Search
227 articles for “Aluminum(Al)”
-
6000 inhibitors for aluminum and its alloys
Abstract: 6XXX series of aluminum alloys suffer from severe corrosion in acidic saline medium. These alloys are used for architectural, automobiles, aviation, household appliances, containers and electronic devices. Organic-inorganic sol-gel hybrid coatings are synthesized on these alloys. Rear earth inhibitors consider lanthanum inhibitors to be better than cerium inhibitors. These contexts discuss epoxy-silica-zirconia by sol-gel coatings, paddy residue, colchicines, rare earth coatings and ionic liquid for composites
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 2, 2019 · pp. 18–25 Read article
-
Twin Roll Casting of Aluminum Alloy AC7A
Abstract: Twin roll casting process is able to produce a strip from molten metal directly. Thus this process has a possibility to reduce total cost of sheet making comparing to conventional rolling process. Strip casting process has some disadvantages. Casting speed depends on the material properties. It is difficult to determine the casting conditions. Twin roll casting of aluminum alloy AC7A using commercial scale machine was operated. The aims of this …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 7, Issue 2, 2020 · pp. 30–36 Read article
-
Parametric Optimization of Aluminum Alloy 6061 Using Wire-EDM for Automotive Applications: A Taguchi-Based Approach
Abstract: Machining hard materials with complex geometries presents numerous challenges, often requiring the use of non-traditional methods such as wire Electric Discharge Machining (EDM). However, wire EDM machines operate at slow speeds, and increasing the speed can negatively impact surface finish, making it a difficult task. The ongoing research investigates the machinability study of Aluminum Alloy 6061 using wire EDM, emphasizing the optimization of process parameters to enhance machining performance and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 293–302 Read article
-
5000 Series of Aluminum and Its Alloys Opaque by Inhibitors
Abstract: 5XXX series of alloys are prepared for marine applications. Light weight, strength, low maintenance and inherent tendency to form passivity surfacing have selected these alloys for manufacture of cargo ships. Anti corrosive paints have been traditional protections in these alloys. Workers exposed to chromate residues during sanding of aircraft and recoating have increased risk of cancer to 250,000-fold higher. These paints are hazardous for aquatic life, so eco-friendly corrosion inhibitors …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 2, 2019 · pp. 1–8 Read article
-
Axial Compression Behavior of Aluminum (Al), Glass/Epoxy (GFRP) and Hybrid Al-GFRP Crash-box: An Experimental and Digital Image Correlation Approach
Abstract: The study aims to understand the axial compression characteristics and fracture of cylindrical Aluminum (Al), Glass/epoxy (GFRP) composite and Hybrid Al-GFRP crash-boxes. The hollow Al tubes are fabricated by rolling and bonding a thin aluminum sheet followed by rivet joints. The GFRP samples are manufactured using the wet-hand layup technique followed by the vacuum bagging method. Hybrid samples are manufactured by covering GFRP tubes with aluminum sheets on the outer …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 304–313 Read article
-
Fabrication and Evaluation of Aluminum Hybrid Metal Matrix Composite via Powder Metallurgy Approach
Abstract: The growing demand for lightweight materials in modern automotive industries has spurred the development of Aluminum-based metal matrix composites (AMMC). Utilizing the powder metal-lurgy method for fabrication offers a cost-effective alternative to other methods. Composites of Al6061 with varying compositions of 6–18 wt% SiC (8 microns) and 6–18 wt% B4C (10 mi-crons) were prepared to assess their physical and mechanical properties. Scanning Electron Mi-croscope analysis revealed uniform dispersion of SiC …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 205–211 Read article
-
Experimental Investigation of Aluminum Alloy 8010 by Friction Stir Welding
Abstract: A solid state welding method called friction stir welding (FSW) is used to fuse metals and alloys that are challenging to fuse using traditional fusion welding. The effects of tool pin and shoulder diameter on joining the aluminum alloy Al 8010 were examined in this study. The basis material for combining single butt-welded joints is a plate with a thickness of 6 mm. The welding was carried out on the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 14, Issue 3, 2024 · pp. 14–19 Read article
