Search
1265 articles for “and strength”
-
Interfacial Bonding Efficiency in Jute-Carbon Fiber Polyester Matrix Composites Evaluated Through Short Beam Shear and Interlaminar Fracture Toughness Testing
Abstract: The natural Fiber–synthetic Fiber hybrid composites are jute–carbon Fiber hybrid in polyester matrix which could be used in semi-structural applications of automotive, construction and marine industry as an eco-friendly and cost-effective alternative of conventional carbon Fiber reinforced polymer. But the hydrophilic nature of jute Fibers and the relatively inert surface of carbon Fiber's cause weak bonding at the interface of the polyester matrix, which causes premature delamination, poor interlaminar shear …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Experimental Study and Comparative Analysis of Fly Ash, GGBS, and Silica Fume in Nominal Concrete and Ternary Blended M25 Concrete
Abstract: This study examines the effects of partially substituting 30% of cement by weight with ternary supplemental cementitious materials (TSCMs) with mix proportions of M1, M2, and M3. These materials include fly ash (10%,15%,15% in M1, M2, and M3), ground granulated blast furnace slag (GGBS) (10%,8%,10% in M1, M2, and M3), and silica fume SF (15%,10%,5% in M1, M2, and M3) on the mechanical and durability properties of M25 grade concrete …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 43–50 Read article
-
Ultrasonic Dispersion of Halloysite Nanotubes for Enhanced Mechanical, Thermal, and Morphological Performance of Epoxy Composites
Abstract: Halloysite nanotube (HNT)-reinforced epoxy nanocomposites were prepared by mixing HNT with bisphenol-A epoxy (LY 556) using ultrasonication, followed by compression molding. HNT contents of 0–5 wt.% were used. The composites were evaluated for tensile strength, flexural strength, Shore D hardness, Izod impact strength, and thermal stability using thermogravimetric analysis (TGA). The fractured tensile surfaces were also examined to understand the failure mechanism and interaction between HNT and the epoxy matrix. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Eco-friendly Azadirachta Indica Ash and Miscanthus Fiber Brick for Carbon Neutrality Environment
Abstract: Naturally grown fiber are not utilized properly they are neglected as wastes. These resources are thrown away due to insufficient research being conducted to discover viable uses for naturally existing fibres. These byproducts have a wide variety of applications in the manufacturing sector, notably in the construction sector. The prospective applications of miscanthus fibre, which may be found growing wild in uncultivated places, are investigated in this research. The production …
Published in Journal of Polymer & Composites Read article
-
A Comprehensive Review of Concrete Containing Magnetically Treated Water
Abstract: In Present scenario, Construction has benefited greatly from the characteristics of concrete and the magnetism of water. The procedure of permitting water to pass through the magnetic field is part of creating magnetised water, utilizing those properties of concrete that can affect such as compressive strength, workability, porosity, permeability, durability, water absorption capacity, hydration rate and aqueous ratio. Reduced cement usage and improved mechanical and technical qualities of concrete are …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 52–64 Read article
-
Design and Analysis of a Metal Lined Composite Overwrapped Pressure Vessel
Abstract: This study presents a comprehensive investigation into the mechanical behavior of a metal lined composite overwrapped pressure vessel, designed for high-pressure storage applications. The design approach is dependent upon fiber material constants and dome shape factor. The study begins with obtaining dome coordinates and maintaining winding angles according to a geodesic path equation. Thickness estimation for the portion of cylindrical shell and domes are determined through netting analysis and cubic …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 215–232 Read article
-
Investigation on Basalt Based High Performance Concrete
Abstract: The study aims to explore the potential of basalt fibers and metakaolin in enhancing the mechanical, durability, and microstructural characteristics of concrete. The investigation begins with a thorough literature review is conducted to ascertain the present status of information regarding metakaolin, basalt fibers, and their impact on concrete. The experimental program involves the formulation of concrete mixtures with varying percentages of basalt fibers and metakaolin, alongside a control mixture without …
