Search
112 articles for “Dry drilling”
-
Parametric Study of Laser Drilling Process Using Multi Variable Regression Analysis
Abstract: The laser drilling process is an advanced manufacturing technique extensively employed for intricate and high-value components in aerospace, automotive, and electronics industries. Laser drilling technology offers opportunities to meet the contemporary demands of industries using a broad spectrum of engineering materials. However, this process encounters several engineering challenges such as thermal damage, dimensional inaccuracies, and the formation of a recast layer in the drilled components. This study focuses on examining …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1000–1015 Read article
-
Drilling Effect on Fiber Composites: A Review
Abstract: Composites laminates show immense mechanical properties like strength-to-weight ratio, damage tolerance, fatigue and corrosion resistance therefore conventional materials are replaced by composites in many areas such as automobile and aircraft structure. Machining of composites is very difficult than machining of a conventional material because composites are inhomogeneous and extremely abrasive. In production drilling is important machining process used to produce hole for riveted and bolted joint. There are many improvements …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 3, 2015 · pp. 42–50 Read article
-
The Influence of Fresh Raffia Palm Trunk on the Bioremediation of Oil-Based Drill
Abstract: This study determines the effect of fresh raffia palm for biodegradation of oil-based drill cuttings bioremediation. The experiment was conducted at the rivers institute of Agricultural research and training (RIART) located at the Rivers State University, Port Harcourt. Samples of oil-based drill cuttings were bulked in eleven reactors with four replications (T1, T2, T3-T11). The physiochemical properties of the initial drill cuttings were analyzed. Also, the physiochemical properties of the …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 41–48 Read article
-
Optimization of Process Parameters for AISI 304 Using Micro-EDM Drilling Process Through Response Surface Method
Abstract: The increasing demand for micro-parts in high-tech products, such as micro-electromechanical systems (MEMS) applications and micro-electronic devices, has driven significant advancements in micromachining technologies. Among the various micromachining processes, the fabrication of accurate microholes and pins is critical for the performance and reliability of miniature components. Micro-hole drilling plays a vital role by enabling the production of deep holes with excellent straightness, roundness, and surface quality. It is widely used …
Published in International Journal of Manufacturing and Production Engineering · Vol. 3, Issue 1, 2025 · pp. 37–47 Read article
-
A Technical Review on the Wear Rate of Deep-Hole Drilling Process Based on BTA (Boring and Trepanning Association) Technique
Abstract: Deep-hole drilling of hard materials like carbon steel and super alloys like Inconel-718 is a very complicated process as the wear rate of BTA inserts is quite high as compared to other materials. In this review paper author aims to study the various factors affecting the wear rate and the type of wear occurring in different inserts used for deep-hole drilling of the above mentioned materials. It also emphasizes on …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 3, 2017 · pp. 18–23 Read article
-
Drilling of Composite Materials: A Review
Abstract: In today’s world composites are replacing metals due to their superior properties such as light weight; low wear rate etc. Composites are widely used in automobile, aerospace and aircraft structural components. While drilling composite laminates, because of high hardness, they are difficult to machine, which results in low drilling efficiency and undesirable drilling induced delamination. The present paper is intended to focus on review of various works reported on drilling …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 2, 2015 · pp. 1–10 Read article
-
Review on Challenges in Drilling Non-metals
Abstract: Drilling is widely used in manufacturing industry and can be easily performed on all materials. It is well known that drilling produces under size of the hole and we need to carry out further operations like boring to get the exact dimensions. When coming to nonmetals like composites maintaining the dimenions in drilling operations is a critical task, as they are laminated with different materials and chances of defects present …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 2, 2023 · pp. 15–21 Read article
-
Optimization of Process Parameters for AISI 304 Using Micro-EDM Drilling Process: A Review
Abstract: Today, a variety of microparts are needed to fabricate high-tech items including MEMS applications and micro-electronic parts. The advancement of micromachining technology becomes ever more important in order to produce these micro parts. The creation of accurate holes and pins is one of themultiple processes in the micromachining process that is necessary for many small components. In order to create deeper, more straight holes, micro-hole drilling is utilized in a …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 3, 2023 · pp. 26–37 Read article
-
Condition Monitoring of Drilling Rigs
Abstract: This paper is interned to give improved maintenance of various equipment’s in a deep drilling rig used for drilling exploratory oil and gas wells. Since drilling rigs are capital intensive a need was felt to reduce their maintenance cost and increase their life expectancy. Thus the diagnostic technique like condition monitoring was implemented to diagnose the various problems in the machinery which are caused due to continuous usage. Condition monitoring …
Published in Journal of Petroleum Engineering & Technology · Vol. 7, Issue 3, 2017 · pp. 7–11 Read article
-
Flexural Strength and Drilling Parameter of Natural Fiber Composites with Usage of Epoxy Resin
Abstract: An attempt that has been made to take use of the advantages offered by natural composite materials in light of the fast advancement of research and development in this field over the course of the previous two decades, from the laboratory to the factory floor. During the manufacturing process of laminates, polymer matrices are used, while cotton, jute, and sisal are utilised as reinforcing materials. Epoxy resin is used to …
Published in Journal of Polymer & Composites · Vol. 11, Issue 4, 2023 · pp. 37–45 Read article
-
Intelligent Optimization of Drilling Parameters in Polymer Composites using Machine Learning and Metaheuristic Techniques
