Search
261 articles for “dispersion”
-
Catalyst-Driven Degradation and Failure Analysis of Intergranular Cracking in 316H Studded Pipes under Refinery Heat Recovery Conditions
Abstract: A failure analysis investigation was carried out on a high-temperature studded pipe used in a convection module for heat recovery in an oil and gas refinery application after leakage was detected during pre-commissioning hydrotesting. The investigated pipe was manufactured from AISI 316H austenitic stainless steel, and carbon steel studs had been joined to its outer surface by high-frequency resistance welding. Two leaks were reported in the pipe under investigation, and …
Published in Journal of Catalyst & Catalysis · Vol. 13, Issue 1, 2026 Read article
-
Hybrid Polymer Composites Containing GGBS and Copper Slag: A Review of Mechanical Behavior and Interfacial Mechanisms
Abstract: Over the past few years, there has been a push to seek sustainable solutions through material science in the field of industrial by-products that can be used in polymer composite systems. Two such substances are ground granulated blast furnace slag (GGBS) and copper slag that have demonstrated a promising potential because of their abundance and useful physical and chemical properties.This review is dedicated to the application of GGBS and copper …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 43–50 Read article
-
AI-Driven Inverse Design of Functionally Graded Bio-Nanocomposites for Sustainable High-Barrier Packaging
Abstract: Multilayer plastic packaging realizes high barrier performance through laminated heterogeneous structures, but the heterogeneous structure has severe end-of-life challenges caused by the interfacial incompatibility of materials and the poor recyclability. This study proposes the inverse design of functionally graded PLA-nanoclay composite films by reinforcement learning as a monolithic alternative to traditional multilayer systems. Twin-screw extrusion is designed as a continuous control Markov decision process, and proximal policy optimization (PPO) is …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1547–1564 Read article
-
Effect of Red Mud Loading on the Thermal and Mechanical Performance of Polypropylene Composites
Abstract: Waste red mud (RM) serves as a low-cost and sustainable filler material in a polypropylene (PP) matrix. This study investigate the effects of different red mud contents on the dynamic mechanical and thermal properties of polypropylene-red mud (RM-PP) composites where red mud levels range from 0% to 40% (based on weight percentage). Fourier Transform Infrared Spectroscopy (FTIR) was conducted for verifying the presence of both polypropylene and red mud in …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 161–169 Read article
-
Tensile and Microstructural Behaviour of Friction Stir Welded AL7050 Hybrid Composites Reinforced with Multani Mitti and Cow Dung Ash
Abstract: The study examines Al7050 aluminum alloy composites made by stir casting and bonded by friction stir welding (FSW), supplemented with environmentally friendly Multani Mitti (MM) and cow dung ash (CDA). The study assesses the effects of different hybrid reinforcement contents (0–8 vol%) on the microstructural properties, hardness, and tensile behavior of the base alloy and its FSW joints. Tensile testing reveals an initial decline at 2% reinforcement but a notable …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 78–89 Read article
-
Interfacial Engineering of Carbon Fiber/Epoxy Laminates Using Functionalized Graphene Nanoplatelets: Experimental and Numerical Study
Abstract: Current research work studies the influence of amines(–NH₂) and carboxyl(–COOH) functionalized graphene nanoplatelets on the mechanical and thermomechanical behavior of unidirectional hybrid composite. Composites having different graphene concentration from 0 to 0.7 wt% were fabricated, characterized and analyzed for multiple testing - tensile testing, dynamic mechanical analysis (DMA) and Fourier transform infrared spectroscopy (FTIR). Tensile testing indicates better elastic modulus and tensile strength due to efficient load transfer between nanoparticles …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 61–77 Read article
-
Structure–Property Modeling of Cement-Based Multi-Component Composites Using Ensemble Machine Learning and Explainable Feature Attribution
Abstract: Accurate prediction of compressive strength is central to structure–property optimization, quality control, and sustainability-driven design in cement-based composite materials. Cementitious systems represent heterogeneous multi-phase composites composed of reactive binder matrices and dispersed aggregate phases, whose macroscopic mechanical performance emerges from complex nonlinear interactions among constituents and curing-dependent microstructural evolution. This study develops a data-driven structure–property modeling framework to quantify the nonlinear dependence of compressive strength on multi-component composite composition and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 112–131 Read article
