All articles
817 articles
-
Experimental analysis of wind turbine blade (HAWT) with recycled carpet waste polymer composite material
Abstract: The term "carpet" is often used interchangeably with "rug," but there is a technical distinction. Rugs are generally smaller and can be easily moved, while carpets are typically larger and cover a significant portion of the floor. Carpets are commonly used to enhance the comfort of indoor spaces, provide insulation, and contribute to the overall design and atmosphere of a room. Polymer composite materials also known as polymer matrix composites …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 259–265 Read article
-
The Impact of Crosslinking Polyvinyl Alcohol with Glutaraldehyde on Toughness: A Statistical Analysis Using the Turnkey HSD Method
Abstract: The widespread use of non-biodegradable polymers exacerbates problems with global warming and other environmental difficulties. These problems necessitate the development of biodegradable polymers as a solution. In this research, we analyze the utilization of crosslinked polymer by its processing of polyvinyl alcohol (P V A) crosslinked with glutaraldehyde (G L U T). After curing for 24 hours in 2 moles of sulfuric acid (H2SO4), the plasticized alcohol has been cross-linked …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 213–219 Read article
-
An experimental investigation of Prosopis Juliflora Biodiesel’s performance and emission characteristics
Abstract: Fossil fuels are currently in crisis due to their higher cost, their increasing use, and their scarcity. In view of the large number of cars on the road and the emission levels caused by combustion ignition engines, fuel substitutes are sought. Diesel is the most expensive fuel on the market, so biodiesel is a good alternative. Aside from its low toxicity, it reduces greenhouse gas emissions, does not emit sulphur, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 67–75 Read article
-
An experimental study on flexural behavior of RC beams of Alccofine based engineered concrete infusing steel fibres
Abstract: The innovations in concrete being engineered to the specific requirements have found a new dimension under sustainability. Alccofine is a sustainable construction material derived from GGBS. The primary objective of the study is to explore the potential of Alccofine particles in varying proportions in combination with 0.5% steel fibers to uplift the flexural strength of the engineered concrete. As concrete is known to be a brittle material once hardened, exhibits …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 87–97 Read article
-
Control of Powdery Mildew of Sheesham (Dalbergia Sissoo) in India through Radionics Computer and Nanotechnology from Kuwait
Abstract: Powdery mildew is a common fungal disease caused by different fungi on different hosts including field crops, vegetable crops, fruit trees, ornamentals, and woody trees. Sheesham (Dalbergia sissoo) is one of the most common and important timber and woody trees in the Indo-Pak subcontinent. An experiment was conducted to control the growth/spread of powdery mildew caused by the fungus (Phyllactinia dalbergiae) growing on ‘Sheesham’ (Dalbergia sissoo) tree leaves. The infected …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 106–113 Read article
-
Comparative Assessment of Antibacterial Effectiveness, Bioactivity, Fluoride Release, and Microleakage of Various Bioactive Smart Composites: An In Vitro Investigation.
Abstract: The demand for dental composites with enhanced properties has led to the development of bioactive smart composites aimed at addressing multiple aspects of restorative dentistry. This in vitro investigation aimed to conduct a comparative assessment of the antibacterial effectiveness, bioactivity, fluoride release, and microleakage properties of various bioactive smart composites. Bioactive smart composites are emerging dental materials designed to promote remineralization and inhibit bacterial growth, thereby enhancing the longevity of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 76–86 Read article
-
Review paper on concrete mix design optimization using machine learning based algorithm
Abstract: Concrete is an essential part of most construction works in civil engineering. The mix design of concrete is usually specified in terms of prescription or performance-based approach. One of the most important procedures is proportioning the concrete mix, which requires taking several safety precautions to get the proper amounts of elements like cement, aggregate, water, and admixtures. The current study offers a thorough analysis of the Artificial Neural Networks (ANN) …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 311–320 Read article
-
Comparative Buckling Load Analysis of Thin Functionally Graded Material Plates with Variable Distributions: Power Law vs. Sigmoidal vs. Exponential
Abstract: A comprehensive comparative analysis of buckling load behavior in thin Functionally Graded Material (FGM) plates with variable material distributions is presented in this paper. FGMs, characterized by gradient composition, possess unique mechanical properties suitable for diverse engineering applications. The study focuses on three distinct distribution functions: Power Law, Sigmoidal, and Exponential, each exerting different influences on the material gradient. Finite Element Analysis is utilized in exploring the buckling response for …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 98–105 Read article
-
Improvement of mechanical properties for PMMA based Denture material
Abstract: Denture material properties can be improved by various fiber addition. The most often used denture materials are polymethyl methacrylate (PMMA) resins; nevertheless, they do not have a high flexural strength (FS). This investigation compared the mechanical characteristics of an injection-molded polyamide. Deflex, an additional injection-molded PMMA base material, SRIvocap, and a typical compression-molded PMMA (Meliodent). The flexural qualities (deflection, bending strength, and bending modulus) of 100 different denture base materials …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 155–165 Read article
-
Fabrication and drilling characterization of Hemp & Grewia-Optiva hybrid composite and comparison with ANN model
Abstract: In recent days the use of natural fibers has increased over synthetic fibers due to various advantages. The alkali treatment for these natural fibers further improves the adhesion between fiber and matrix and greatly enhances the mechanical properties of the composite. The present study involves the fabrication of a hybrid composite using the alkali-treated (5% NaOH concentration) natural fibers – Hemp &Grewia-optiva as reinforcement material and epoxy as a matrix …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 138–146 Read article
-
