Search
68 articles for “Amplitude”
-
Application of Radial Basis Function Neural Network in Power Quality Events Classification
Abstract: Power Quality concerns have become more important as the Smart Grid has evolved. Computers, microprocessor-controlled electronic loads, and power electronic devices are all used in urban development. Disturbances in power quality are caused by these electronic devices. Variations in the amplitude and frequency of system voltages and currents from their nominal levels identify PQ difficulties. We offer a hybrid technique to accomplishing this goal in this paper. To classify PQ …
Published in Trends in Electrical Engineering · Vol. 12, Issue 1, 2022 · pp. 20–40 Read article
-
Experimental Investigations on Concentric Flow Dry Ultrasonic Assisted Wire Electric Discharge Machining (CFDUAWEDM) Using Regression Analysis
Abstract: This paper presents an application of concentric flow mode of dry dielectric (compressed air) supply for ultrasonic assisted wire electric discharge machining process (CFDUAWEDM). The concentric flow mode of dielectric supply using ultrasonic assistance is expected to offers improved surface integrity, environmental and operator friendliness during wire electric discharge machining (WEDM) process. Experimental set up was developed wherein, the ultrasonic vibration was applied to the electrode wire using an ultrasonic …
Published in Trends in Machine design · Vol. 3, Issue 2, 2016 · pp. 33–43 Read article
-
Vibration Analysis Of Pump Shaft Using Finite Element Analysis Software: A Review
Abstract: Rotating shaft and other components in pump system revolving at speed close to the natural frequency of the system are unsafe because at natural frequency the amplitude of vibration is highest and it generate the excessive stresses which can cause rotating components failure. The objective of the review paper is to study the vibration characteristics of pump shaft system of finite element method in software module. The knowledge about the …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 1, 2018 · pp. 46–54 Read article
-
Multi Objective Optimization in Micromilling of 304L steel by Taguchi-Grey-Fuzzy Method: Literature Review
Abstract: Micromechanical milling of 304L Stainless steel which is commonly used in the welded in severe corrosion environment and it terminates the need for annealing. The goal of this study is to investigate the influence of process input parameter such as cutting speed, depth of cut, feed per tooth, radial immersion percentage and plunging method on process output during circular pocketing operations. Tool wear, machining forces and surface roughness measurement are …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 2, 2020 · pp. 25–30 Read article
-
Effect of Outdated CSI in a Multiuser TAS/MRC System over Correlated Nakagami-m fading
Abstract: The TAS/MRC system is a widely accepted technique to reduce the complexity level of a multiuser MIMO system with little reduction in the performance. This increases the practical applicability of TAS/MRC system. In TAS/MRC algorithm the channel state information (CSI) is provided to the transmitter for selection of best transmitting antenna for better system performance. However, two important factors may reduce the performance of the TAS/MRC system considerably, out dated …
Published in Journal of Communication Engineering & Systems · Vol. 8, Issue 2, 2018 · pp. 38–46 Read article
-
Comparison of Ultra Wide Band Indoor Multipath IEEE 802.15.3 Channel Model
Abstract: ABSTRACT A very large bandwidth of frequency (3.1–10.6 GHz) has been allocated to UWB systems. A single-band UWB signal propagates differently in the lower and upper bands of the spectrum due to the size of its bandwidth. The lower part of the signal can be obstructed more easily and the man-made interferences are not homogeneously distributed over the whole spectrum. The first experimental results obtained for a UWB channel show …
Published in Journal of Communication Engineering & Systems · Vol. 2, Issue 3, 2012 · pp. 20–25 Read article
-
Binary GA for Sidelobe Reduction and Null Steering in 5G Array
Abstract: This paper presents a comprehensive performance evaluation of a Binary Genetic Algorithm (BGA) for optimizing radiation characteristics of an active phased array antenna used in fifth-generation (5G) wireless communication systems. The primary objective is to achieve effective null steering while maintaining the desired main beam direction and simultaneously reducing the side lobe level (SLL). These improvements are essential for minimizing co-channel interference, enhancing spatial selectivity, and improving the Signal-to-Interference-plus-Noise Ratio …
Published in International Journal of Radio Frequency Innovations · Vol. 4, Issue 2, 2026 Read article
-
Monitoring the Structural Health of RC Beam Lap Splices using Wave Propagation and PZT Sensors
Abstract: This paper describes the use of piezoelectric sensors in a wave propagation-based Structural Health Monitoring (SHM) method to identify lap splices in steel reinforcing bars. Straight and lapped steel bars with lap lengths of 10° and 20° were used for the experiments. Lead Zirconate Titanate (PZT) transducers were employed, one of which served as an actuator to produce stress waves and the other as a sensor to record the signals …
Published in Journal of Experimental & Applied Mechanics · Vol. 17, Issue 2, 2026 · pp. 65–70 Read article