Search
450 articles for “optimum”
-
Study on Effect of Insulation Design on Thermal-Hydraulic Analysis: An Important Aspect in Subsea Pipeline Designing
Abstract: The most imperative and challenging operational hazards for oil and gas pipelines are the risks associated with the transportation of fluids. When water, oil and gas flow simultaneously inside the pipeline, there are quite high chances that, water and hydrocarbon fluids can form and deposit hydrate such as wax and asphaltene on the inner surfaces of the pipeline and gradually blocking it. In this paper we explore and compare the …
Published in Journal of Petroleum Engineering & Technology · Vol. 4, Issue 1, 2014 · pp. 33–44 Read article
-
Improved Prediction of Fluid Contacts using Calibrated Material Balance Models
Abstract: The demand for oil has been on the high in the recent past and will continue as search for sustainable alternative energy sources intensifies. The exploration and exploitation of oil from subsurface reservoirs have posed several environmental challenges which include flaring and improper water disposal to name a few, caused by excessive production of gas and water. Hence, it is important to establish a reservoir performance monitoring scheme that will …
Published in Journal of Petroleum Engineering & Technology · Vol. 4, Issue 2, 2014 · pp. 25–36 Read article
-
A Model Approach of Controlling Coning in Oil Rim Reservoirs
Abstract: Water and gas coning in oil rim reservoirs poses serious hindrance to optimizing oil production in the thin oil beds as unwanted fluids tend to replace oil in the production stream. This invariably limits the ultimate oil recovery. In this study, semi-analytical models of estimating critical rate and optimum horizontal well placement were developed to control coning tendencies in oil rim reservoirs. The models were developed through semi-analytical analysis of …
Published in Journal of Petroleum Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 1–10 Read article
-
Estimation of Dulling Rate and Bit Tooth Wear Using Drilling Parameters and Rock Abrasiveness
Abstract: Optimisation of the drilling operations is becoming increasingly important as it can significantly reduce the oil well development cost. One of the major objectives in oil well drilling is to increase the penetration rate by selecting the optimum drilling bit based on offset wells data, and adjust the drilling factors to keep the bit in good condition during the operation. At the same time it is important to predict the …
Published in Journal of Petroleum Engineering & Technology · Vol. 9, Issue 3, 2019 · pp. 1–20 Read article
-
Production and Characterization of Essential oil using the Solvent Extraction Method from Brassica nigra seeds
Abstract: The purpose of this study is the Production, Optimization and Characterization of oil from Brassica nigra seeds using the Solvent Extraction Method. The result shows no difference from the seed oil extract from the mustard plants which grows in other parts of the world. This is to create awareness to utilize the Brassica nigra seed locally grown, as a potential source of edible oil for health benefit, such as additives …
Published in Journal of Petroleum Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 5–20 Read article
-
Integrated Rock Typing and Rock Mechanics Studies for Median Line Principle Optimization
Abstract: Once a field has been identified, and a general method of reservoir exploitation decided, there are several methods to achieve the reservoir management goal, but some ways may cost twice as much as others. The most critical operations to developing a field are drilling of wells, and it overemphasizes which in the early stages of field development. Petroleum wells have changed character in recent decades, as compared to earlier times. …
Published in Journal of Petroleum Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 21–32 Read article
-
Theoretical and Simulation Studies on Gas Well Performance
Abstract: The productivity of any oil or gas well is governed by its maximum flow potential with the available varying parameters such as draw-down pressure availability, tubing sizes available to lift the fluid, and others. The present study on the performance of a gas well delineates the appropriate parameters that are necessary for maximizing the flow from the reservoir to the wellhead surface by utilizing a performance simulator, with nodal analysis …
Published in Journal of Petroleum Engineering & Technology · Vol. 11, Issue 2, 2021 · pp. 9–24 Read article
-
Design of Ducts: An Industrial Perspective
Abstract: Central Air Conditioners working is a complex and cumbersome topic which takes a lot of time and effort. It’s a difficult task to explain the entire parts, its working and maintenance. Here an effort is made to explain about the designing of Ducts used in a central A/C. A Commercial building is taken for reference and each floor’s Duct designing is explained. The ground floor is designed with supply air …
Published in Journal of Production Research & Management · Vol. 10, Issue 1, 2020 · pp. 18–24 Read article
-
Parallel Conwip for a High-mix Multi-stage Production System with the entrance of rework
Abstract: In a complex production environment, more than one type of pull systems is often used to regulate the processesof different products. In literature, performance studies appertaining to multiple pull systems co-existed in aproduction environment are rare. The present paper evaluates the performances of parallel CONWIP (PC)systems in a high-mix production system with the entrance of rework. The production comprises three stages ofshared-machine facilities. Reject parts produced by the first stage …
Published in Journal of Production Research & Management · Vol. 1, Issue 1-2-3, 2011 · pp. 21–44 Read article
-
Photochemical Studies of Photosensitive Compound in DSS Cell
Abstract: Solar energy is our earth’s primary source of renewable energy. It is one of the most resourceful sources of energy for the future. A technique for converting solar energy into electrical energy via formation of energy rich species that exhibit the photo-solar effect is known as DSS cell. Therefore, the present study of DSS cell of Carbol Fuchsin (PC) with efficiency enhancer chemicals such as TEA reductant in alkaline media …
Published in Journal of Semiconductor Devices and Circuits · Vol. 4, Issue 3, 2017 · pp. 21–29 Read article
-
Simulation Study of Process Variations in Double Gate Junctionless Field-Effect Transistors
