heat transfer coefficient
8 articles · search the full text for this term
-
Passive Augmentation Studies in a Double Pipe Heat Exchanger with Ellipsoidal Dimples
Abstract: In this work, the numerical studies of heat transfer augmentation of a counter-current double pipe heat exchanger with ellipsoidal dimples (inward-facing, raised dimples) on the inner tube was performed using SOLIDWORKS software. The effect of dimple depth, dimple pitch and number of dimples/angles between two dimples on heat transfer was investigated at a constant volumetric flow rate of 4 LPM for hot (water) and cold (water) fluids. The effect of …
Published in Journal of Thermal Engineering and Applications · Vol. 13, Issue 2, 2026 Read article
-
Thermal Performance Analysis and Optimization of Pin-Fin Heat Sink Using CFD, Taguchi Method, and Machine Learning
Abstract: Efficient thermal management is essential for improving the performance and reliability of modern engineering systems and electronic devices. This study presents the design, simulation, and optimization of a pin-fin heat sink using SolidWorks for three-dimensional modeling and ANSYS for thermal and computational fluid dynamics (CFD) analysis. Four different pin-fin geometries, namely square, pentagon, octagon, and circular fins, are considered to evaluate their thermal performance under varying operating conditions. Aluminum is …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 2, 2026 · pp. 8–20 Read article
-
Thermal Analysis of Casting using ANSYS: A Review
Abstract: The major requirement of any foundry is to provide the high quality casting products. Since the quality is depended upon thermal stress and solidification of the casting, a thermal analysis is a key area to work on. Heat transfer coefficient is the vital element of any thermal analysis. Mould and the casting interface is the most critical area that gets affected during the solidification. Heat transfer ratio at the inter …
Published in Journal of Production Research & Management · Vol. 6, Issue 1, 2016 · pp. 19–27 Read article
-
Effect MFD Viscosity on Bénard–Marangoni Ferroconvection in a Rotating Ferrofluid Layer with Convective Surface Boundary Condition
Abstract: AbstractThe combined effect of Coriolis force due to rotation and magnetic field dependent (MFD) viscosity on the onset of Bénard–Marangoni convection in a horizontal layer of ferrofluid is investigated theoretically. The lower boundary is taken to be rigid–isothermal, while the upper free boundary open to the atmosphere is flat and subject to a convective surface boundary condition. The Galerkin technique is employed to extract the critical stability parameters numerically. It …
Published in Recent Trends in Fluid Mechanics · Vol. 7, Issue 2, 2020 · pp. 12–32 Read article
-
A Review on Roughened Solar Air Heater for Heat Transfer and Thermal Efficiency
Abstract: The use of artificial roughness on the absorber plate is the most effective technique to enhance the thermal performance of solar air heaters. Experimental investigation of distinct roughness geometries shows that the enhancement in the rate of heat transfer is accompanied by considerable rise in temperature. In this paper some distinguished roughness geometries have been compared on the basis of heat transfer rate and thermal performance. The objective of this …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 1, 2015 · pp. 49–56 Read article
-
CFD Analysis of Effect of Forced Vibration on Heat Transfer in Laminar Flow
Abstract: Vibration of pipes conveying fluid is an important problem present in installations which are normally used in petroleum industries, hydropower systems, food processing industries, chemical plants and hydraulic power systems. Research is needed to further understand and be able to predict the flow behavior and investigate ways of improving their processing. The current work involves the numerical simulation of flow and heat transfer under an externally imposed mechanical vibration. CFD …
Published in Journal of Thermal Engineering and Applications · Vol. 2, Issue 1, 2015 · pp. 1–9 Read article
-
Heat Transfer in Pool Boiling of H2O/LiBr Mixture
Abstract: This paper presents the results of an experimental investigation carried out to study the heat transfer in saturated nucleate pool boiling of the H2O/LiBr bromide mixture on a heated vertical copper cylindrical rod at atmospheric pressure. The mass fraction of lithium bromide was varied from 0 to 0.5. It was observed that the heat transfer coefficient increased for the mixture with an increase in heat flux and lithium bromide concentration. …
Published in Journal of Thermal Engineering and Applications · Vol. 1, Issue 1, 2014 · pp. 7–12 Read article
-
Determination of Heat Transfer Coefficient in Solar Collector Tube under Simulated Operating Conditions
Abstract: Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 In this paper, heat transfer coefficient, in solar collector tube under scaling conditions has been experimentally determined using a specifically fabricated test apparatus. The effect of various variables such as scale thickness, flow conditions and tube wall temperatures on heat transfer coefficients have been investigated. The experimental results reveals that the scale thickens has a dominating effect on heat transfer coefficient.Keywords: …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 4, Issue 1, 2013 · pp. 7–12 Read article