Abstract: The study tests different ways to use ML and metaheuristic algorithms to determine the best drilling parameters for polymer matrix composites. The research uses a composite matrix made from 55.25% vinyl ester, 44.0% Nickel–Phosphorous coated glass fiber and 0.75% Al₂O₃ nanowires which are tested for tensile strength (64.57 MPa), flexural strength (85.86 MPa) and impact strength (71.79 kJ/m²). By applying a Taguchi orthogonal array, it is observed that a slower …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1795–1810 Read article
-
Taguchi Analysis of the Thrust Force and Delamination in Drilling of Glass Fiber Reinforced Epoxy/Clay Nanocomposites
Abstract: AbstractComposites are replacing several materials due to their superior properties such as high strength to weight ratio, high stiffness to weight ratio, better impact characteristics, corrosion resistance and design flexibility. Drilling is often required to facilitate the assembly of the parts to get the final product. However, drilling induced damage affects the quality of the drilled components. The present investigation is an attempt to study the effect of the cutting …
Published in Journal of Polymer & Composites · Vol. 2, Issue 2, 2023 · pp. 14–23 Read article
-
Investigation on Torque and Thrust Forces in Radial Drilling of Copper Alloys
Abstract: As a part of research over improvement of machining process; cutting forces, metal removal rate (MRR) and surface finish on mechanical elements has become quite significant in the operational and aesthetical point of view. To enhance accuracy and precision by adopting energy saving techniques, manufacturing firms are adopting automated systems in order to achieve manufacturing excellence. In the present work, the effect of various process parameters like spindle speed, feed, …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 2, 2016 · pp. 6–19 Read article
-
Investigation of Local Weighting Materials as a Substitute To Barite In Drilling Mud Formulation
Abstract: Weighting materials are important components needed to increase the density of drilling mud in order to provide enough hydrostatic pressure to balance abnormalpore pressures. In Nigeria, millions of dollars are spent annually in importing barite to serve this purpose. However, there exists large reserves of weighting materials such as barite, hematite, dolomite, calcite, ilmenite in Nigeria hence the need to investigate the suitability of these materials as substitute for imported …
Published in Journal of Materials & Metallurgical Engineering · Vol. 10, Issue 1, 2020 · pp. 39–48 Read article
-
Experimental Investigation on Machining of AISI 1045 Stainless Steel by using Cryogenic Cooling of Micro EDM Drilling Process
Abstract: In this experimental work, the cryogenic cooling of the Micro-EDM (µEDM) drilling process for improving the performance and quality of micro holes. The controllable parameters such as the current (Ip), pulse on time (Ton), Pulse off time (Toff) and gap voltage (Vg) were chosen for further investigation. The Taguchi L27 orthogonal array is preferred to achieve the best experimental runs. Case hardened AISI 1045 stainless steel is selected to perform …
Published in Journal of Materials & Metallurgical Engineering · Vol. 10, Issue 2, 2020 · pp. 21–37 Read article
-
Designing Methodology for Identifying Different Types of Influx Entering in a Well Bore during Drilling and Study of Influx Behavior
Abstract: Drillers frequently encounter kick in drilling operations. Kick refers to the unwanted entry of formation fluid into the well bore. Primary well control and secondary well control are used to control influx entry into a well during drilling operations. Primary well control refers to making the overbalance by the hydrostatic pressure exerted by drilling fluid on the formation pressure. Secondary well control refers to controlling the kick through the use …
Published in Journal of Petroleum Engineering & Technology · Vol. 6, Issue 3, 2016 · pp. 7–11 Read article
-
Review of Radial Drilling Technology and Viable Prospect in Mature Field Development in the Niger Delta
Abstract: A review of some Niger Delta oil field reservoirs indicates that most of the reservoirs are at the mature stages, thereby vulnerable to challenges such as; coning due to reduced size of the oil column, low oil production and lack of access to the residual oil trapped between existing wells of the mature field. Due to coning occurrences in the Niger-Delta oil field, most wells have been shut-in and a …
Published in Journal of Petroleum Engineering & Technology · Vol. 5, Issue 2, 2015 · pp. 60–66 Read article
-
Study and Analysis of Body Postures Using Ergonomic Assessment Tools in Drilling Operations
Abstract: Ergonomics is one among the major factor that is curiously viewed by the modern world. Musculoskeletal disorder and awkward posture are the two dominant issues in ergonomics. The paper aims at studying and analyzing various musculoskeletal disorders, body postures, and other ergonomic aspects in vertical drilling operation in a laboratory work place using engineering students. Drilling is an operation in which ergonomic issues arise. Drilling is the most common operation …
Published in Journal of Industrial Safety Engineering · Vol. 2, Issue 1, 2015 · pp. 28–42 Read article
-
Synthesis and Experimental Evaluation of Graft Polymer Nanocomposite in Water Based Drilling Fluid System for Reactive Unconventional Reservoirs
Abstract: AbstractThis experimental work discusses the evaluation of polyacrylamide-grafted-gum arabic/carboxymethyl cellulose nanocomposite as a drilling mud additive for the drilling of reactive shale formations which may lead to wellbore instability. The synthesized nanocomposite was synthesized with free polymerization technique and it was characterized by XRD, FTIR, and FESEM. Then, it was preceded in the development of the WBDMS. Its effect on the rheological and filtration control properties of the formulated mud …
Published in Journal of Polymer & Composites · Vol. 5, Issue 2, 2017 · pp. 34–41 Read article
-
Experimental Analysis of the Effect of Fine Milled Husk of Rice as a Novel Filtration Control Agent for Water Based Drilling Fluid System
Abstract: Drilling operation is a complex process that requires integration of various engineering systems. As the drilling continues, the formation encountered offers challenges to wellbore integrity as pressure increases with depth. The influx of formation fluid is contained by the overbalance provided by weighted drilling fluid column. Another critical function of the mud is to restrict the filtration fluid lost to the formation by forming a suitable mud-cake around the wellbore. …
Published in Journal of Petroleum Engineering & Technology · Vol. 7, Issue 1, 2017 · pp. 4–8 Read article