Published in Journal of Polymer & Composites · Vol. 11, Issue 10, 2023 · pp. 1–8 Read article
-
Geopolymer Concrete with Cenosphere as Fine Aggregate: A Material Characterisation
Abstract: Geopolymer concrete (GPC) is regarded as the successor to traditional concrete as it eliminates the requirement for conventional Portland cement during its manufacturing process, hence decreasing CO2 emissions. This study employed Cenosphere, which are lightweight fine materials, to partially substitute the volume of sand in GPC. Cenosphere was utilized in proportions of 20%, 40%, 60%, and 100%. This experiment examined the fresh and hardened characteristics, durability against freezing and thawing, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 143–151 Read article
-
Impact of Red Stone Dust and Polymer Fabric in Enhancing the Properties of Black Cotton Soil
Abstract: To enhance the mechanical properties of problematic black cotton soil, engineers are focusing on reinforcing the soil with geosynthetic materials. This attention is particularly directed towards improving the strength characteristics of black cotton soil, given its inherent challenges associated with volume changes and plasticity. In this comprehensive study, red stone dust waste is introduced in varying percentages ranging from 5% to 35% to stabilize the black cotton soil. The goal …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 35–43 Read article
-
Advancements in graphene reinforced metal matrix composites: A comprehensive review
Abstract: The Present pollution norms insist automobile manufacturers to make use of ultra-high specific strength materials i.e., materials ahead of conventional metal matrix composites (MMCs) with micro-sized reinforcements. With the advent of nanomaterials, nanocomposites are being developed with properties that overcome the limitations for metals or composites with micro-sized reinforcements. In recent years, the family of graphene-based materials, in particular, graphene nanoplatelets (GNPs) reinforced MMCs offering promising solutions to revolutionize the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 177–189 Read article
-
Effects of Nano B4C Addition on the Solidification Behavior of Al-2219 Alloy Composites
Abstract: The inclusion of nano B4C particulates in Al-2219-Nano B4C alloy was investigated to understand their impact on hardness and wear characteristics. 500 nm-sized nano B4C particulates are used as reinforcements for structures in the Al2219 alloy matrix. The nanocomposites were fabricated using the two-stage liquid stir melt method with varying weight percentages (2, 4, 6, and 8 wt. %) of Nano B4C in the Al-2219 alloy matrix. Renewable energy dispersive …
Published in International Journal of Manufacturing and Production Engineering · Vol. 2, Issue 1, 2024 · pp. 31–38 Read article
-
Enhanced Durability and Performance of Reinforced Concrete Beams through CFRP Wrapping: An Experimental Investigation
Abstract: Globally, maintaining and repairing aging reinforced concrete structures poses a significant challenge for the construction industry. Numerous structures built before modern earthquake-resistant design codes lack adequate seismic resilience. Additionally, evolving service requirements often necessitate strengthening existing structures to handle increased loads. While past research explored the effectiveness of various Fiber Reinforced Polymer (FRP) wrappings under specific conditions, limited studies have comprehensively compared the performance of Carbon Fiber Reinforced Polymer (CFRP) …
Published in Journal of Polymer & Composites · Vol. 12, Issue 4, 2024 · pp. 37–49 Read article
-
Phase Transformation of Manganese Steel: A Role of Alloying Elements
Abstract: Low alloyed steels that are both strong and ductile are the primary focus of new material concept work due to economic considerations. One key to making good use of these materials is applying the right heat and thermo mechanical treatments. Phase transitions can be influenced by using different alloying procedures. Microstructural evolution and mechanical characteristics were investigated in relation to varying manganese, silicon, and chromium levels. Developing high-strength flat rolled …
Published in Trends in Mechanical Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 15–20 Read article
-
Boron Nitride Unleashed: Revolutionary Insights into Its Superhard Phases and Machining Aptitude
