Journal of Polymer & Composites
Volume 9, Issue 3 (2021)
Published
Table of contents
-
Assessment on the Physical Characteristics of Polymer Materials for Additive Layer Manufacturing Processes
Abstract: Polymer materials have the capacity to morph into a soft form and flow when heated, then return to their original hardness when cooled, making them excellent for heat fabrication procedures. Acrylonitrile Butadiene Styrene (ABS) is a high-grade polymer with exceptional mechanical qualities and heat resistance that is commonly used in aircraft and vehicle manufacture. These polymers are mixed with other materials to create alloys, which are primarily used in the …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 1–9 Read article
-
Thermally Trigged Self-Healing Smart Shape Memory Polymer Composite
Abstract: Temperature-responsive self-actuating PU/MWCNTs composites were prepared with micro-compounder through in-situ polymerization. For making of 1CNTPU composite sample 1 part per hundred multiwall Carbone nanotubes (MWCNTs) were reinforced into the neat polyurethane (PU) base matrix. Surface characterizations for pure and composite have studying by using Atomic Force Microscope (AFM), high resolutions Scanning Electron Microscopy (SEM). Properties like shape recovery, storage modulus, loss modulus, tensile stress, degree of hardness, and flexural stress …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 10–18 Read article
-
Cubic B-splines for Isogeometric Analysis of Laminated Composite Plates Subjected to Hygroscopic Loading Using Classical Laminated Plate Theory
Abstract: Composite laminates are inevitably used in several engineering structures due to their high strength and stiffness to weight ratio. The laminates are subjected to change in moisture content and the flexural behavior leads to change in the strength. Presence of moisutre may induce residual stresses and strains. Isogeometric analysis is a well-proven method to perform analysis of laminated composite plates. The main focus of this study is to apply isogeometric …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 19–32 Read article
-
Influences of Silica Fume to Engineering Properties of High Volume Fly Ash Concrete (HVFC)
Abstract: High volume fly ash concrete (HVFC) is one kind of the most promising concrete materials in the 21st century. HVFC has special properties such as high flowability, mechanical strength meets the requirements of contruction standards, low permeability, high durability, and others. Furthermore, HVFC is able to continuously develop strength during long time because the high activity alumina-silicates in the fly ash particles are dissolved slowly and prolong. Therefore, this study …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 33–44 Read article
-
Predicting Rate Equation for the Synthesis of Octadec-9-Enoic Acid Methyl Esters by the Methanolysis of Pongamia Pinnata Triglycerides Using Sono Reactor
Abstract: In the present work, octadec-9-enoic acid methyl esters are synthesized from pongamia pinnata oil using methanolysis in sono reactor. The rate equation is predicted for the methanolysis reaction. The produced methyl esters from pongamia pinnata oil confirmed to ASTM D6751 standards. Fourier Transform Infrared Analysis and Gas Chromatography Mass Spectrometry were used to characterise the methyl esters. The rate is dependent greatly on methanol concentration, and then on catalyst concentration …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 45–55 Read article
-
Studies on Mechanical, Optical, Barrier Properties and Characterization of LDPE-PLA Blend Films with Micro Clay
Abstract: Low density poly ethylene (LDPE) and Poly lactic acid (PLA) in the ratio of 70:30 wt% were blended along with ethylene glycidyl meth acrylate (EGMA) as compatibilizer (2.5%), benzophenone as photodegradable additive (1%) and microclay (1,3,5%) as filler. Blending took place in a twin-screw extruder and then the resulting blend was processed into a film using blown film extrusion. Mechanical, optical, barrier and degradative properties of film were tested as …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 56–66 Read article
-
An Approach on Optimization of Thermo Physical Properties of Teak Wood Dust Filled Polymeric Composites
Abstract: The aim of the present work was to prepare the specimens with the help of hand-lay-up technique to measure the thermal properties of TWDPC. The density & voids of TWDPC were measured to determine its physical property & significantly affected some of its mechanical properties. Taguchi experimental method was applied to optimize its thermal properties. The optimal factor combinations were determined with the help of ANOM & the analysis of …
Published in Journal of Polymer & Composites · Vol. 9, Issue 3, 2021 · pp. 67–80 Read article