Abstract: This work discusses the process variations in symmetrical double-gate (DG) junctionless (JL) field-effect transistors (FETs) by device simulation. Output I-V characteristics along with subthreshold slope increase, DIBL variations with drain voltage and threshold voltage shift variations are systematically analyzed with the general variability issues including oxide thickness, channel thickness and doping concentration. Potential distribution in the body channel region is also analyzed. Optimum values of the variability factors are considered …
Published in Journal of Semiconductor Devices and Circuits · Vol. 2, Issue 2, 2015 · pp. 18–27 Read article
-
Design of Modified North Light Roof Trusses: Comparative Study
Abstract: The study of north light truss and modified trusses by analyzing and designing has been carried out and submitted the comparative study of the same in the form of tables, graphs and charts, which highlights the forces, deflections, optimum steel requires, actual steel requires as per grouping. STAAD.Pro V8i software also used to analysis and design of such models. Solar panel loads also considered on the truss. Limit State Method …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 2, 2020 · pp. 27–35 Read article
-
Octagrid an Alternative Lateral Load Resisting System
Abstract: The cost of the land in the rapidly developing urban cities have skyrocketed in the last few decades. Acquiring a piece of land has become very difficult for the builders and developers for different amenities and hence the concept of tall buildings has spread its roots in the urban infrastructure scenario. Tall buildings facilitate the optimum use of land and many amenities such as offices, residential apartments, shopping malls and …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 3, 2020 · pp. 29–33 Read article
-
Comparison of RCC and Steel Composite Structure subjected to Static and Dynamic Loads
Abstract: Steel has long been used for the construction projects but the use was limited to a certain height because of the buckling and bending becomes critical after a particular height.The RCC structure after extensive use and research proved to be much more economical and concrete as a construction material covered the whole urban jungle as we witness today. The hustle for the betterment of the construction industry particularly to provide …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 3, 2020 · pp. 1–4 Read article
-
Partial Replacement of Sand with Waste PET in Concrete
Abstract: Plastic solid waste generation increases per annum with the present current consumption habit prevalent within the society nowadays. The improper disposal of plastic has been a serious concern to the environment because it isn't easily degradable. the difficulty of environmental pollution caused By Polyethelene Terephthalates (PET) has been extensively discussed and therefore the best solution proposed is recycling. Therefore, one among the potential means to the matter is to recycle …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 3, 2020 · pp. 24–28 Read article
-
Steel Ductile Detailing of Moment Resisting Frames for Pre-engineered Buildings
Abstract: Long span structures with no interrupting column are necessary in any type of industrial structures and pre-engineered buildings (PEB) satisfies this need along with less time and cost as compared to conventional structures. This methodology is adaptable not only due to its quality pre-designing and prefabrication, but also due to its light weight and economical construction. The concept includes the technique of providing the best possible section according to the …
Published in Journal of Structural Engineering and Management · Vol. 3, Issue 1, 2016 · pp. 36–44 Read article
-
Evaluation of Mechanical Properties of Hybrid Fibers in Concrete
Abstract: Engineering Cementitious Composites (ECC) is an advanced growing method to increase the longevity of the structure in all behaviour aspects. ECC consist of cement, fine aggregate, fiber and water.High performance, ductility and durability of cementitious matrix can be achieved by addition of fiber. Nowadays, the member of fibers play a vital role to increase the overall structural behaviour of concrete matrix. In that, synthetic-based fibers are used in various applications. …
Published in Journal of Structural Engineering and Management · Vol. 2, Issue 1, 2015 · pp. 1–5 Read article
-
Strength and Durability Characteristics of Fiber Modified Asphaltic Bitumen
Abstract: Flexible pavements with bituminous surfacing are widely used in India. Exponential increase in traffic, overloading of commercial vehicles and significant variations in daily and seasonal temperatures have shown some limitations of conventional bitumen performance. Earlydevelopments of distress symptoms like cracking, rutting, raveling, undulations, shoving and potholing of bituminous surfacing have been reported for flexible pavements. Toenhance the properties of road, bitumen is modified by the addition of some waste materials. …
Published in Journal of Structural Engineering and Management · Vol. 2, Issue 1, 2015 · pp. 13–17 Read article
-
Development of Controlled Concrete by using Hypo Sludge
Abstract: Over 300 million tones of industrial wastes are being produced per annum by chemical and agricultural process in India. These materials pose problems of disposal and health hazards.The wastes like phosphogypsum, fluorogypsum and red mud contain obnoxious impurities which adversely affect the strength and other properties of building materials based on them. Out of several wastes being produced at present, the use of phosphogypsum, flurogypsum, lime sludge, hypo sludge, red …
Published in Journal of Structural Engineering and Management · Vol. 1, Issue 1, 2014 · pp. 16–21 Read article
-
Improving Quality of Thin Walled Sand Casting through Selective Quality Improvement Methods
Abstract: Six sigma is a quality improvement methodology. In this research paper, six sigma methodology is used for end shield FG 200 Grey casting of electric body. DEMAIC methodology along with Taguchi method is used to minimize the defect in end shield casting. DOE and analysis for variance techniques are used to determine the correlation of defects with the pouring temperature, pouring time and Si percentage and their optimum values are …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 2, 2017 · pp. 28–36 Read article