Electro-chemical treatment of graphite oxide: preparation and Characterization of high quality Graphene material
Abstract: With the enlargement of flexibility and suitability in material industries, high-performance thermal management materials are demanded with high thermal conductivity and electrical insulation are growing. In recent years, graphene has received a numerous focus from science community due to its high thermal conductivity and electrical insulation. Fabrication of light weight graphene and its derivatives as graphene Oxide (GO) and reduced graphene oxide (rGO) via facile processing method is yet a …
Published in Journal of Polymer & Composites Read article
-
Environment- friendly Pavement Construction Using Plastic Trash and Reclaimed Asphalt Pavement-An Overview
Abstract: Plastic pollution has emerged as a significant environmental concern, with detrimental effects on ecosystems and human health. As a waste product contaminating air, water, and land, plastic poses a grave threat to the environment, perpetuating a global crisis. Its non-biodegradable nature means that once produced, plastic persists indefinitely, accumulating in landfills, water bodies, and natural habitats. This widespread accumulation of plastic waste not only compromises the aesthetic value of landscapes …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 116–123 Read article
-
Investigation on Dry Sliding Wear Behaviour of AlSi7Mg0.3/B4C/ZrO2 Hybrid Composites using Taguchi Method
Abstract: Hybrid Aluminium/Boron carbide/Zirconium oxide (AlSi7Mg0.3/B4C/ZrO2) composites were fabricated utilizing stir casting technique by varying boron carbide content (4wt.%, 8wt.% and 12wt.%) and utilizing a fixed amount (4wt.%) of zirconium oxide particles. Optical microscopy revealed that B4C and ZrO2 particulates were dispersed uniformly in AlSi7Mg0.3 matrix. Dry sliding wear experiments were carried out utilizing the pin-on-disc tribometer with various levels of applied loads, sliding speeds and weight percentage of boron carbide …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 166–177 Read article
-
Temperature dependence of Schmidt number of composite material based liquid lithium
Abstract: This work presents a simple formalism for Schmidt number and its temperature dependence for liquid lithium. It is explained that the temperature dependence of Schmidt number (Sc = η/ ρD) can be understood through dependence of topological-short-range-order (TSRO) parameter on temperature. Expression for Schmidt number has been deduced in terms of average potential energy US of superficial core, probability of diffusional displacement (P) and the TSRO parameter (x) . Calculations …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 206–212 Read article
-
Advancements in Seismic Analysis Based on Shear Walls Composite Materials
Abstract: In this study more than 30 research papers are thoroughly reviewed in the area of Seismic Analysis based on Shear Walls. Seismic performance evaluation is used to assess a construction's seismic behavior in accordance with predetermined performance criteria. These methods have been applied in a number of assessment studies to investigate the seismic behavior of shear wall designs, and their findings have advanced the field overall. Shear wall is works …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 235–243 Read article
-
Incorporating Material Fatigue Parameter Determine in The Rolling & Sliding Contact Fatigue Analysis of Gears
Abstract: As the material's intricate stresses and strains are always shifting during phases of loading, determining the predicted equipment working under rolling-sliding contact loads and their fatigue lives (wheels, bearings, and gears) is particularly difficult. Another difficulty is not knowing the precise characteristics of the material used to make the components, which is particularly noticeable. when it comes to heat-treated components, where the material characteristics' values can differ greatly among the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 4, 2024 · pp. 1–5 Read article
-
Numerical simulation and Artificial neural network illustration of phase-change material integrated into lattice structures printed in 3D
Abstract: This work examines the phase change material (P.C.M.) deposited in various lattice formations—such as “S.C., B.C.C., and F.C.C”.—at varied characteristics. The test concentrates on comprehending heat transport properties and thermal activity throughout the “melting and solidification processes”. The heater's maximum temperature, P.C.M. “melting and solidification”, and Nusselt number are among the essential factors examined. According to the findings, the heater's maximum temperature drops as porosity increases. Although the Nusselt values …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 175–183 Read article
-
Review of Input Selection Criteria; Comparison of Popular Methods Used in Water Stress Analysis.
Abstract: This paper examines input variables and their respective selection criteria intended for application in methodologies addressing water scarcity. It presents a comparative analysis of prominent approaches utilized in assessing water stress within urban contexts, such as the Analytic Hierarchy Process (AHP), Multiple Criteria Decision Making (MCDM), Geographic Overlay Decision (GOD), and System for Integrated Assessment of City Transformation towards Sustainability (SINTACTS). The principal aim is to scrutinize prevailing input parameters …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 311–319 Read article
-
Investigation on bi-layer knitted fabric produced using recycled polyester and banana fiber for improved moisture and thermal comfort properties
Abstract: This research investigates thermal comfort characteristics of bi-layer knitted fabrics made of banana fibers and recycled polyester (rPET). The main aim is to maximize thermal comfort of textile products by taking advantage of the distinctive characteristics of these two varieties of eco-friendly materials. Recycled polyester and banana fibers were combined to make the bi-layer knitted materials, which is produced as separate inner and outer layers to maximize performance. The features …
Published in Journal of Polymer & Composites Read article
-
Synthesis and Functional Group Analysis of Solution Processed Zinc Oxide Thin Film Grown on Polyethylene Terephthalate
Abstract: Flexible electronics field is growing every day. Existing technology is facing issues like brittleness, toxicity, inadequacy. Fabrication cost increases in processing of such materials. In this work, zinc oxide nanoparticles synthesized by solution processing technique were used to grow 120nm thick thin film (TF) on Polyethylene terephthalate (PET). This method reduces the processing cost and Zinc Oxide (ZnO) is cheaper and abundant in comparison to other semiconductors option. Material was …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 56–66 Read article