-
Fabrication and Mechanical Characterization of Hybrid Natural Fiber Reinforced Composites using Ferromagnetic and Graphite Fillers
Abstract: The past few years have seen a lot of interest in the creation of hybrid natural fiber composites because of their lightweight properties, environmental friendliness and their potential use in structures. The hybrid composite laminates in the current study were produced by the hand lay-up process by blending the natural fibers with the functional filler materials. Three types of composite structures were created and these are Natural Composite Material (NCM), …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 498–511 Read article
-
Development and Characterization of Rubber Composites using E-Waste Residue as Functional Filler
Abstract: In the present study, residue generated during the recycling of end-of-life printed circuit boards (PCBs) was utilized as a functional filler in natural rubber to fabricate eco-friendly composites using mixing and molding techniques. Chemical analysis of the residue revealed the presence of several metals, including copper, iron, lead, tin, and zinc. The presence of these metals highlights the need for proper recycling and safe management of PCB residues, as their …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 512–523 Read article
-
Polymer-Based Nanocomposite Coatings for Enhancing Solar Photovoltaic Panel Efficiency
Abstract: Environmental factors such as dust deposition, ultraviolet (UV) radiation, and surface reflection significantly reduce the performance of solar photovoltaic (PV) modules. This study investigates the development and performance evaluation of polymer-based nanocomposite coatings designed to improve the optical and surface properties of PV panel glass. A hybrid nanocomposite coating containing TiO₂ and SiO₂ nanoparticles dispersed in a polymethyl methacrylate (PMMA) matrix was synthesized using the sol–gel technique and deposited through …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 490–497 Read article
-
Enhancement of Mechanical and Tribological Properties of Aluminum-Titanium Carbide (Al-TiC) Metal Matrix Composites via Powder Metallurgy
Abstract: Metal matrix composites (MMCs) have emerged as a result of the increasing need for sophisticated lightweight materials with exceptional mechanical and tribological qualities. For structural and wear-critical applications, aluminum-based composites supplemented with ceramic particles such as titanium carbide (TiC) have shown great promise. In this work, aluminum-TiC composites made by powder metallurgy a process that guarantees even particle dispersion, regulated porosity, and the creation of near-net shapes are fabricated, mechanically …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 366–374 Read article
-
Polymer Composite-Assisted Crystal Engineering for Drug Synthesis and Property Control through Solid Solutions and Co-Crystals
Abstract: The long-standing problem of low aqueous solubility, which affects about 90% of all new drug molecules under development, requires an immediate need for alternative approaches apart from the usual practice of crystallization. Polymer-composite-assisted crystal engineering is a novel technique for overcoming the aforementioned problem. This involves the addition of accepted pharmaceutical polymers, such as HPMC, PVP, PEG, and Eudragit copolymers in a single process, which can promote nucleation, stabilize the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 172–189 Read article
-
Self-Healing Polymeric Composites Reinforced with Green Synthesized Nanoparticles
Abstract: The development of sustainable self-healing polymeric materials is critical for enhancing durability and service life in advanced engineering applications. In this study, zinc oxide (ZnO), magnesium oxide (MgO), and ferric oxide (Fe₂O₃) nanoparticles were green-synthesized using Allium cepa extract and incorporated into epoxy-based polymeric composites to improve mechanical, thermal, and self-healing properties. This bio-based synthesis is eco-friendly and safe alternative to harsh chemical techniques, utilizing natural antioxidants to stabilize the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 305–314 Read article
-
Microbially Modified Sustainable Cementitious Composites Using Industrial Ash Fillers
