Polylactic Acid
6 articles · search the full text for this term
-
Corn Husk Fiber–Reinforced PLA Biocomposites: Mechanical, Thermal, and Biodegradation Performance
Abstract: The increasing environmental burden caused by conventional petroleum-based plastics has driven significant interest in the development of sustainable polymer composites reinforced with renewable natural fibers. In the present work, corn husk fiber (CHF), an agricultural waste by-product, was utilized as a reinforcing phase in a polylactic acid (PLA) matrix to fabricate eco-friendly biocomposites. Composite samples with varying fiber loadings (0–40 wt.%) were produced through twin-screw melt blending followed by compression …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 312–327 Read article
-
Perspectives of 3D-Printed Polylactic Acid-Based Composites Reinforced with Natural Fibers
Abstract: The growing demand for sustainable and biodegradable materials has led to the development of polylactic acid (PLA)-based composites reinforced with natural fibers. This study investigates the mechanical, thermal, printability, and environmental performance of 3D-printed PLA/Natural Fiber composites, addressing key challenges in fiber-matrix compatibility, structural integrity, and biodegradability. Natural fiber reinforcement enhanced Young’s modulus and flexural strength, but excessive fiber content led to agglomeration, reduced tensile strength, and increased brittleness. Thermal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 649–664 Read article
-
Finite Element Formulation for Mechanical Buckling of FGM Plate Exposed to Various Boundary Conditions
Abstract: Mechanical buckling analysis of functionally graded (FG) material plates based on first-order shear deformation theory. In the real world many components manufactured by FG materials face the buckling load under certain conditions. Various types of gradation law for tailoring the material properties are applied by the researcher, out of that, presently a simple power law for material gradation is applied with shear correction factor (SCF) is used to take account …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 503–513 Read article
-
Exploring Polymer Biocomposite as a Sustainable Filter for Water Treatment
Abstract: The present study explores the utilization of polylactic acid (PLA), a renewable polymer combined with surface-modified nanocellulose (SMNC), and pectin derived from Borassus flabellifer leaves and fruits respectively. Existing methods of filtration are synthetic and affect the environment and public health at an alarming rate thereby making biopolymer-based membranes a greener and effective approach for water treatment. PLA-SMNC-pectin biofilm was fabricated using 88.5 mg PLA, 3.5% (wt. % of PLA) …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 594–608 Read article
-
Fabrication and Characterization of Almond Skin Powder Reinforced PLA Based Composite Filaments for Fused Filament Fabrication
Abstract: Researchers around the globe are increasingly utilizing recycling methods to address waste generated from polymers, spurred by the dire need to deal with environmental challenges promoting sustainable practices. Polymers are having highly-stable long-chain polymer structure which makes it difficult to degrade easily posing many environmental and health challenges, hence, recycling of the polymers is the sole method to mitigate harmful effects. However, there has been relatively little focus on producing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 530–539 Read article
-
Computational investigation of the influence of process parameters of 3D printed PLA material
Abstract: This study uses numerical simulation to examine the relationship between critical process parameters say, feed rate, layer height, and raster angle, on residual stresses and distortions and on the achievable density of FFF prints to identify the optimal input parameter combinations for ISO 527-2 type 1A. Methods of additive manufacturing that are utilised widely used to manufacture thermoplastic parts is fused filament fabrication. High residual stresses are one of the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 259–269 Read article