Coefficient of friction
6 articles · search the full text for this term
-
Experimental Assessment and Statistical Argument of Al-Si/CSA/MoS2 Hybrid Composites for Mechanical and Tribological Characteristics
Abstract: To augment the mechanical and tribological properties of Al-Si matrix composites complement with molybdenum disulphide (MoS₂) and coconut shell ash (CSA), a mixed experimental and Face-Centered Composite (FCC)strategy was employed. A liquid metallurgical method called stir casting was used to create hybrid composites with 5–15 wt.% CSA and 1–3 wt.% MoS₂. A FCC experimental design with thirty runs was used to thoroughly evaluate the materials. This design allowed for the …
Published in Journal of Polymer & Composites · Vol. 14, Special Issue 2, 2026 · pp. 792–802 Read article
-
A Review on Predicting Wear and Friction of PTFE Composites - Fillers to Machine Learning Models
Abstract: Polytetrafluoroethylene (PTFE) composites, a self-lubricating material with low friction, became an indispensable material in engineering applications where load carrying capacity and wear are crucial. The pure PTFE has poor mechanical strength and wear resistance which can be enhanced by the addition of fillers in appropriate volume fraction. The wear performance is dependent on various factors such as fillers, operating parameters, environmental conditions as well as manufacturing attributes. This makes the …
Published in Journal of Polymer & Composites · Vol. 13, Special Issue 4, 2025 · pp. 114–128 Read article
-
Wear Performance of Cylindrical Shaped Alumina Nanoparticles Filled Epoxy Composite
Abstract: Low cost high specific strength epoxy LY 556 and alumina nano filler is utilized in current research for developing a epoxy composite. A liquid dispersion method was adopted for fabricating epoxy alumina composite having 0.50 wt% of alumina reinforcement. For uniform and homogenous dispersion of reinforcement, ultra-sonification of 120 W is adopted. To study the effect of particle behavior, unfilled epoxy and 0.5 wt.% cylindrical alumina oxide filled epoxy composite …
Published in Journal of Polymer & Composites · Vol. 12, Special Issue 5, 2024 · pp. 94–100 Read article
-
Optimization of Wear and Friction Parameters of Al-WC Composite Using Response Surface Methodology
Abstract: This paper aims to optimize the wear and friction parameters of Al-WC composite using response surface methodology. Initially dry sliding wear test on specimen of Al-0WC, Al-5WC, Al-8WC and Al-11WC composites were performed using pin-on-disc equipment under atmospheric conditions, with the varying parameters of the applied load 80KN and Sliding distance 6700m and the sliding velocity is kept constant of 3.34 m/s. The optimum parameters of wear mass loss and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 9, Issue 3, 2019 · pp. 17–26 Read article
-
Experimental Investigation of PTFE Composite Material with Different Filler Materials
Abstract: Experimental investigation of PTFE (Polytetrafluroethylene) composites with different filler materials such as glass fiber, molybdenum disulphide, graphite carried is out in this study. This study exhibits tribological properties such as wear and coefficient of friction of PTEF composite material. Pin on disc tribometer is used to conduct the wear on PTFF polymer composite. Test is conducted on 10 mm diameter PTFE pin against EN31 counter face. Wear and friction experiment …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 34–42 Read article
-
Computational and Experimental Analysis of Nitride Coated Cutting Tools
Abstract: 800x600 Utilization of harder and tougher cutting tool materials is essential in cutting tool industry.Nitride coated cutting tools are becoming alternative materials for machining various materials due to its high mechanical and tribological properties. Demand for coated cutting tools is increasing because of reduced cutting force, increased hardness and wear resistance.In this research article, the TiAlN and CrN coated cutting tool materials for metal removal are studied and compared with …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 3, 2015 · pp. 65–72 Read article