-
An Experimental Investigation of Process Parameters for Aluminum Alloy Composites
Abstract: The objectives of this work are to develop an aluminum alloy composites and investigate machining process parameters effect on the tool wear rate for composites. The composite is enhanced using silicon carbide and graphite. The composite is made by a method called stir casting. Furthermore, it is investigated both mathematically and experimentally. This study takes trial on aluminum alloy composite to see output characteristics tool wear rate are affected by …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 185–193 Read article
-
Multi-Layer Aluminum–Polymer Hybrid Structures for Improved Automotive Impact Performance
Abstract: Layered metal–polymer hybrid laminates have emerged as promising candidates for lightweight automotive structures requiring high impact resistance and structural reliability. In this study, aluminum/glass–epoxy hybrid laminates were fabricated using a symmetric stacking sequence through hot compression molding to evaluate their mechanical and energy absorption performance. Density analysis revealed an average measured density of 2.34 g/cm³, closely matching the theoretical value of 2.36 g/cm³, with a deviation of approximately 1.02%, indicating …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 42–53 Read article
-
H2 Production by Methanol Steam Reforming over Copper Impregnated Anodized Aluminum Oxide (AAO)
Abstract: Hydrogen production by methanol steam reforming (MSR) is easy and simple as compared to other reforming methods using fossil fuels such as methane steam reforming. The catalysts for MSR are well developed and available commercially. When constructing a small or micro reformer, the catalyst often needs to be coated on the wall of the metal substrate. In this case, the bonding between the metal surface and the catalyst layer must …
Published in Journal of Catalyst & Catalysis · Vol. 1, Issue 1, 2014 · pp. 23–28 Read article
-
Studies on Erosion Wear Behavior of Aluminum-3 Magnesium-10 Silicon Carbide Composite
Abstract: Aluminum-based metal matrix composites (MMCs) offer potential for advanced structural applications when high specific strength and modulus as well as good elevated temperature resistance along with light weight are important. In the present work, aluminum alloy-silicon carbide composite (Al-3Mg-10SiC) is developed using the stir-casting technique and is subjected to study the wear behavior. Solid particle erosion on Al-3Mg-10SiC was conducted. Implementation of design of experiments (through Taguchi and statistical techniques) …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 3, 2013 · pp. 39–50 Read article
-
STUDIES ON WEAR BEHAVIOR OF BORON CARBIDE PARTICULATES REINFORCED ALUMINUM 7075 METAL MATRIX COMPOSITES
Abstract: In this present work, Aluminum 7075 is used as matrix material with Boron Carbide asreinforcement. Two different compositions were used to prepare the composite. The composites werefabricated by Stir Casting Technique as per ASTM G99 and tested under Pin-on-Disc wear test rig. Theexperiments are conducted through conventional method and macro structural studies were carried out bySEM analysis. The results show that, in conventional method, the reinforced composite Aluminum 7075-10%B 4 …
Published in Journal of Polymer & Composites · Vol. 7, Issue 2, 2019 · pp. 1–7 Read article
-
Electrically Conductive Micro-Aluminum Reinforced Polymer Composites for IoT-Enabled Lightweight Antenna Housings
Abstract: Electrically conductive polymer composites have emerged as promising multifunctional materials for lightweight antenna housings by integrating structural strength, electrical conductivity, thermal stability, and electromagnetic interference shielding. In this study, micro-aluminum reinforced Acrylonitrile Butadiene Styrene (ABS) polymer composites were fabricated using twin-screw melt compounding followed by compression molding for IoT-enabled lightweight antenna housing applications. The influence of micro-aluminum loading on microstructure, mechanical performance, electrical conductivity, EMI shielding, thermal stability, and wireless …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Experimental Analysis and Optimization of Pulse TIG Welding Parameters for Dissimilar Aluminum Alloys
