deflection
9 articles · search the full text for this term
-
Codal Validation and Optimization of Gantry Girders Under Variable Wheelbase and Impact Loads: A Review of Analytical, Numerical, and Codal Approaches
Abstract: Gantry girders serve as critical structural elements in industrial facilities such as steel plants, workshops, and heavy manufacturing units, where electric overhead traveling (EOT) cranes operate. The design of these girders is governed by stringent codal provisions to ensure safety under bending, shear, and deflection. However, discrepancies between codal predictions, analytical formulations, and finite element analysis (FEA) results, particularly under variable wheelbase and dynamic impact loads, have been widely reported. …
Published in Journal of Offshore Structure and Technology · Vol. 12, Issue 3, 2025 · pp. 23–29 Read article
-
Safety of Structure
Abstract: The thickness of structural components is a vital factor in ensuring their durability and stability under various load conditions. In this study, the material thickness is first determined through the application of bending equations, which are used to analyze regions where bending forces are most significant. The bending stress generated by external loads is considered to calculate the required thickness to prevent failure under such stresses. Additionally, the effect of …
Published in Journal of Industrial Safety Engineering · Vol. 12, Issue 1, 2025 · pp. 1–11 Read article
-
Modeling and Analysis of a Diaphragm Micropump with Annular Actuation Using Bond Graphs
Abstract: Micropumps have been around for a while and are utilized for many things, including electrical cooling and biomedical applications. Numerous researchers have experimented with varying the chamber, diaphragm, pumping mechanism, or actuation mechanism materials to improve the device's performance. Despite this, the micropumps employed in the practical applications mentioned above fall short of meeting the necessary flow rates and pressure. In this study, annular actuation is proposed to enhance performance. …
Published in International Journal of Machine Systems and Manufacturing Technology · Vol. 2, Issue 2, 2024 · pp. 34–48 Read article
-
Behavior of SFRC composite pile resting on sloping ground of cohesive and non-cohesive strata
Abstract: Reinforced concrete piles are increasingly being utilized in situations where there is a need to transfer loads in deep strata, particularly for infrastructure projects built on sloping grounds. The present study comprises a finite element analysis (FEA) to investigate the lateral load-bearing capacity of steel fiber reinforced concrete (SFRC) pile, embedded in sloping grounds with sandy and clayey soils. The lateral load capacity of the steel fiber reinforced concrete pile …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 19–31 Read article
-
Performance Analysis of a Three-DOF Piezoelectric Vibration Energy Harvester
Abstract: Mechanical vibration energy can be transformed into electrical energy by a vibration energy harvester, which can then be stored in the battery for later use. It can convert vibrational motions like walking, leaping, running, etc. into pure renewable energy. This can turn previously squandered energy into energy that can be used to recharge wireless sensors and portable electronics. If these gadgets are used widely, they can produce a lot of …
Published in Journal of Polymer & Composites · Vol. 11, Issue 9, 2023 · pp. 10–18 Read article
-
Deflection Analysis of the Leaf Spring Suspension System with the Combination of Helical Springs
Abstract: An efficient and optimized leaf spring suspension system for heavy vehicles must have low deflection but good damping capacity of absorbing shocks and jerks. In this research article, deflection analysis of a modified leaf spring suspension system with the combination of helical spring model is presented. To furnish this end, in the typical leaf spring suspension system model, a helical spring at each side of the master leaf is incorporated. …
Published in Journal of Automobile Engineering and Applications · Vol. 3, Issue 3, 2016 · pp. 21–30 Read article
-
Analysis of Thermally Actuated Micromirrors
Abstract: Use of microelectromechanical system (MEMS) to craft deformable mirror is in the embryonic stage. However, MEMS micromirrors hold significant advantages in speed, compactness, and economy in comparison to macroscale counterparts. The MEMS micromirrors are fabricated by silicon batch processing or micrometer scale lithographic pattering technique which offer flexibility in low volume manufacturing and inter batch variations. The project is a structural study and involves the modeling of various geometries for …
Published in Journal of Mechatronics and Automation · Vol. 6, Issue 3, 2019 · pp. 17–23 Read article
-
Finite Element Analysis of Thin Shell Loaded at the Center
Abstract: Thin rectangular shell structure with clamped edges subjected to concentrated load at the center is modeled as symmetric structure using ANSYS. The shell structure is examined with different length and width combinations. The SHELL181 element is used to model this structure. In general, the results show good agreement with mechanics of materials’ solutions or design tables’ results. A convergence study of the shell structure shows that 10000 elements are sufficient …
Published in Trends in Mechanical Engineering & Technology · Vol. 9, Issue 2, 2019 · pp. 12–20 Read article
-
Study of the Influence of Thermal Tempering on the Bending Behavior of the Silico Soda Lime Glass Material
Abstract: In this contribution, we examine the mechanical behavior of tempered soda-lime-silica glass plates and show that improvements in performance can be achieved through the change of the structural and mechanical properties. Tests of thermal tempering by air jet have been performed on glass plates of different dimensions. Three-point bending tests have been conducted on nontempered and fully tempered float glass plates of four different sizes. A parametric study on the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 160–168 Read article