Wear Rate
7 articles · search the full text for this term
-
Experimental Assessment and Statistical Argument of Al-Si/CSA/MoS2 Hybrid Composites for Mechanical and Tribological Characteristics
Abstract: To augment the mechanical and tribological properties of Al-Si matrix composites complement with molybdenum disulphide (MoS₂) and coconut shell ash (CSA), a mixed experimental and Face-Centered Composite (FCC)strategy was employed. A liquid metallurgical method called stir casting was used to create hybrid composites with 5–15 wt.% CSA and 1–3 wt.% MoS₂. A FCC experimental design with thirty runs was used to thoroughly evaluate the materials. This design allowed for the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 792–802 Read article
-
Optimizing Parameters for Dry Sliding Wear Control in Stir-Cast AA7050/SiC Composites
Abstract: Using a pin-on-disc tribometer, this study examined the dry sliding wear behavior of AA7050/SiC composites. The production of this metal matrix composite was achieved through the stir-casting process, which involved an initial step of melting the AA7050 alloy, followed by the careful introduction of silicon carbide (SiC) particles, stirring to achieve uniform dispersion, and finally, casting the molten mixture. Wear rate (WR) was determined by three operational parameters: SiC reinforcement …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1624–1635 Read article
-
Fabrication and Experimental Investigation on Mechanical Properties of Quartz Particulate Reinforced Aluminium Composite
Abstract: Composites are processed by adding a reinforcement phase in a base metal. The base material is known as a matrix and the constituent that is added is called reinforcement. The matrix acts as a support while the reinforcements attach themselves in their respective positions which results in the synthesis of a material which has different mechanical and thermal properties compared to their raw materials. Since aluminium is used as a …
Published in Journal of Production Research & Management · Vol. 14, Issue 3, 2024 · pp. 19–25 Read article
-
Tribological Study on SiC+Graphene Reinforced Al319 Composite andOptimization of Stir Casting Parameters
Abstract: The aluminium 319 (Al319) is a commonly used material for fabricating automobile components. Due to continuous friction and vibration, those components are subjected to significant wear. Therefore, it is necessary to improve the wear characteristics of this Al319. Hence, in this study Silicon Carbide (SiC) and Graphene nanoparticles (GNPs) are reinforce to Al319 via electro-magnetic stir casting method to optimize wear characteristics without its affecting mechanical properties. Various proposition of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 105–123 Read article
-
Influence of the Load, Sliding Speed, and Weight Fractions on Wear of a Hybrid Aluminium Metal Matrix Composite
Abstract: The vital focus of the research is intended in examining the aspect that impact the rate of wear for a hybrid aluminium metal matrix composite. The percentages of two reinforcements that are employed, the weight, and the sliding speed are the variables taken. The procedure entails employing the vortex-stir casting process to produce the hybrid composite. Utilizing a pin-on-disc apparatus, the fabricated composite materials are evaluated in compliance with the …
Published in Journal of Polymer & Composites · Vol. 11, Issue 13, 2023 · pp. 188–198 Read article
-
Tribological Behaviour of En 31 Bearing Steel Against Altin, Alcrn and Crn Coated High Speed Steel
Abstract: Mechanical parts like bearing in modern machining systems are often subjected to wear and friction causing high heat generation at the interacting zones leading to reduced lifecycle and increased energy consumption of machinery. In this investigation friction and wear characteristics of bearing material EN31 steel against the CrN, AlCrN and AlTiN deposited on high speed steel as counter material is presented. Tribological tests are conducted on a pin on disc …
Published in Journal of Polymer & Composites · Vol. 9, Issue 2, 2021 · pp. 97–108 Read article
-
A Technical Review on the Wear Rate of Deep-Hole Drilling Process Based on BTA (Boring and Trepanning Association) Technique
Abstract: Deep-hole drilling of hard materials like carbon steel and super alloys like Inconel-718 is a very complicated process as the wear rate of BTA inserts is quite high as compared to other materials. In this review paper author aims to study the various factors affecting the wear rate and the type of wear occurring in different inserts used for deep-hole drilling of the above mentioned materials. It also emphasizes on …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 3, 2017 · pp. 18–23 Read article