Search
32 articles for “Compression molding”
-
Corn Husk Fiber–Reinforced PLA Biocomposites: Mechanical, Thermal, and Biodegradation Performance
Abstract: The increasing environmental burden caused by conventional petroleum-based plastics has driven significant interest in the development of sustainable polymer composites reinforced with renewable natural fibers. In the present work, corn husk fiber (CHF), an agricultural waste by-product, was utilized as a reinforcing phase in a polylactic acid (PLA) matrix to fabricate eco-friendly biocomposites. Composite samples with varying fiber loadings (0–40 wt.%) were produced through twin-screw melt blending followed by compression …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 312–327 Read article
-
Mechanical and Functional Performance of PET–Kenaf Fiber Hybrid Composites for Domestic Household Applications
Abstract: This research presents a hybrid composite of recycled polyethylene terephthalate (PET) and Kenaf fibers for sustainable household applications. Polyethylene terephthalate from consumer bottles was reinforced with Kenaf fibers at volume fractions of 10–30% and composites were created through compression molding. Mechanical characterization involved tensile, flexural, impact, and hardness testing where appropriate and was standardized according to ASTM standards, while their interfacial interactions were characterized by imaging through SEM. Linear and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1482–1498 Read article
-
Layered Metal–Polymer Hybrid Laminates with Embedded Impact Sensors for Connected Automotive Panels
Abstract: The increasing demand for lightweight, intelligent, and structurally reliable automotive components has accelerated the development of multifunctional hybrid materials capable of simultaneously providing superior mechanical performance and real-time structural health monitoring. In this study, a novel layered metal-polymer hybrid laminate incorporating an embedded flexible impact sensor was developed for connected automotive panel applications. The laminate was fabricated using AA6061-T6 aluminum alloy face sheets and a thermoplastic polyurethane interlayer through hot-press …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Assessing the Mechanical, Structural and Thermal Performance of Boehmeria Nivea and Agave Sisalana Fiber Reinforced Polymer Composite by using Seashell Powder as a Filler Material
Abstract: Natural fiber composites have replaced plastics and have been used to the maximum extent. Hybridization of natural fibers with filler materials has achieved higher tensile, impact, and flexural strength compared to single fiber composites. In this research, the mechanical properties were investigated with the ramie and sisal hybrid fiber reinforced with seashell powder as filler material. Filler material can enhance the flexural property of the natural fiber. Hybrid composite plates …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 355–369 Read article
-
Ultrasonic Dispersion of Halloysite Nanotubes for Enhanced Mechanical, Thermal, and Morphological Performance of Epoxy Composites
Abstract: Halloysite nanotube (HNT)-reinforced epoxy nanocomposites were prepared by mixing HNT with bisphenol-A epoxy (LY 556) using ultrasonication, followed by compression molding. HNT contents of 0–5 wt.% were used. The composites were evaluated for tensile strength, flexural strength, Shore D hardness, Izod impact strength, and thermal stability using thermogravimetric analysis (TGA). The fractured tensile surfaces were also examined to understand the failure mechanism and interaction between HNT and the epoxy matrix. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Enhanced Thermal Stability and Thermophysical Properties of High Density Polyethylene Based Polymer Composite Synthesized Through Compression Moulding Route
Abstract: Polymer composite materials attract researchers as polymers can be filled with different fillers to get desired properties. Thermophysical properties of HDPE-silicon composite is reported in the present study. HDPE-Si composite was synthesized by hot compression and molding technique for different silicon volumetric ratio. Thermal conductivity as well as thermal diffusivity was found to be enhanced significantly on increasing the filler volumetric ratio. Thermal conductivity value for 20 volume % composite …
Published in Journal of Polymer & Composites · Vol. 11, Issue 5, 2023 · pp. 1–16 Read article
-
Physico-Mechanical Behavior of Euphorbia Abysinica and Wood Chips Composite
Abstract: In this study, we prepared composite test specimens from Eucalyptus chip particles of sizes 0.5 mm, 1 mm, and 2 mm combined with Euphorbia-Abyssinica fluid at an 80:20 mass ratio. We produced the particleboard under a compression load of 150 KN and kept it in the compression machine for thirty minutes inside the mold. After removing it from the machine, we secured it with C-clamps for twenty-four hours. We covered …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Mechanical Behavioral Analysis of Sugarcane Bagasse, Coconut Fiber and Kevlar Fiber Reinforced Composite with Micrographs
Abstract: Asbestos and alloys are materials that are frequently used as brake pads; however, because these materials pose risks to human health and the environment, including lung cancer, it is necessary to replace the materials used in brake pads. In place of the current brake pads, composite fibers such as kevlar, sugarcane bagasse, and coconut are studied in this study. The procedure of manually laying up composite molding is used to …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 282–296 Read article
-
Rapid-On-Tongue Delivery: A Review of ODT Technologies, Taste Masking and Compliance
Abstract: Orodispersible Tablets (ODTs), another name for Fast Dissolving Drug Delivery Systems (FDDS), are innovative drugs that dissolve in the mouth rapidly without requiring water. These will be especially helpful for kids, the elderly, and others who have difficulty swallowing ordinary tablets or capsules. Superdisintegrants are used in these pills to break down quickly in the mouth, while flavorings or sweeteners are used to cover up any harsh or unpleasant taste. …
Published in Trends in Drug Delivery · Vol. 13, Issue 1, 2026 · pp. 01–08 Read article
-
Exploration of Mechanical Characteristics and Microstructural Analysis of Copper Matrix Composites with Hybrid Reinforcements via Muffle Furnace Sintering
Abstract: Metal Matrix Composites (MMCs) have drawn a lot of interest in the area of innovative materials because of how widely they may be used. Due to their extraordinary qualities, such as high thermal conductivity, higher temperature endurance, improved corrosion resistance, and great weldability, copper matrix composites stand out among them. These qualities make them desirable and promising materials for uses including heat exchangers, automotive parts, and electrical components. In this …
Published in Journal of Polymer & Composites · Vol. 11, Issue 12, 2023 · pp. 119–126 Read article
-
Composite Fabrication by Stir-Cast for Al C355.0 With Particulates Hematite Reinforcements at Different Weight Percentages in Copper Chills with and Without Water Circulation for Mechanical and Fatigue Performance
Abstract: This study investigates the fabrication of aluminum matrix composites using the stir casting method to analyze the mechanical characterization and fatigue behavior of Al C355.0 composites reinforced with varying weight percentages of hematite particulates. The hematite content was systematically adjusted from 0 wt. % to 12 wt. % in 3 wt. % increments, with the presence of constituent elements confirmed through Energy Dispersive Spectroscopy (EDS). The incorporation of hematite reinforcement …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 324–336 Read article
-
Experimental Investigation of Boron Carbide Reinforced Al-Mg-Si Alloy Nano Composites by the Stir Casting Method Using Machine Learning Algorithm
Abstract: For the purpose of this experiment, Al-Mg-Si alloys were manufactured with the use of the stir casting process with a metal mold. The alloys had different weight percentages of nano boron carbide, which ranged from 0 to 4% by weight. The intervals between the percentages were 0.5. Following that, the microstructural and mechanical parameters of the as-cast alloy and the nano composites were compared and contrasted according to ASTM Standards …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1766–1779 Read article