microstructure
53 articles · search the full text for this term
-
Effect of Hot Induction Process on Bend Properties
Abstract: This paper discusses about the effect of processing speed and water flow rate on the mechanical properties of the hot induction bending of grade API5LX70 for the bending angle of 30o with the bending radius of 3D. Water flow rate & speed of the bending machine were varied to optimize the process parameters with respect to mechanical properties.
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 97–104 Read article
-
Bulk Polycrystalline Ceramic Nanocomposites for Structural Applications: Present Issues and Perspectives
Abstract: This article brings to light some of the unresolved issues associated with bulk structural polycrystalline ceramic nanocomposites (both nano-particulate and nano-fibre reinforced), that even to-date suppress extensive commercial applications and realization of the full potency of the nano-reinforcements. Such issues are primarily related to the presently used processing routes, which in turn influence the microstructure development; and concomitantly the mechanical and tribological properties. The first section introduces this materials class, …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 3, 2014 · pp. 1–7 Read article
-
Analysis of Friction Stir Welded Aluminum Alloys 2014 and 8011
Abstract: In this work we investigated friction stir welding of Aluminum Alloy 2014, Aluminum Alloy 8011. The major defects occurring while friction stir welding are tunnel effect, poor tensile strength, uneven material flow. The main causes for these defects are improper selection of welding parameters. The major welding parameters considered in Friction stir welding are spindle rotational speed (rpm), tool travel speed (mm/min) and tool angle (degree).In this work steps are …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 1, 2015 · pp. 12–17 Read article
-
Effect of Pin Profile on Microstructure and Mechanical Properties of Friction Stir Welded AZ31B Magnesium Alloy
Abstract: Friction Stir Welding (FSW) is a solid state welding technique which was developed primarily for joining soft metal alloys. The aim of the present work was to develop a defect free friction stir joint of magnesium AZ31B sheets and to investigate the microstructural and mechanical properties of the weld. Two types of tool pins namely cylindrical and truncated conical pin profiled tools have been used to analyze its effect on …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 3, 2016 · pp. 1–11 Read article
-
Simulation of Dual Microstructure Heat Treatment Process and Residual Stresses in Gas Turbine Disc by DeformHT Software
Abstract: Gas turbine disc is one of the most vital components in advanced gas engine. In order to improve the tensile strength and fatigue strength of the disc, finer grain size is to be attained at bore area and coarser grain structure at rim area in order to resist the growth of creep. Attempts have been made by several researchers experimentally on the development of dual microstructure for Inconel-718 by heat …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 1, 2017 · pp. 30–42 Read article
-
A Review on an Investigation on the Effect of Immersed Medium in Friction Stir Welding of Aluminium Alloys (AA 6061-T6)
Abstract: Friction stir welding is solid state welding technology used for welding of low melting point metals such as Al, Mg and its alloys. FSW process can be controlled by different parameters like rotational speed, feed rate and welding medium. In this process, a cylindrical non-consumable tool, with a profiled probe (pin) rotating about its own axis is slowly plunged into the abutting edges of work pieces rigidly clamped to a …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 1, 2017 · pp. 9–16 Read article
-
Investigation of Microhardness and Microstructure Using Friction Stir Welding of Dissimilar Aluminium Alloys
Abstract: In this paper Friction Stir Welding (FSW) of two dissimilar aluminium alloys (AA5083 and AA6061) was successfully carried out by considering their advancing and retreating side during the process. It was observed from this experiment that the materials located on advancing side experience a longer contact under the shoulder of tool during process. This contact causes deformed and undeformed material to get larger contact with each other, so that the …
Published in Journal of Communication Engineering & Systems · Vol. 8, Issue 3, 2018 · pp. 37–44 Read article
-
Characterisation of FSW Joints of Aluminium and Titanium Alloys: A Review
Abstract: AbstractThis paper presents a review on friction stir welding of different aluminum and titanium alloys. Aluminum alloys are most widely used in automotive, aerospace and ship building industries as high strength-to-weight ratio materials. Titanium alloys are also attractive in these fields due to their high specific strength and good corrosion resistance. In some special applications, the complementary characteristics of Ti and Al are required, such as increased strength, low weight …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 3, 2018 · pp. 25–29 Read article
-
Characterisation of Plasma Sprayed CNT-Alumina Composite Coatings on Boiler Tube Steel
Abstract: In this research work, the 1.5, 2 and 4 wt.% CNTs-Al2O3 coatings were prepared and successfully deposited on T22 boiler tube steel using plasma spray process. Ni-Cr was also used as bond coat before applying CNTs-Al2O3 coatings. The coatings were subjected to metallography, XRD and SEM/EDAX analysis. The porosity of CNTs-Al2O3 mixed coatings on T22 boiler steel was found to be decreasing with increase in CNTs content. The CNTs were …
Published in Journal of Polymer & Composites · Vol. 5, Issue 3, 2017 · pp. 1–15 Read article
-
Effect of Post Weld Heat Treatment on Mechanical Properties and Microstructure of P11 Weld: A Review
Abstract: Post weld heat treatment (PWHT) is a process of reducing residual stresses and enhancing material properties of any material after welding. The process depends on many parameters like type of material, thickness of material, PWHT temperature, soaking time, heating and cooling rate, etc. Post weld heat treatment is a process of material that could result detrimental effects on tensile strength, yield strength, impact toughness, hardness, elongation, etc. If the process …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 43–47 Read article
-
Resistance Spot Welding of Aluminum Alloy with Reference of Mechanical Properties and Microstructure: A Review
Abstract: This paper presents review on the resistance welding of Al to Al, Al to Mg, Al to Al with steel as an interlayer with focus of mechanical properties and microstructure. Major barrier for the aluminum welding is the surface oxide layer which induces higher resistance for the welding of resistance spot welding. It results in the immediate tip wear of electrode and also gives effect on the properties of weld …
Published in Trends in Mechanical Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 1–6 Read article
-
Characterization of Materials used In Laser Engineered Net Shaping Through Microstructure Analysis: A Review
Abstract: Laser Engineered Net Shaping is a well developing layered manufacturing method in which the metal powders are used to deposit on a substrate with the help of laser. Due to continuous and repeated melting and solidification, the properties of the metals may change by the end of preparation of the components. Microstructure analysis is one of the characterization techniques to evaluate the behavior of the metals after deposition. Many useful …
Published in Trends in Machine design · Vol. 1, Issue 1, 2014 · pp. 57–60 Read article
-
Comparative Study of Commercial Crystalline Waterproofing Admixtures on the Hydration Properties of Cement Pastes
Abstract: Three different types (K, P, and X) of crystalline water proofing admixture have been chosen to study the effect on Portland cement (OPC) pastes. Several studies such as water consistency, setting time, water percolation, heat evolution, differential thermal analysis (DTA), compressive strength and expansion in corrosive atmosphere for the OPC with admixtures in it were performed. Morphology studies of OPC with the admixtures were also carried out. Results indicated better …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 2, Issue 2, 2011 · pp. 1–7 Read article