Abstract: Exploration from the prehistoric era has proven steel to be a hard substance. According to research, the four main crystalline forms of boron nitride are graphitic, cubic, rhombohedral, and wurtzitic. Better hard materials for industrial processes have been provided by diamond, hard ceramic, and cermet in the process of developing the front of the script, which is descriptive. Turning, cutting, drilling, boring, and grinding of hard materials have been linked …
Published in Journal of Catalyst & Catalysis · Vol. 11, Issue 2, 2024 · pp. 17–24 Read article
-
Comparative analysis of carbon fibre and E-glass fibre characteristics
Abstract: In the contemporary automotive industry, the imperative focus on energy efficiency has driven the central role of lightweight, addressing challenges such as emissions reduction and fuel efficiency. Extensive research is underway to develop lightweight materials enhance recyclability, integration feasibility, and overall fuel efficiency These experiments were conducted in agreement with ASTM D638, ASTM D790-03, and ASTM D790 standards to ensure adherence to industry standards and facilitate meaningful comparisons. For the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 253–267 Read article
-
Characterization and Fabrication of Particle Board from Banana Fiber and Sawdust as A Hybrid Composite
Abstract: The current global landscape emphasizes the search for eco-friendly and regenerative materials. Utilizing environmentally available fibers in conjunction with polymeric resins through efficient manufacturing processes offers a cost-effective solution with high-quality standards. Polymer matrix composites with fiber reinforcements possess several advantages, including low production costs, ease of fabrication, and improved material properties, making them applicable in a wide range of industrial contexts. This paper emphasizes the creation of Particle boards …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 192–200 Read article
-
Mechanical Properties, Viscoelastic and Water Absorption Properties of Biocarbon-Reinforced Composites
Abstract: Biocarbon-reinforced polymer composites have emerged as a sustainable alternative to conventional composites, combining environmental benefits with promising material properties. This study explores the effect of varying biocarbon content (0%, 10%, 20%, and 30% by weight) on the mechanical, viscoelastic, and water absorption properties of a polypropylene (PP) matrix. Tensile strength tests reveal that incorporating 10% biocarbon yields the highest strength at 35 MPa, attributed to enhanced interfacial bonding. However, at …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 145–157 Read article
-
Comparative Experimental Investigation of Infill Pattern and Infill Density on Fused Deposition Modeling (FDM) Process Characteristics of Polylactic Acid (PLA)
Abstract: Additive manufacturing is the potential and emerging technology widely being used to produce quality products with complicated profiles and customized features. Fused Deposition Modelling (FDM) process, a type of additive manufacturing technology using filament made of thermoplastic which is melted and subsequently extruded through nozzle. The main input process parameters of FDM are wall thickness, infill density, layer height, bed temperature, layer thickness, infill pattern, nozzle temperature etc. In this …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 335–345 Read article
-
Pregnancy-Induced Post-Natal Back Pain
Abstract: Pregnancy-induced post-natal back pain (PNBP) is a common condition that affects many women following childbirth, significantly impacting their quality of life and physical functioning. The physiological and anatomical changes during pregnancy, such as weight gain, altered posture, and hormonal changes, contribute to the onset of back pain. As the body prepares for delivery, the pelvis and spine undergo structural shifts that can strain the muscles and ligaments supporting the lower …
Published in International Journal of Women's Health Nursing And Practices · Vol. 3, Issue 1, 2025 · pp. 25–31 Read article
-
Failure Analysis of Hybrid Natural/Synthetic Fiber Composite Laminates in The Application of Hybrid Composite Pressure Vessel
Abstract: Composite laminates are frequently utilized in multiple sectors. The growing complexity of composites in aircraft applications necessitates hybridization of these materials. These hybrid laminates consist the combination of one natural fiber and two selected synthetic fibers. This work investigates three different six-layer hybrid composite laminate combinations: Jute2/Carbon2/Jute2, Jute2/Glass2/Jute2, and Carbon2/Glass2/Carbon2, with helix angles of 0° and 90° and a volume fraction of 50% fiber content. Each specimen is fabricated utilizing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 85–98 Read article