Search
1893 articles for “experiments” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
Experimental Investigation on Ferrocement Slab Using Steel Fibres and Different Sands
Abstract: Ferrocement is defined as wire mesh reinforcement impregnated with mortar to produce elements of small thickness. An experimental study has been carried out to study the effect of different compositions of cement mortar using 10% fly ash and different percentage of 6–8% silica fumes with two types of sands such as Badarpur sand and river sand and show the effect of load versus deflection curve and flexural strength of ferrocement …
Published in Journal of Structural Engineering and Management · Vol. 4, Issue 2, 2017 · pp. 27–30 Read article
-
Experimental Investigation on Mechanical Properties of Concrete Replacing of Steel Slag as Coarse Aggregate
Abstract: The basic objective of this study was to identify alternative source of good quality aggregate which is depleting very fast due to the fast pace of construction activities. This paper describes the optimum level of replacement of Energy Optimized Furnace (EOF) steel slag by weight of coarse aggregate for a mix proportion of M20 grade concrete to find out the optimum ratio of steel slag. Civil Engineers have been challenged …
Published in Journal of Structural Engineering and Management · Vol. 4, Issue 2, 2017 · pp. 44–49 Read article
-
Experimental Investigations of Prestressed Hollow Core Slabs and Grouted Hollow Core Slabs
Abstract: With the advent and rapid inclusion of prefabricated concrete system to the construction industry, it poses interesting research challenges to the academic world. The acceptance of hollow-core slab as an alternative to the normal reinforced concrete solid slabs is getting delayed due to the delusion among public. The usage of grouted hollow core slabs by filling the core with grout is one of the increasing demands observed by the hollow …
Published in Journal of Structural Engineering and Management · Vol. 3, Issue 3, 2016 · pp. 16–21 Read article
-
An Experimental Study on Effect of Seawater on Strength of M30 Grade Concrete
Abstract: The concrete structures constructed near the coastal areas may deteriorate due to the action of sea salts present in seawater on hardened concrete surface with passage of time. The strength decreases due to the formation of complex ions when chloride and sulphate ions, react with cement hydration products. In this study, experiments were carried out to get the effect of seawater on the strength of M30 grade concrete in laboratory …
Published in Journal of Structural Engineering and Management · Vol. 3, Issue 3, 2016 · pp. 55–59 Read article
-
An Experimental study on Strength parameters of OPC, PPC and Geopolymer Mortars
Abstract: Geopolymer mortar is a new trend in mortars, manufactured with fine aggregate and geopolymers like fly ash and silica fume, which gets activated by alkaline solutions like sodium silicate solutions. Research work on geopolymer based mortars is attaining more scope in present era because of its sustainable properties and easy availability. The study, includes to evaluate the strength in compression and bond strengths of different mortars in different curing methods, …
Published in Journal of Structural Engineering and Management · Vol. 9, Issue 3, 2022 · pp. 21–27 Read article
-
Experimental Analysis of a Portable Solar Water Distillation System
Abstract: We know that water available in National Capital Region of Delhi India is contaminated and have high hardness, so it cannot be used directly for industrial purpose. So I have made an attempt to get the distilled water of lower hardness with the help of solar energy. Experimental result of a double slope single basin solar distiller is explained in this paper. The motivation for this project is the conversion …
Published in Journal of Water Resource Engineering and Management · Vol. 2, Issue 3, 2015 · pp. 1–9 Read article
-
Validating the Gravity Recovery and Climate Experiment (GRACE) terrestrial water storage dataset using Terra MODIS NDVI anomaly.
Abstract: The Gravity Recovery and Climate Experiment (GRACE) is the advance tool for mapping the changes in the gravitation field of the earth. The satellite launches in 2002 and the follow off mission is in 2016. The gravitational changes of the earth are downscaled into the changes in the mass with the different algorithm by three institutions. Further the mass anomaly is converted into the equivalent water thickness of the terrestrial …
Published in Journal of Water Resource Engineering and Management · Vol. 9, Issue 1, 2022 · pp. 19–28 Read article
-
Experimental Investigation on Concrete with Replacement of Fine Aggregate from Scrap Tyre Rubber Dust
Abstract: Concrete is the most widely used construction material in the world in which cement and aggregates are the main constituents. This has led to continuous and increasing demands of natural materials used in the construction. Present study aims to explore the potential utilization of scrap tyre rubber in various Portland cement concrete categories for the production to study the structural behaviour of concrete, and to help partially solving environmental problem …
Published in Recent Trends in Civil Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 5–9 Read article
-
Experimental Study on Properties of Concrete with Phoenix Fibres
Abstract: In this paper, an attempt has been made to investigate the possibility of using phoenix fibre to improve the properties of concrete. The aim of this research is to investigate the properties of concrete with phoenix fibres of various percentages. Mechanical properties such as compressive strength, split tensile strength of concrete using phoenix fibre have been investigated. M20 grade of concrete has been used for this investigation. Mechanical strength tests …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 3, 2016 · pp. 40–45 Read article
-
Experimental Investigation on the Effect of Manufactured Sand in Concrete
Abstract: Concrete is the most widely used construction material owing to its versatile nature. Three fourth of the concrete is made of aggregates, amongst which fine aggregate has massive demand. River sand is the predominantly used fine aggregate, which is under significance because of the increased demand and less availability. The continuous mining of river sand has also affected the environment; ecologically and economically. Manufactured sand offers viable alternative to natural …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 1, 2016 · pp. 45–52 Read article
-