Abstract: The growing demand for sustainable, durable construction materials has driven the development of bio-engineered cementitious composites incorporating industrial by-products and self-healing mechanisms. This study investigates a microbially modified cementitious composite that integrates industrial ash fillers with bacteria-based self-healing technology to enhance mechanical performance and microstructural integrity while reducing cement consumption. Cement was partially replaced with industrial ash at 20%, 30%, and 40% replacement levels, and a uratolytic bacterial strain (Bacillus …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 331–350 Read article
-
Assessing Taila Bindu Pariksha as a Diagnostic and Prognostic test for Diabetes Mellitus
Abstract: Ayurveda has consistently emphasised on not just treatment of a disease but also how to diagnose it and further assess the prognosis. Ayurveda is blessed with different diagnostic tests which is broadly classified into Roga and Rogi Pariksha such as Ashtavidha Pariksha, Dashavidha Pariksha and Dwadashavidha Pariksha. These tests are used very rarely by just few Ayurvedic practioners as an important diagnostic and prognostic methods in different diseases. Taila Bindu …
Published in Journal of AYUSH: Ayurveda, Yoga, Unani, Siddha and Homeopathy · Vol. 15, Issue 2, 2026 Read article
-
Polymer-Mediated Electron Transfer in Eco-Friendly P3HT–rGO Nanocomposites for Optoelectronic Applications
Abstract: Conducting polymer–graphene hybrid nanocomposites have emerged as promising materials for next-generation optoelectronic applications owing to their solution processability, tunable interfacial properties, and mechanical flexibility. Recent studies have highlighted the importance of graphene–polymer hybrid systems in enhancing charge transport pathways, exciton dissociation efficiency, and interfacial stability in organic optoelectronic devices. Despite these advantages, a key challenge remains the efficient production of individual graphene sheets through the reduction of graphene oxide using …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 413–423 Read article
-
Modelling -Based Evaluation of Hybrid Natural Synthetic Fiber Polymer Composites for Sustainable Energy Applications
Abstract: The growing need of lightweight, high-performance, and green energy system materials has increased the research on hybrid polymer composites. This paper gives a modelling-based evaluation of polymer matrix composites which are reinforced using natural fibers like jute, sisal, bamboo in a combination with synthetic glass fibers to be used in sustainable energy sources. An analytical model has been used to assess the effect of hybrid fiber composition on mechanical, thermal, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 682–688 Read article
-
Design and Performance Analysis of Natural Rubber–Silica Nanocomposite Vibration Isolators for Household Appliances
Abstract: Natural rubber (NR) nanocomposites reinforced with surface-modified precipitated silica (SiO2) were synthesized through a two-roll mill compounding and compression-moulding process, then systematically evaluated as passive vibration isolator materials for domestic washing machine applications. Five silica loadings 0, 5, 10, 15, and 20 phr were investigated. A comprehensive characterization suite encompassing tensile testing, Shore A hardness, dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) revealed clear structure–property …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 554–560 Read article
-
Synergistic Effects of Hybridized Nano-Silica and Hemp Fiber Reinforcement on Bio-Epoxy Composites
Abstract: Natural fiber-reinforced bio-epoxy composites have become promising sustainable alternatives to conventional synthetic-fiber petroleum-based materials, but are often limited by low fiber-matrix interfacial bonding, low thermal stability, and high moisture absorption which limit their application in structural applications. These issues are discussed in this work, by carrying out a systematic investigation of the synergistic effects of the hybridization of nano-silica particles with alkali-treated hemp fibers in a bio-epoxy matrix the composites …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 214–228 Read article
-
Heavy Metal Removal from Textile Industrial Effluent using Banana Exocarp Derived Cellulose Acetate Graphene Nanocomposite Membranes
Abstract: The disposal of textile effluent is responsible for serious human health concerns and above all environmental concerns to all kind of species. This indicates that there is immediate and urgent need of emerging, efficient with sustainable recycling technologies. In this paper, banana exocarp as agriculture-based waste, in terms of substrate was utilised as major raw material. The extracted cellulose from the substrate with homogeneous acetylation process, transformed into cellulose acetate …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 51–62 Read article