Wear
26 articles · search the full text for this term
-
A Review of the Bionic Surfaces for Engineering Applications
Abstract: The word ‘bionics’ refers to copying Nature, or taking ideas from Nature. As the field is increasingly influencing the emerging subjects of science and engineering, it has innumerable applications in fields such as robotics, product design, automobile components and biomaterials. This paper emphasizes the development of bionic surfaces for various engineering applications. It gives the relevance of bionic surfaces mimicked from insects/animals. It also presents a critical review of the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 1, Issue 1-3, 2011 · pp. 1–17 Read article
-
Evaluation of Mechanical Property and Optimization of the Dry Sliding Wear Behavior of Carbon Black-Alumina-Epoxy-Glass Composite by using Design of Experiments
Abstract: The research work is mainly focused on investigating the effects of wear parameters: filler content (0%, 4% CB, 4% Al2O3,and 2% CB + 2% Al2O3), applied load (4.905, 9.810, 14.710, and 19.62 N), sliding distance (20, 30, 40, and 50 mm) by using Design of Experiments (DOEs) approach. The experimental results were analyzed using MINITAB V16 scientific graphical and data analysis software. Signal-to-Noise (S/N) ratio, analysis of variance (ANOVA) proved …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 2, 2014 · pp. 21–31 Read article
-
Dry Sliding Wear Behavior of Al2O3-TiO2 Coated Ti6Al4V Alloy based on Taguchi Method
Abstract: AbstractTi6Al4V alloys are extensively used as implant material for bio-medical applications due to their high specific strength. But, their poor wear resistance results in formation of wear debris in implants and causing soreness. In this work, Al2O3-TiO2 coatings were applied to improve the wear resistance and hardness. Al2O3-TiO2 coatings are deposited on the substrate with 100, 200, 300, 400 µm thickness using detonation spray (DS). Pin on disc wear tests …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 2, 2017 · pp. 28–34 Read article
-
Tribological Behaviour of Epoxy-Marble Powder Composite with Taguchi Optimization Technique
Abstract: Epoxy resin strengthened with marble powder particles is prepared by ultrasonic mixing strategy. Pin-on-Disc wear trial of the developed composite is done concurring with Taguchi optimisation. An orthogonal array is displayed and analysed the affecting parameters like fraction of marble powder reinforcement, load, sliding speed and track diameter on the composite. Signal to noise ratio analysis optimises the parametric conditions that yield minimum wear rate, minimum frictional force and minimum …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 2, 2018 · pp. 110–117 Read article
-
Experimental Investigation of PTFE Composite Material with Different Filler Materials
Abstract: Experimental investigation of PTFE (Polytetrafluroethylene) composites with different filler materials such as glass fiber, molybdenum disulphide, graphite carried is out in this study. This study exhibits tribological properties such as wear and coefficient of friction of PTEF composite material. Pin on disc tribometer is used to conduct the wear on PTFF polymer composite. Test is conducted on 10 mm diameter PTFE pin against EN31 counter face. Wear and friction experiment …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 34–42 Read article
-
Use of Fuzzy Logic Method for the Optimisation of the Wear Parameters of Aluminum Alloy
Abstract: In this paper, use of fuzzy logic in the Taghuchi method for the optimisation of the wear parameters of aluminum alloy is explained. An experiment was conducted on three alloys viz. Al-25Zn-2.5Cu-5SiC, Al-25Zn-2.5Cu-10SiC, Al-25Zn-2.5Cu-15SiC. Experiments were carried out on standard pin-on-disc machine, at ambient temperature and under dry operating condition. The three process parameters like sliding velocity, load and sliding distance were optimized. In the Taguchi method, L27 orthogonal array …
Published in Trends in Mechanical Engineering & Technology · Vol. 5, Issue 1, 2015 · pp. 20–25 Read article