Experimental and Behavioral Study on Fly Ash Along with Lime to Make Bricks for Low Cost Housing Techniques
Abstract: Fly ash is the waste material which is usually dump or used in concrete today as admixture and also replace by cement in concrete proportion and give equivalent strength to structure. A lot of research has been carried out for effective use of fly ash. As we know today fly ash bricks overcame to normal clay burnt bricks in all parameters like compressive strength, water absorption, durability, mortar profit, finishing …
Published in Recent Trends in Civil Engineering & Technology · Vol. 5, Issue 2, 2015 · pp. 30–41 Read article
-
Experimental Investigation on Concrete with Partial Replacement of Cement by Fly Ash
Abstract: Fly ash is increasingly used as a supplementary cementitious material to partially replace cement in concrete. This paper presents an experimental investigation on the strength properties of concrete with varying percentages of fly ash replacement, from 0% to 25% by weight. The fresh, hardened, and durability properties of high performance concrete with fly ash percentages of 5%, 10%, 15%, 20% and 25% were studied. The test results indicate that 20% …
Published in Recent Trends in Civil Engineering & Technology · Vol. 13, Issue 3, 2023 · pp. 1–14 Read article
-
Experimental Studies on the Surface-Driven Capillary Flow of Dyed Water in Multistage Microfluidic Bends
Abstract: AbstractA single three-stage and a pair of two-stage microfluidic bends are fabricated. SU-8 as negative photoresist is used to fabricate the stamp by maskless lithography and diamond like carbon (DLC) coating. Microchannel structures are fabricated using polymethylmethacrylate (PMMA) by hot embossing lithography. Direct bonding technique is used to fabricate the leakage-free sealing in microfluidic bends. The leakage-free surface-driven capillary flow is recorded by CMOS camera. This work will be useful …
Published in Recent Trends in Fluid Mechanics · Vol. 4, Issue 3, 2017 · pp. 29–34 Read article
-
A Review of Experimental and Numerical Investigation on the Heat Transfer in Micro-Channel Heat Exchanger for Various Nano Fluids
Abstract: AbstractA tremendous amount of work has been carried out on micro and nanoscale heat exchanger. Cooling requirement is increasing day by day in field of, high performance Aircraft gas turbine engines, Heat pumps, Air conditioning, Heat recovery ventilators, Integrated circuits (IC), VLSI devices, Computer chips, Printed circuit boards and biomedical applications etc. Many investigators focused on parameters such as Reynolds number, cross cut length, pressure drop, particle concentration of Nano …
Published in Recent Trends in Fluid Mechanics · Vol. 5, Issue 3, 2018 · pp. 1–7 Read article
-
Design of Experiments of an Effective Thermal Conductivity of Composite Matrix by using Numerical Simulation
Abstract: Effective thermal conductivities of fillers and matrix reinforced composite models are analysed by using Finite Element (FE) simulation. The process parameters of different filler concentrations, filler piece arrangements and thermal conductivity ratio are analysed by Design of Experiment. In this study, simulation based on fully replicable five -factor, five-level central composite design. Regression models are developed to analyze the effects of process parameter. The responses are analyzing the direct and …
Published in Recent Trends in Fluid Mechanics · Vol. 6, Issue 2, 2019 · pp. 1–18 Read article
-
Experimental Aspects of Surface-Driven Capillary Flow in Microfluidics
Abstract: AbstractAt least one of the length, width or height must be less than one millimetre in any microchannel. The fluidic motion in any microchannel is called the microfluidic flow. Surface-driven capillary flow is also called the passive capillary flow in microfluidics. Polymers are common materials to fabricate the microfluidic devices. In this work, different aspects of surface-driven capillary flow are briefly explained. Surface-driven capillary flow has many bioengineering applications that …
Published in Recent Trends in Fluid Mechanics · Vol. 7, Issue 1, 2020 · pp. 15–19 Read article
-
Design and CFD Analysis with Experimental Testing of Exhaust Manifold
Abstract: The exhaust manifold undergoes back pressure problems. If the design of the manifold consists of sharp edges or bends which will tend to create turbulence and increase in pressure. Due to increase in turbulence it can cause an increase in back pressure. As the back pressure increases it tends to improper scavenging of the exhaust gases. So the improper scavenging of the gases leads to improper burning of fuel which …
Published in Recent Trends in Fluid Mechanics · Vol. 8, Issue 3, 2021 · pp. 6–23 Read article
-
Autonomous Optimization, Method Design of Casting and Its Experimental Validation: A Case Study
Abstract: The metal casting is a complicated but a mass production manufacturing technique. But on the otherhand, the chances of casting rejection are also more if proper attention is not made at every stage ofcasting production. In the metal casting process, higher yield and minimum defects level are expectedby the foundry industries. In the present global and competitive world metal casting industries needsto perform efficiently with a reduction in rejections. This …
Published in Trends in Machine design · Vol. 8, Issue 1, 2021 · pp. 1–10 Read article
-
Design, Analysis and Experimental Study of Worm and Worm Gear Pair for Plug Valve Application
Abstract: The present work deals with the design procedure, load carrying capacity, mathematical modelling,analysis of worm and worm gear for plug valve application. The plug valves are used in various fluidservices applications. It performs well in slurry applications. It is also used in air, gaseous servicesand oil piping systems and a like applications. In plug valve the main and important function of theworm gear drive is to reliably transmit torque and …
Published in Trends in Machine design · Vol. 8, Issue 1, 2021 · pp. 11–20 Read article
-
Analysis of Factors Affecting the Welded Joint using Design of Experiments: A Review
Abstract: The welding process over the period of time has grown into a more formidable process. Its application has also increased manifolds. However, with the increase in applications, it is also important to know the about the factors which affects the most on the strength of the welds. In this paper, the tensile strength of the welded joint has been considered. In this research, the Gas Metal Arc Welding has been …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 3, 2018 · pp. 72–75 Read article