Journal of VLSI Design Tools and Technology
Volume 8, Issue 1 (2018)
Published
Table of contents
-
Fault Detection Attainment for Embedded Cores based on Software Test Routines
Abstract: The test circuitry is designed in built-in-self-test (BIST) technique involves a system that applies the test signals and observes the corresponding system response. In this technique, the framework is embedded directly into the system hardware. The testing process performs efficiently, fastly and more economically than using an external test setup. Self-testing of embedded processors based on the test routines is an emerging method, since it employs a test resource partitioning …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 1–6 Read article
-
Memristor based Material Implication Logic for Implementation of Basic logic Gates and Circuits
Abstract: A physical memristor was realized a few years back by Hewlett Packard labs. Instantly it became the topic of interest for many scientists and researchers. Memristor has joined resistor, capacitor and inductor in the list of basic two-terminal passive circuit elements. Field Programmable Gate Arrays (FPGAs) have become a major choice of technology for the implementation of various digital circuits because they offer various features such as quick time to …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 17–22 Read article
-
AXI Bridge and DMA/Bridge Subsystem for PCIe
Abstract: We know that the present-day SOC design consists of many intellectual property cores with several communication protocols. To enhance the performance of the whole system, we need to improve the bridging and signal translation between these protocols. In this article, discussion has been carried out on PCIe and AXI protocol from AMBA. PCI Express, because of its various features like high speed, low power consumption, and good protocol efficiency can …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 23–29 Read article
-
Comparative Analysis of Combinational Circuit Using Reversible Logic Based Techniques
Abstract: In the last few decades, due to the ever growing demand for portable and small sized devices, integrated circuits require electronic circuit design methods to implement integrated circuits with low power consumption. The ever-growing number of transistors integrated on a chip and the increasing transistor switching speed in recent decades has enabled great performance improvement in computer systems by several orders of magnitude. Adiabatic logic technique is one of the …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 30–33 Read article
-
High Speed and Low Power Basic Digital Logic Gates, Half-Adder and Full-Adder Using Modified Gate Diffusion Input Technology
Abstract: In this paper, modified gate diffusion input (MGDI) technology has been used for the design and implementation of digital integrated circuits (ICs). In today’s digital world, IC plays a vital role in high-performance computing, communication, and many consumer electronics. IC manufacturing technology has scaled down to smaller device dimensions. This scaling has a great impact on the design of digital ICs. The main objective of the IC manufacturing technology is …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 34–42 Read article
-
Review Paper: Low Power SRAM Cell using FinFET Technology
Abstract: To make portable battery operated devices more efficient with low leakage current has become a major challenge with the technology scaling. As the technology is scaling, the bulk MOSFET faces various challenges which lead to increased leakage current. FinFET is the most encouraging substitute to bulk CMOS, because of the reduced short channel effect. The FinFET device based circuits portrays advantages with its better control over the device channel and …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 43–47 Read article
-
Review Paper To Design a Low Power CNTFET Based XOR Gate
Abstract: The continuous scaling down of Silicon technology leads to various critical challenges and reliability issues such as short channel effect, high leakage current, interconnect problems, etc. CNTFET is the most probable substitutes to traditional MOSFET. The CNTFET device based circuits portray advantages with its better control over the device channel, reduced leakage current, reduced short channel effects. The CNTFET based XOR gate circuits incur the minimum power and energy dissipation. …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 48–53 Read article
-
High Speed Low Offset Power Efficient Fully Differential Double Tail Dynamic Comparator
Abstract: This paper comprises a novel fully differential double tail high performance comparators suitable for low-voltage low-power applications. A fully differential double tail comparator has been designed to meet the requirement of high speed, low power consumption with low offset voltage. Authors have proposed novel architecture of dynamic voltage comparator which is differential and double tail and verified the architecture by simulation in TSMC 180nm technology with ±0.9V supply. The proposed …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 7–16 Read article