern …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 3, 2015 · pp. 44–58 Read article
-
Problem formulation for predicting optimum trans-esterification process parameters of biodiesel production and their performance analysis in diesel engine
Abstract: The various alternate fuels have been used in the past research to run the compression ignition engines. One of the fuel is the biodiesel which is used in the blended form with diesel. The emission parameters are reduced to 30-40% and the performance parameters are increased to some extent. This paper represents the various past research related to biodiesel based engines. The various steps in predicting the optimum process parameters …
Published in Journal of Automobile Engineering and Applications · Vol. 10, Issue 1, 2023 · pp. 41–44 Read article
-
Drip Irrigation Pipe Manufacturing Process and Defects in It- A Review
Abstract: In the development phase of drip pipe, conventional procedures for pipe extrusion line setup process were based on tryouts and then decisions to change the process parameters were made to minimize the errors occurring in pipe extrusion process of drip pipe. Every line setup needed the same methodology and hence loss of valuable time and material scrap. The variation of raw material supplies is also considered in this optimization process. …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 38–48 Read article
-
A review on Methodology used for Dry Turning of AISI 52100 Steel
Abstract: Bearing steel like AISI 52100 is one of the most widely used high cutting steel in industry for manufacturing of bearing. A large amount of coolant is used for machining at high speed due to which increase there has been a significant increase in environmental hazards. So Green or Dry manufacturing with optimize cutting parameters and its effect on tool material & work piece quality need to be studied to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 467–475 Read article
-
Wear and Tribological Characteristics of Novel Metal Matrix Composites
Abstract: The development of advanced metal matrix composites (MMCs) with enhanced tribological performance has become increasingly important due to the premature failure of critical engineering components operating under severe wear conditions in automotive, aerospace, marine, defense, and power generation systems. Conventional composites such as Copper–Alumina and Aluminium–Silicon Carbide have demonstrated improved mechanical and wear characteristics; however, their widespread application is often limited by issues including particle agglomeration, non-uniform reinforcement distribution, porosity …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1326–1346 Read article
-
Simulation and Experimental Studies on the Effect of Injection Moulding Parameters on Tensile Properties of ABS Thermoplastic Specimen
Abstract: AbstractThe injection moulding process is the most widely used method of manufacturing Engineering thermoplastics. Thermoplastic blends and composites are suitably replacing metals and ceramics in most circumstances. This trend is mainly due to the versatility and compatibility of the injection moulding process. However, the injection moulding conditions has a significant impact on the aesthetic and functional characteristics of the final product as the flow induces substantial variation in the properties …
Published in Journal of Polymer & Composites · Vol. 3, Issue 2, 2015 · pp. 1–10 Read article
-
Fabrication and Multi scale Characterization of Functionally Graded Composites Reinforced with Hybrid Ceramic–Metallic Phases
Abstract: Using composite materials as functionally graded composites (FGM) can improve its excellent material properties. In this work, magnesium peroxide, silicon carbide, and aluminum are used to create four-layer FGMs. The sintering process, which blends the particles of each material using a powder methodology, has been used to complete the fabrication process. Three factors, including sintering time, sintering temperature, and compacting pressure, are taken into account when fabricating FGM. The FGM …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 3, Issue 2, 2025 · pp. 1–11 Read article