Abstract: Tungsten inert gas (TIG) welding is highly regarded as the primary welding method, especially for challenging metals like aluminum. Pulsed-current TIG welding has been specifically developed for welding aluminum alloys. Composite weld joints of aluminum alloys AA5052 and AA6063 find extensive use in diverse sectors such as automotive and marine applications, where significant mechanical properties and corrosion resistance are required. It is crucial to carefully select the process parameters to …
Published in Journal of Materials & Metallurgical Engineering · Vol. 16, Issue 2, 2026 · pp. 01–12 Read article
-
Characterization of Strength of Aluminum (Al 6063-T6) After Corrosion
Abstract: Aluminum are frequently used as light weight structure in various nautical design. One of them is the ship structure design where sever environment of saline water influences the damage of the structure and one among them is pitting. In this paper, an experimental verification of strength and impact of corrosion effect on Al-6063–T6 aluminum was presented. The specimens were exposed to saline water for various duration like 500 hrs, 750 …
Published in Journal of Experimental & Applied Mechanics Read article
-
An Experimental Investigation of Machining Parameters on Aluminum Composites
Abstract: The need for a material with good mechanical, thermal, and wear resistant properties is satisfied by aluminum composite. However, the biggest obstacle to substituting it with alternative materials is the machining challenges. For this kind of hard-to-cut material, electric discharge machining is a very efficient method. Thus, using a Taguchi-based method, an attempt has been made to determine the most advantageous amount of input parameters for EDM of Al composite. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 8–13 Read article
-
Investigating The Synergistic Effects of Micro and Nano Particle Reinforcements in Powder Metallurgy-Processed Aluminum Metal Matrix Composites for Enhanced Mechanical Performance
Abstract: The ever-growing demands of modern mechanical applications necessitate the development of materials with superior mechanical properties. In this research, we delve into the creation and evaluation of Aluminum Metal Matrix Composites (Al MMCs) made via the powder metallurgy route, reinforced with both micro and Nano-scale particles. The key aim is to investigate the possible cooperative effects of this dual reinforcement approach on the mechanical behavior of the composite. Traditional aluminum …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 220–229 Read article
-
High-Performance Aluminum Matrix Composites Reinforced with Graphene Nanoplatelets a Study on Mechanical and Thermal Behaviour
Abstract: This study investigates the effect of graphene nanoplatelets (GNPs) on the mechanical and thermal properties of aluminum matrix composites (AMCs) fabricated using the powder metallurgy route. Aluminum alloy Al-6061 powder was reinforced with varying GNP concentrations (0, 0.5, 1, 2, and 3 wt%), followed by uniaxial compaction and sintering. The influence of GNP content on the composite’s structural integrity, strength, and thermal behavior was thoroughly evaluated through tensile testing, hardness …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 38–49 Read article
-
Experimental, Analytical and Numerical Study of Energy Absorption Properties of Aluminum Crush Boxes with and without Buckling Initiators (Axial Loading)
Abstract: The crashworthiness in automobile is stated as the capability of a passenger car and its interior arrangements to safe-guard occupants from harm. Whenever an accident occurs, the passengers in the car can be injured due to one of the following reasons: (1) excess acceleration force; (2) physical injury from contact with injurious surfaces, and; (3) exposed to fire, smoke, and chemicals released during accidents. Thus effective crashworthiness design must take …
Published in Journal of Automobile Engineering and Applications · Vol. 4, Issue 2, 2017 · pp. 1–9 Read article
-
CHARACTERIZATION OF STRENGTH OF ALUMINUM (Al 6063-T6) AFTER CORROSION
Abstract: Aluminum are frequently used as light weight structure in various nautical design. One of them is the ship structure design where sever environment of saline water influences the damage of the structure and one among them is pitting. In this paper, an experimental verification of strength and impact of corrosion effect on Al-6063 – T6 aluminum was presented. The specimens were exposed to saline water for various duration like 500hrs, …
Published in Journal of Experimental & Applied Mechanics · Vol. 12, Issue 3, 2021 · pp. 48–61 Read article